Search results for: 'brand gear hose for side'

Make: Everdigm Model: Rocky B180 Bit Shank: N180 Shank Connection: API 8-5/8" Inch Reg. Pin Piston Stroke: 5.75" Inch Cylinder Bore: 12.28" Inch Hole Sizes: 18" Inch ~ 26" Inch Wrench Size: A/F 14" Inch - Brand New - Bailing Subs/Break Out Plate, etc. - Hammer forklift cradle included - 19” Hammer bit included (unused) RS Hammer Location: Queensland, Australia Learn More

Rig Make: Hanjin Model: D&B-8D Year: 2016 Hours: 5,800 Pull: 6 Metres - Warman Clamps - Under Casing Clamps - Wireline and Main Winch - Rod Bin - Auger Carrying Rack at Front of Rig - Auto SPT - Silvan Pump - All New Suction and Hydraulic Hoses for Pump with Camlocks - 2x Mud Tanks (1,000 L & 500 L - Plastic) Down Hole Gear - 10x 3m PQ Rods Plus Shorts - 10x 3m HQ Rods Plus Shorts - 10x 3m NQ Rods Plus Shorts - 10x 3m Junior Mayhew Rods with Spanner Flats Plus 2x 1.5 m - 5x 100mm x 1.5m Augers Plus Bit & 20 Pins - 2x 1.5 NMLC Core Barrels - 6x NMLC Core Bits - 4x Impreg & 2x Surface Set - 40x Core Lifters / 6x Cases / 40x Stop Rings - 2x NMLC Reamers - 2x BQ Reamers - 3x BQ Core Bits - 2x 1.5m NQ3 Core Barrels - 2x Sets of Splits - 1x 3m NQ3 Core Barrel - 2x Locking Couplings - 2x Adaptor Couplings - Box of Barrel Spares - 1x HQ/NQ Overshot - 1x Set of PQ, HQ, NQ Inner Tube Wrenches - 10x 75mm Shelby Tubes Plus Drive Head - 10x 50mm Shelby Tubes Plus Drive Head - 2x SPT Samplers - 2x Pulling Plugs - 1x Spare Water Swivel Plus 2x Repair Kits - 1x Repair Kit for Rig Swivel - Many Subs to Facilitate all the Drilling Requirements - Stillsons - 2x 36" Inch, 2x 24" Inch & 2x 18" Inch - 1x Gas Mig Welder - 1x Honda 3.5 kVA Powered Generator - 1x PQ Birds Mouth for Water Return to Mud Tanks - 1x HQ Birds Mouth for Water Return to Mud Tanks - New Suction and Delivery Hoses - 1x 100mm Down Hole Hammer with 2x Bits 118mm *New* - 1x 75mm Down Hole Hammer with 2x Bits 95mm *New* Support Truck Make: Mitsubishi Model: Canter Year: 2009 Type: 4x4 - Hydraulic Hi-Ab Crane - 500 Litre Water Tank - 400 Litre Diesel Tank for Rig & 12 Volt Pump - 1x kVA Inverter - Wired so diesel pump won't engage until the switch is turned on in the locked tool box. - 1x Centrifugal Pump 1 1/2" Inch plus Suction and Delivery Hoses with Camlocks - 2x Tool Boxes - 1x Box of Hand Spanners & Sockets - Fitted Drill Rod Bins & Core Barrel Bins - Currently Registered until May 2025 Tracked Mounted Drill Rig Support Truck + Down Hole Gear Package Location: New South Wales, Australia Learn More

- Complete Foot Clamp (ex Jaws) - BQ Jaw Set c/w Teeth - NQ Jaw Set c/w Teeth - HQ Jaw Set c/w Teeth - PQ Jaw Set c/w Teeth - PWT Jaw Set c/w Teeth - In Cast PQ Jaw Set - Jaw Teeth Insert Set *Brand New Location: New South Wales, Australia Learn More

Make: Gardner Denver Model: SCH2500 Year: 1990 approx. Engine: Cummins 6 BTA 5.9 Serial Number: 2711468 - Includes Drill Rods and Sampling Equipment Complete Overhaul; - Hammer HPRI - New Head Injectors on Fuel Pump - Track and Final Drives - Oil Cooler Replaced with CAT Cooler and mounted on left hand side Hydratrack Track Mounted Blast Hole Drill Rig Location: Queensland, Australia Learn More

Sizes: 3" Inch / 4" Inch / 5" Inch Working Pressure: 2,500 PSI - Basic Hard Shut in Nitrile Bladder - Wireline Stripper - Hydraulic Activator - Hand Pump Activator - All Hoses Burst Protection or Fire Protected - Zone One Hoses are Coflexip and Armour Plated - Casing Adaptor to be purchased Annular Diverter Location: Queensland, Australia Learn More

Make: G&K Model: 850 Engine: Caterpillar CAT 3208 (Rebuilt) Hours: 200 approx. - Replaced Extensive Hydraulic Hoses - Bean Pump on deck - 72 Metres of 4" Inch Waterbore Drill Pipe, comes with Head Tubes and Air Swivel Lots of Spares; - 2x Spare Heads -2x Spare Winches -1x Spare Wireline Drilling Capacity; 12" Inch Hole: Approx. 200 + Metres NQ: 800 Metres HQ: 600 Metres Truck Mounted Waterbore / Diamond Drill Rig Location: Victoria, Australia Learn More

Rig Make: UDR Model: 650 Onboard Compressor: Sullair 1,150 CFM / 350 PSI Air Compressor - Set up for Waterbores, RC and Aircore - Table opens up to allow 14” inch casing or bit - Recent major service of Air End, Separator Filter & New Oil - New Head Slides - New Jib Ram - New Pull Down Ropes - Head Serviced Includes; - Cyclone & Splitter - New Bull Hose - 25x Used 4” Inch RC Rods with Inner Tubes - 2x Head Tubes - Air RC Swivel - Mud Rotary Swivel - Hydraulic Breakout Arm - 4” Inch Airdrill RC Hammer (in Good Condition) & 2x Hammer Tubes - 7x 5” Inch Hammer Bits (Used) - 1x 4” Inch Back Hammer - 1x 8” Inch Aircore Bit - 4” Inch Aircore Bits (2x New & 3x Used) - Blow Up Sub - 1x 4 ½” Inch PDC Bit - 6” Inch Casing Elevator Set - Diverter Box with 20x Rubbers - Stuffing Box - Rod Spanner to suit - Dig Out Sub Rig Truck Make: Volvo Year: 2012 - Twin Steer Option 1 – Water Bore Drilling Equipment (Additional $15,400 ex GST) - 12” Inch Blade Bit (Near New) - 7 7/8” Inch Blade Bit - 8” Inch Tri-Cone Med Formation (Near New) - 6” Inch Shreps Hammer with 6” Inch & 8” Inch Bits (New) - Adaptor Subs to suit - Rod Spanners to suit - Casing Elevators Option 2 – RC Rods (Additional $55,000 ex GST) - 180 Metres of RC 4” Inch Remet Rod String (New) Option 3 – Hooklift Truck + Bins ($55,000 ex GST) Truck Make: Isuzu Year: 2000 - Hooklift Truck Bins; 1st Bin: 6x5 Gardner Denver Mud Pump with Perkins Engine 2nd Bin: To carry PVC and Gravel 3rd Bin: To carry Water Suttles Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Make: Caterpillar Model: 3406E 550 HP Engine Number: 5EK70781 Arrangement Number: 1285403 - Removed from a 1991 Kenworth T900 Truck (Done approx. 25,000 km - Diagnosed radiator was too small in the truck for a 3x trailer road train assembly) - Number 1 Cylinder has nipped up and an insurance claim was carried out by a mechanic and an exchange of a C15 fitted to truck, engine still turns over - New Cylinder Head, Injectors, and Rocker Gear with New Top and Bottom Engine Harnesses - New Exhaust Manifold, Turbo, Water Pump, Oil Cooler & Oil Squirters - New Pistons, Liners & Rods are all IPD Parts Engine Location: Northern Territory, Australia Learn More

Make: HWT Length: 6 Metre Quantity: 45 - Surepipe - Brand New Casing Location: Queensland, Australia Learn More

Make: Gertec - Brand New - Never Used Skid Mounted Grout Unit Location: Victoria, Australia Learn More

Make: Doosan Models (Suitable): PA536, XHP1250 & XHP1170 - Brand New - Tailored to meet specific requirements - Inclusive of Warranty Air End Location: Australia Learn More

Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More

Rig Model: TT300 Hours: 18 Engine: Deutz F6L912 / 66 kW Rated Depth Capacity: 300 m Feed Cylinder: 100 mm Barrel / 70 mm Shaft / 4 m Stroke Outrigger (Jacks): 4x Boxed Outriggers with 800 m Stroke Foam Pump: 21 Litre per min / 35 bar Foam/Water Tank: 120 Litre Axles: 2x 5 Tonne Air Braked Axles Tower: Direct on Cylinder / Triangle Shape Winch: 1 Tonne Push Down Force: 5,000 kgf @ 175 bar Pull Up Force: 13,000 kgf @ 175 bar Tilt Cylinders: 2x 80 Barrel 50 Shaft Breakout: 300 mm Stroke Cylinder Hydraulic Oil Tank Capacity: 330 Litres - Hydraulic Oil Cooler - Extended Tower to accommodate 4 m Stroke Cylinder - Spanners Included: 1x Breakout / 2x Keeper / 3x Hammer Modifications; - Hydraulically Tilt Rotary Head - Rotary changed to geared Rotary Head with Hollow Spindle (8,000 Nm Torque) - Including 2x Eaton Hydraulic Motors - Side Shift (on rotary head – opens up the tower for longer casing, etc.) Support Truck Make: Volvo Model: FH12 460 KM’s: 1,040,378 Type: 8x4 Air Compressor Make: Atlas Copco Model: XRV1200 Year: 2020 Hours: 122 Engine: Cummins Pressure: 22.7 bar / 330 PSI Engine/Motor Speed: 1,900 RPM Engine/Motor Power: 325 kW / 430 HP 1,200 CFM / 330 PSI - Included Drill Bits, Rods and Drilling Equipment Trailerised Drill Rig Support Truck Air Compressor Package Location: New Zealand Learn More

Mud Pump Make: Sandman Model: Mission Magnum Sandmaster 8x10x14 Year: 2017 Engine: Cummins 6 Cylinder Diesel w/ Clutch - 8 Valve Discharge Manifold on back - 2x 8 Valve Suction Manifold on each side - Flow Meter Trailer Year: 2012 - Pindle Hitch Dimensions; Width: 7.6' Length: 16' Tyres: 245/70R17.5" Trailerised Mud Pump Location: New Zealand Learn More

Make: Soilmec Model: SM-21 Year: 2010 Hours: 132 - Brand New Engine (Under Warranty) - Rebuilt Rotation Head - New Hydraulic Track Mounted Rotary Drill Rig Location: Western Australia Learn More

Rig Make: Schramm Model: 685 Year: 1996 Hours: 2,500 (Since Rebuild) Engine: Cummins K19 Accessories; - FOPS - Rod Rack - 4x Levelling Jacks - In Mast Make/Break Rod Break Out System - Rotating Cyclone Set Up on Metz Manipulator - Airdrill Maker Breaker - Air Spanner - KL Rod Handler Set to 4.5" Inch Pipe - Dual RC Swivel and Auto Blow Down - ROPS Air-Conditioned Drillers Cabin - Complete Re-Hose 11/25 - Fire Suppression Air Compressor Make: Sullair 1,150 CFM / 500 PSI Water Capacity: Approx. 500 Litres Dimensions; Height: 4.6 m Width: 4.0 m Track Mounted Drill Rig Location: Queensland, Australia Learn More

Includes; - 2x Complete Hammers (1x with a Hole Opener) - 1x Hammer in parts (Can Assemble with New Casing) - 17x Various Sized Shrouds (Mostly New) - 10x Bits (5x New & 5x Had One Run but Nearly New) - 7x Hammer Tubes - 4.5" Inch Remet to Metzke Hammer Adaptor and Inner Tubes - Various Other Spares S Reps 750 Gear Package Location: Western Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Rig Make: Hanjin Model: D&B-8D Year: 2016 Hours: 5,800 Pull: 6 Metres - 1x Set of NQ Jaws *New* - 1x Set of HQ Jaws *New* - Cameron Water Gauge *New* - Wrap Around Mast - SPT Hammer Included - Rod Racks - Suction Hose and 2x Double Braid 1" Inch Duffield Bypass Hoses - 5x 100 mm Augers and 1x Bit Plus Drive Sub - 1 1/2" Inch Centrifugal Pump and Hoses - Plus Camlocks *All New* - 36" Inch & 24" Inch Stilsons - Chain Wrench - 1.5 Metre NMLC Core Barrel Plus 5x 3 Metre NQ Rods - 2x Mud Tanks - 7x5' Foot Box Trailer Tracked Mounted Drill Rig Location: New South Wales, Australia Learn More