Search results for: 'foot ripper r pdc 2020 for skid'

Make: Forward Model: RC3 Year: 2024 Hours: 128 Engine: Cummins 6BTA Drilling Capacity: 380 m Drilling Diameter: 10" Inches Drill Head Rotation: 0-120 RPM / 5,600 Nm Pull Back Force: 120 kN Hoist Capacity: 20 kN Feed Stroke: 3,400 mm Mast Height: 6,400 mm Mud Pump: 450 Litres per minute at 1,000 PSI Crawl Speed: 3 km/h Weight: 1,180 kg Dimensions: 6,400 x 2,250 x 400 - Remote Tramming - Jack Legs - Mast Tilt - Mast Pump Includes; - 150 Metres of Rods & Different Sized Bits - Settling Tank - Hoses Modifications; - P.R.D Dual Breakout 210 mm Diameter (Can be swung out of way to allow larger install) - Larger Hydraulic Pump Installed Track Mounted Water Well Drill Rig Location: Western Australia Learn More

Make: Kurth Model: KB25 Rotation Speed: 0-120 RPM Max. Torque: 5,000 Nm Stroke: 2,300 mm Max. Pullback Force: 48 kN Max. Feed Force: 32 kN Max. Casing Clamping Diameter: 273 mm Max. Casing Pullback Force: 150 kN Rotary Drive Travel Speed: 40m/min (max.) Rotary Drive Tilt Out Angle: 40 degrees from vertical - Set up for Shell & Auger - Drilling & Casing Clamp Range from 114 mm OD to 219 mm OD Drilling Capacity; Auger Drilling with Casings Ø 219/178 mm: 25-40 metres Hollow Stem Augers Ø 195/110 mm: 40 metres Direct Mud Rotary Drilling Ø 190 mm: 100 metres Down Hole Hammer Drilling Ø 150 mm: 100 metres Track Mounted Rotary Drill Rig Location: Western Australia Learn More

Model: VB10 Engine: Deutz TCD2012L04 4 Cylinder Working Pressure: Max. 350 Bar Torque (Inside Rods): 3,700 / 7,400 Speed: 120 / 60 RPM Torque (Outside Rods): 12,000 / 24,000 Speed: 54 / 27 RPM Max. Breaking Torque: 46,000 Nm Drill Pole; Pole Profile: 300 x 200 x 8 mm Pole Height: 7,190 mm Stroke: 3,600 mm Hook Load / Pulling Force (Chain): 120 kN / 245 kN Max. Contact Pressure (Chain): 60 kN Travelling Speed: Up to 40 m/min Max. Rod Length: 2 m Track Mounted Dual Rotary Drill Rig Location: Western Australia Learn More

Make: Gardner Denver Type: 5x6 Engine: Kubota V3300 4 Cylinder Water Cooled - Diesel Driven - Manual Clutch - Belt Drive - Pulsation Dampener - OTECO Pin Pressure Valve - 200 Litre Fuel Tank Dimensions; Length: 2,950 Width: 1,500 Height: 2,300 Weight: 2.4 Tonne Skid Mounted Duplex Mud Pump Location: Queensland, Australia Learn More

Make: Gardner Denver Type: 5x6 Engine: Kubota V3300 4 Cylinder Water Cooled - Diesel Driven - Manual Clutch - Belt Drive - Pulsation Dampener - OTECO Pin Pressure Valve - 200 Litre Fuel Tank Dimensions; Length: 2,950 Width: 1,500 Height: 2,300 Weight: 2.4 Tonne Skid Mounted Duplex Mud Pump Location: Queensland, Australia Learn More

Make: Foremost Model: 306430 Pin: 6" Inch API Box Thread: 7.5" Inch Rod BECO Part Number: 322424 US Pat Number: 6332841 Serial Number: 1000166 Shock Sub Location: Western Australia Learn More

Make: Foremost Model: 14-50-6353 Pin: 4.5" Inch API Box Thread: 4.5" Inch API Part Number: 320316 Serial Number: 968176-2 - Refurbished Shock Sub Location: Western Australia Learn More

Make: Gardner Denver Model: 200-FXX-001 Type: 5x8 - High Pressure - Fully Refurbished Skid Mounted Mud Pump Location: Queensland, Australia Learn More

Make: Gardner Denver Model: 8FXX172 Year: 1990 Skid Mounted Duplex Mud Pump Location: Queensland, Australia Learn More

Make: Sandvik Model: DE712 Depth Capacity: 1,126 m (3,693 ft) N Size Feed Force: 5.5 Tonne (12,000 lbf) Pull Force: 9.3 Tonne (20,500 lbf) Feed Length (Stroke): 3.45 m Speed (Up & Down): 30m/min Track Mounted Drill Rig Location: Queensland, Australia Learn More

Make: Caterpillar Model: D9 Hours: Approx. 1,300 Engine: Caterpillar C18 @ 477 HP Track Shoes: 610 mm Track Rollers: 8 + 8 (Both Sides) - SS Ripper - SU Single Tilt Blade - Air Conditioned Cabin Track Mounted Crawler Bulldozer Location: India Learn More

Make: Epiroc Model: MCS30 Year: 2020 & 2021 Hours; Unit 1: 60 Unit 2: 148 Quantity: 2 Spraymec Concrete Sprayer Location: China Learn More

Make: Komatsu Model: D475A-5E0 Year: 2023 Hours: 6,075 - Needs Plates and Sprockets - Complete with Blade and SS Ripper Track Mounted Crawler Bulldozer Location: Middle East Learn More

Make: Epiroc Model: Rocket Boomer 282 Year: 2017 Hours: 6,610 Percussion Hours: 3,009 / 2,987 Electric Hours: 3,601 / 4,113 Drill: COP 1838 HD+ - Double Arm - Fixed Beams of 16' Foot Drill Rig Location: Peru Learn More

Make: Terex Model: Hi-Ranger TM105 Year: 2007 Hours: 1,026 / 711 (PTO) Working Height: 105' Foot / 32 Metre Side Reach: 51' Foot / 15.5 Metre - 66kV Insulated Boom - Flashing Beacons - In Date until 12/2030 *Truck Is Not Included* Elevating Work Platform Location: Western Australia Learn More

Includes; - 7x NMLC Bit and Reamers - 3x NMLC Bits - 2x NMLC TC Core Bit - 1x HMLC Used Bit and Reamer - 1x HMLC New S15 Core Bit - 1x HMLC New Reamer - 1x HMLC Used Core Bit - 1x Tri Cone 2 15/16" Inch - 1x Tri Cone 3 7/8" Inch - 1x HQ3 Bit Reamer Fordia S11/14 - 5x HQ3 Used IMP Bits - 2x HQ3 TC Core Bits - 1x PQ3 Near New IMP Core Bit - 1x C4 IMP Bit and Reamer - 1x NW IMP Shoe Bit - 1x NW TC Shoe Bit - 1x HQ Rod TC Shoe Bit - 2x NQ3 Near New IMP Core Bits - 3x NQ Reamers - 1x NQ Rod Reamer - 1x NQ New IMP Core Bit Hayden S14/15 - 1x HQ New Reamer - 1x HQ Near New Reamer - 1x New 3 7/8" Inch Drag Bit - 2x Near New 4 1/2" Inch Drag Bit - 1x NMLC New Hard Core S6 - 1x NMLC New Reamer - 1x NQ3 Hard Core S15 - 9x 2 Metre Used RC Rods - 1x Used 1.5 Metre RC Rod with Bit - 4x Worn Augers - 1x Used 4 1/2" Inch Bit - 1x New 4 1/2" Inch Bit - 1x 6 1/2" Inch Drag Bit - 1x 100 mm Tube Adapter - 1x 75 mm Tube Adapter - 2x 50 mm Tube Adapter Plus 50 mm Piston Sampler Drilling Consumables Package Location: Queensland, Australia Learn More

Make: Wacker Neuson Model: TH412 Year: 2020 Hours: Less than 500 Engine: Yanmar 3TNV80FT @ 25HP Chassis Operating Pressure: 5,510 PSI / 380 bar Hydraulic Operating Pressure: 3,190 PSI / 220 bar Payload Max: 1,250 kg Payload Lift Max: 1,250 kg Lift Bucket Swivel: 4,537 mm Dimensions Length: 3,944 mm (2,991 mm w/out Bucket) Width: 1,564 mm Height: 5,280 mm (1,995 mm Just Cab) Weight: 2,750 kg - Forklift Attachment - Side Shift - Air Conditioning / Heating & Ventilation - ROPS / FOPS tested with VSG safety window on right side - Front, Roof & Rear Wipers - Heated Rear Window - Tilt Display - Sun Shade - Bottle Holder - Storage Net - LED Work Lights (1x Front & 1x On Cab Roof) Telehandler Location: Western Australia Learn More

Make: AFHTechFLOW Package Type: Gas Heating & Pressure Regulating Skid Application: Fuel gas conditioning for gas engine / generator Year: October 2014 Fluid: Natural Gas / Fuel Gas Typical End Use: GE Jenbacher Gas Generator Fuel Gas Train Electrical Supply: 415 V, 3-phase, 50 Hz Heater Power Load: ~11 kW Gas Inlet Connection: Flanged pipeline inlet Gas Outlet Connection: Flanged connection to engine gas train Drains: Heater vessel drain Relief: PSVs vented to atmosphere Earthing: Dedicated skid earth lug Nominal Gas Flow: 330 Nm³/hr Maximum Flow Rate: 330 Nm³/hr Inlet Pressure (Operating): 35 – 90 barg Inlet Pressure (Design / MAOP): 102 barg (upstream of regulator PRV2301) Outlet Pressure (Operating): 4 barg Inlet Temperature: 2 – 60 °C Outlet Temperature: 0 – 40 °C Design Temperature Range: -15 to +60 °C Gas Quality Assumption: Pipeline Quality Natural Gas Gas Heating System; - Electric gas heater, 10.8 kW - Explosion-protected heater suitable for Zone 1 - Carbon steel pressure vessel heater housing - 100 NB, Class 600 - Designed to AS 1210 PT100 RTD temperature elements; - Element sheath over-temperature protection - Heater outlet temperature control Thyristor-controlled heater system; - Control panel supplied separately for non-hazardous area installation - Heater pressure safety relief valve Pressure Control & Safety; - Primary pressure regulator (carbon steel body) - Over-pressure shut-off valve with fracture disk - Pressure safety relief valve (PSV) - Pressure gauges with block and bleed valves - Manual isolation ball valves (Class 800) Gas Filtration & Separation; - Cyclone separator for liquid droplet removal - Particle filter rated >3 µm - Designed to prevent condensate and solids entering engine gas train Fuel Gas Conditioning Skid Location: Queensland, Australia Learn More

Make: Foremost Type: 4 1/2" Inch Connector Tube Pipe (CTP) - Reverse Circulation OD: 4 1/2" Inch x 3 1/4" Inch ID (Approx.): 3 1/4" Inch (without inner tubes) - Currently has "BAD" Steel Inner Tubes Installed (Inner Tubes can be removed by pressing; with PIN down and push out BOX end) Quantity: 140 Drill Pipe / Rod Location: United States of America Learn More

Rig Make: Schramm Model: T660 Rotadrill Year: 1984 Hours: 4,131 Air Compressor: GHH 750 CFM / 250 PSI @ 2,100 RPM Deck Engine: Detroit 8V92 Diesel Winch Pullback: 44,000 lbs - Caterpillar Water Injection System - Set Up as Top Head Air Rotary - 7 Rod Carousel - Hammer Oiler Truck Make: Brigadier Engine: Caterpillar 3208 Miles: 41,546 Transmission: 13 Speed GVW: 53,320 lbs FVW: 15,320 lbs RVW: 38,000 lbs Drill Pipe; - 4 1/2" Inch - 220' Foot Bottle Neck Truck Mounted Drill Rig Location: United States of America Learn More