Search results for: 'extrapolation du classement google tg:e10838 min'

Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More

Rig Model: TT300 Hours: 18 Engine: Deutz F6L912 / 66 kW Rated Depth Capacity: 300 m Feed Cylinder: 100 mm Barrel / 70 mm Shaft / 4 m Stroke Outrigger (Jacks): 4x Boxed Outriggers with 800 m Stroke Foam Pump: 21 Litre per min / 35 bar Foam/Water Tank: 120 Litre Axles: 2x 5 Tonne Air Braked Axles Tower: Direct on Cylinder / Triangle Shape Winch: 1 Tonne Push Down Force: 5,000 kgf @ 175 bar Pull Up Force: 13,000 kgf @ 175 bar Tilt Cylinders: 2x 80 Barrel 50 Shaft Breakout: 300 mm Stroke Cylinder Hydraulic Oil Tank Capacity: 330 Litres - Hydraulic Oil Cooler - Extended Tower to accommodate 4 m Stroke Cylinder - Spanners Included: 1x Breakout / 2x Keeper / 3x Hammer Modifications; - Hydraulically Tilt Rotary Head - Rotary changed to geared Rotary Head with Hollow Spindle (8,000 Nm Torque) - Including 2x Eaton Hydraulic Motors - Side Shift (on rotary head – opens up the tower for longer casing, etc.) Support Truck Make: Volvo Model: FH12 460 KM’s: 1,040,378 Type: 8x4 Air Compressor Make: Atlas Copco Model: XRV1200 Year: 2020 Hours: 122 Engine: Cummins Pressure: 22.7 bar / 330 PSI Engine/Motor Speed: 1,900 RPM Engine/Motor Power: 325 kW / 430 HP 1,200 CFM / 330 PSI - Included Drill Bits, Rods and Drilling Equipment Trailerised Drill Rig Support Truck Air Compressor Package Location: New Zealand Learn More

Drill Rig Make: Schramm Model: T685W Year: 2007 Rig Serial Number: J124-B103 Engine: Cummins QSK19 (Hours: 500 - Brand New) Pullback Rating (Hoist Capacity): 33,884 kg Compressor: 2022 (Rebuild) Sullair DC 1,350 CFM / 500 PSI with Caterpillar C18 Compressor Hours: 3,200 (Shown) Compressor Serial Number: 200803290001 Triplex Pump: Bean 535 Pump Table Opening: 20" Inch Dual Breakouts: Metzke Hydraulic Breakout Tong Clutch: Direct Drive Set Up Rotation Head: Airdrill - Fire Suppression - Fold Down Walkways - Guarding (Spin cage with inter lock) - KL Road Loader (Hydraulic fixed) - 685WS Mast Truck Make: MAN Model: TGS 41.480 Year: 2008 KM's: 70,000 Transmission: Automatic Type: 8x8 - Mine Spec Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Rig Make: Hydrapower Model: Explorer 500 Year: 2007 Hours: 6,700 Engine: Cummins CPAK-6BTA Turbo After Cooled 6 Cylinder (176 HP @ 2,500 RPM) Rig Hydraulics; - Sauer Danfoss proportionally controlled control valves - Sauer closed loop pump on Rotary Drive Sauer open loop pump on auxiliary functions Rotary Drive; - Hydrapower Gearbox - Steel Casing with floating hollow spindle and hydraulic head lock and swing - Two Speed, 0 - 225 RPM & 0 - 966 RPM - Low speed torque to 4150 Nm - High speed torque to 966 Nm Head Travel: 6.8 m Main Winch; -Max. Pull: 4,200 kg -Max. Line Speed: 28 m/min Wireline Winch; Max. Pull: 780 kg Max. Line Speed: 83 m/min Pulldown; - Electrically controlled with dial for speed control Pull Down Capacity: 7000 kg Pull Out Capacity: 11,500 kg Mast; - Fitted with 2.0 m mast dump for angle drilling - Standard length is 10 m, supplied with hydraulically operated breakout spanner and top pulley swivel - Supplied with hydraulic circuit with quick-connect couplings for optional breakout table - Brakeout Table with Split Type Table - Bean Pump - 5x6 Gardner Denver Mud Pump (Hydraulic Driven) Truck Make: MAN Model: M2000 Year: 2005 KM's: 75,000 - Not registered - Some gearbox problems Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Make: Sandvik Model: DD420 - Was from Running Machine Condition: Good Cooler Pack Location: Western Australia Learn More

Make: Sandvik Model: DD420 Tyres: Bridgestone 12.00R20 - Typical Wear & Tear - Surface Rust on Rims - Was Removed from Running Machine Condition: Good Quantity: 4 Wheel Set Location: Western Australia Learn More

Make: Caterpillar Model: 16M Year: 2012 Hours: 10,192 Engine: Caterpillar CAT C13 Tyres: Michelin 23.5R25 - Cab A/C & Heater - Push Block - 16' Blade - MS Ripper - Mine Spec - EPA Tier 3 Motor Grader Location: Chile Learn More

Power (kW): 9-13, 30-50, 58-90, 150 Min. Flow (m3/hr): 1.5-6, 4.8-9, 8-15, 15-24 Throw (m): 30-50, 70-100, 120-150, 250 Oscillation (Deg): 0-360 Throw Angle (Deg): -5 to +45 - Stockpiles - Mine Blast Dust - Conveyor Discharge Chutes - Dust Hoppers - Crusher Machinery - Loading and Unloading Trucks - General Pollution - Airborne Dust - Construction Sites - Odor Control and Management Dust Suppression Location: Queensland, Australia Learn More

Power (kW): 9-13, 30-50, 58-90, 150 Min. Flow (m3/hr): 1.5-6, 4.8-9, 8-15, 15-24 Throw (m): 30-50, 70-100, 120-150, 250 Oscillation (Deg): 0-360 Throw Angle (Deg): -5 to +45 - Stockpiles - Mine Blast Dust - Conveyor Discharge Chutes - Dust Hoppers - Crusher Machinery - Loading and Unloading Trucks - General Pollution - Airborne Dust - Construction Sites - Odor Control and Management Dust Suppression Location: Queensland, Australia Learn More

Drill Rig Make: Chicago Pneumatic Model: CP650 Year: 1981 Engine: Caterpillar CAT 3406 Onboard Air Compressor: GHH 825 CFM / 350 PSI Twin Screw Injection Pump: Comet APS 71 ltr/min @ 580 PSI Casing Driver: 612 Banger 6" Inch - 12" Inch Winch: 1/2" Inch 7,000 lbs Extendable Rod Handling Jib Hole Capacity: 6" Inch - 12" Inch 500 m 4 1/2" Inch Rods Capacity; Pull Down: 21,000 lbs Pull Back: 55,000 lbs 5 1/2" Inch Heavy Hoist Rams 73 ft/min Rapid Feed - 160 Pitch Chains Levelling Jacks; Front: 1 x 5" Inch x 48" Inch Stroke Rear: 2 x 5" Inch x 36" Inch Stroke Top Drive Rotary; 0-152 RPM - 76,000 lb Torque Twin Dynex Motors R/C Head - 7 m Travel Carrier Type: 6x4 Engine: Caterpillar CAT 3208 @ 210 HP Crane Carrier Carrier Mounted Water Well Drill Rig Location: New Zealand Learn More

Engine: Deutz 3FL2011 - Base Frame to support all components; engine, pump, hydraulics & fuel tanks, etc. - Fuel Tank Capacity: 60 Litres - Access Ladder to Control Platform - Paint, Two Pack Evolution Yellow Hydraulics; - Pump Group Bosch Rexroth - Main Pump A10VO45 Variable Displacement - Pilot Pump 5.5 cc Gear Pump - Maximum Circuit Pressure: 160 Bar - Hydraulic Oil Capacity: 100 Litres - Return Filter: 10 Micron - Hydraulic Oil Cooler and Fan Grout Pump; Make: Bredel Model: SPX 50 - Brevini BR100NC Hydraulic Motor - Slurry Flow Range: 0-85 lpm - Maximum Pressure: 15 Bar - Adjustable Speed Control Mixing Tank; Capacity: 1,400 Litres - Hydraulic Powered Agitator - Baffle Plates inside the tank - 3" Inch Outlet to Slurry Pump - Grid on tank top for cement dispersion during mixing - Sandblasted and painted with 2 pack paint Poly Reel; Capacity: 600 metres - 40 mm PN16 SDR11 Poly Pipe, Blue Stripe, 3.7 mm Wall - Fabricated construction approx. 2.1 metres diameter - Hydraulic Drive via reduction gearbox and chain + sprocket final drive - Adjustable Speed Control: 1.5-30 m/min Control Platform; - Mounted near mixing tank - Engine controls, start, stop, throttle, etc. - Hydraulic controls for agitator, slurry pump and hose reel Dimensions; Length: 4.65 m Width: 2.35 m Hight: 2.5 m Weight: 3,500 kg approx. Skid Mounted Grouting Unit Location: Australia Learn More

Model: FH3000 Engine: Cummins QSL Electronic @ 255 kW (342 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Maximum Speed: 55.5 m/min (182 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - 100% Theoretical Main Winch; - Maximum Pull: 226 kN (50,806 lbf) - Maximum Speed: 100 m/min (328 ft/min) - 2x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release - 9 Metre Rod Pull Capacity Wireline Winch; - Maximum Pull: 27 kN (6,069 lbf) - Rope Capacity: 3,000 Metres x 8 mm Rope - Maximum Speed: 450 m/min (1,476 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH2000 Engine: Caterpillar CAT C7.1 Electronic @ 205 kW (275 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Up: 50 m/min (164 ft/min) Down: 39 m/min (128 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - Bosch Rexroth A6VM160 Variable Displacement Motor - High Gear 3:1 & Low Gear 19.57:1 ratios - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube Bearings and Gears with filtered and cooled lubrication oil system Main Winch; - Maximum Pull: 156 kN (35,048 lbf) - 120 m/min (394 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - 28 mm Main Winch Rope - Safety Factor 3.35:1 (exceeds BS/EN791) - 1x Bosch Rexroth A6VM160 Variable Displacement Motors - 1x Brevini Planetary Reduction Gear Boxes - 1x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release Wireline Winch; - Mast Mounted - Maximum Pull: 25 kN (5,617 lbf) - Rope Capacity: 2,100 Metres x 8 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1300 Engine: Caterpillar CAT C7.1 Electronic @ 187 kW (250 HP) Pull Back: 115 kN (25,853 lbf) Actual Pull Down: 70 kN (15,736 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 1,300 m HQ Core: 885 m Open Hole 3 1/2" Inch Rods: 380 m RC 4 1/2" Inch: 220 m (Nominal) Traverse Speed; Up: 60 m/min (196.8 ft/min) Down: 56 m/min (183.7 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 8,087 Nm (6,111 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - High Gear 3.04:1 & Low Gear 12.61:1 ratios - Variable Displacement 160cc Hydraulic Motor - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube System with Cooler and Filter Main Winch; - Maximum Pull: 100 kN (10,000 lbf) - 120 m/min (393 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - Main Winch Rope - Safety Factor to Meet BS/EN791 - Planetary Reduction Gear Box & Brake - Variable Displacement Hydraulic Motor Drive Wireline Winch; - Deck Mounted - Maximum Pull: 15 kN (3,372 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1000 Pull Back: 97 kN (21,783 lbf) Pull Down: 45 kN (10,116 lbf) Water Pump: Standard FMC W1122BCD 140 lpm @ 1,000 psi Depth Capacity; NQ Core: 1,150 m HQ Core: 786 m HWT Core: 518 m RC 4" Inch: 198 m (Nominal) Engine Options; - John Deere Power Tech 6.8L @ 155 kW (208 HP) - Caterpillar CAT C6.6 ACERT - Cummins B5.9-173 Traverse Speed; Up: 47 m/min (154 ft/min) Down: 30 m/min (98 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 5,965 Nm (4,400 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - 100% Theoretical Main Winch; - Maximum Pull: 88.4 kN (19,870 lbf) - 55 m/min (180 ft/min) - Mast Top Mounted - 1x Multi Disc Brake Unit - Fail Safe Spring Activated - Hydraulic Pressure Release - Main Winch Rope - Safety Factor to Meet BS/EN791 - 6 Metre Rod Pull Capacity Wireline Winch; - Deck Mounted - Maximum Pull: 13.5 kN (3,044 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Maximum Speed: 342 m/min (1,124 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Make / Model: TL-400 Contains: - Tower - Flashlight - Headlight - Charger - Driver - Battery System D24-100 - USD Output, 5V 2A (2 Dock) for charging Headlight, Flashlight or Mobile Phone - 1-3 Battery Pack (1 Battery 30+ Hours extreme mode) - Height: 64.5 cm - 220 cm - Weight: 12.85 kg - One Man Operation - Self locking and 30 degree + up/down adjustable pole - Run Times > 10 hours (High output, 3 batteries) Application - Drilling - Construction - Maintenance - Events - Mining - Emergency - Infrastructure - Personal Control Board - Power Switch - Brightness - DIM+, DIM- - Battery Level - AC Plug - USB Output Light Brightness Area: 1,100 m2 5 m - 490 lux / 10 m - 120 lux / 20 m - 29 lux / 40 m - 7 lux Battery / AC 100-227V - AC 0-15,000 LM - High 8,000 LM - Medium 5,000 LM - Low 2,500 LM - Extreme 800 LM - Rate Power 28 wh - Rate Voltage 24.5 V - Rate Capacity 40 Ah - Working Temp: -10 to 50 degrees - Working Humidity: -20 to 95% Portable Light Tower Location: Queensland, Australia Learn More

Make: Cubex Model: QXR 920 Year: 2004 (Rebuild 2019) Hours: 16,896 Engine: Caterpillar CAT C15 Rotary Head: Cubex @ 6,230 hours (Rebuilt May 2019) Rotation Torque: 5,730 Nm Rotation Speed: 0-80 RPM Variable Jaw Rotation: 15 degrees Clamping Force: 288 kN Carousel Capacity: 6 Rods Max. Rod Size: 5" Inch Min. Rod Size: 3.25 " Inch Rod Length: 6 m / 20 ft Onboard Air Compressor: Sullair + Spares Included Track Mounted Surface Drill Rig Location: Western Australia Learn More

Make: Custom Model: 600 RRD Motor: 40 HP TEFC Pulling Capacity: 24,000 lbs Lifting Capacity: 24,000 lbs Down Thrust Capacity: 12,500 lbs Rotational Torque: 6,500 ft/lbs Load Sensing Power Limiting Pump: 45 GPM @ 1,700 PSI Load Sensing Diesel Pump: 15 GPM @ 3,500 PSI Fast Feed: 14.79 GPM @ 2,500 PSI Slow Feed: 6.2 GPM @ 2,500 PSI Traction Hydraulic Motor: 14 HP each at 4,000 MASL (Using Diesel Drive) Max. Drilling Air Pressure: 400 PSI Feed Cylinders Combined Bore: 9.8 sq inch Features; - Lubricator - Water Pump - Robust Mine Proven Construction - High Torque Rotation Head - Reversable Heavy Duty Mast - Efficient Electric/Hydraulic Drive - Fully Hydraulic Operation - Compact Size - Fully Variable Rotation Speed (0-24 RPM) Hydraulically Operated Crawlers - Remotely Operated Hydraulic Console for flexibility - Sting Cylinder - Dual Heavy Duty Feed System - 90 Degree Tilt Out Rotation Head - Longitudinal Shift - Side Shift - NEMA 4 - Air Motors for travelling Track Mounted Drill Rig Location: Canada Learn More

Make: Sandvik Model: DR560/80 Hours: Various Max Feed Rate: 1.3 m/s (257 ft/min) Max Hoisting @ 2,100 RPM: 47 kN (10,600 lbf) Max Pulldown @ 2,100 RPM: 47 kN Top Drive Rotation Torque: 5,730 Nm Rotation Speed: 0-80 RPM (Variable) Carousel Standard Capacity: 6 Rods (5 Rods for OD 140 mm (5.5" inch) Max Rod Size: 140 mm / 5.5" inch Min Rod Size: 89 mm / 3.5" inch Rod Length: 6.1 m / 20 ft Min Hammer Size: 102 mm / 4" inch Carousel Hole Depth: 42.6 m / 140 ft Max Hole Size: 216 mm / 8.5" inch Min Hole Size: 115 mm / 4.5" inch + More information can be provided Track Mounted Contour DTH Drill Rig Location: Western Australia Learn More

Max Pressure: 200PSI - Diesel Engine - 12HP - 120-200 L/min flow Weight: 120 kg Lightweight Portable Mud Pump Location: New South Wales, Australia Learn More