Search results for: 'high for site in johnson case tx'

Make: Brevini Year: 2017 Hours: 0 (Complete Overhaul in June 2025) Weight: 1,650 kg - All Hydraulics and Electrics have been fully re-conditioned - 55kW Electric Motor driving a hydraulic pump, which in turn drives a reciprocating high pressure water pump with a maximum output of 90L/min of water at 180 Bar pressure. - The complete pump system has been designed to run continuously and all equipment is housed within a fully enclosed cover. - As the motor drives a hydraulic pump, the high pressure water output is fully adjustable while the motor runs at a constant speed, unlike a high pressure water pump that is direct driven by a fixed speed electric motor. Additionally, because the hydraulic circuit incorporates an unloader valve, it is possible to switch the high pressure water on and off without the need to stop the motor or bypass high pressure water into a holding tank. - The hydraulics system is of robust construction containing 300L of oil and an integrated oil cooler. - The system can also be used as a 55 kW hydraulic power pack. Skid Mounted Pump Location: Queensland, Australia Learn More

Sizes: 3" Inch / 4" Inch / 5" Inch Working Pressure: 2,500 PSI - Basic Hard Shut in Nitrile Bladder - Wireline Stripper - Hydraulic Activator - Hand Pump Activator - All Hoses Burst Protection or Fire Protected - Zone One Hoses are Coflexip and Armour Plated - Casing Adaptor to be purchased Annular Diverter Location: Queensland, Australia Learn More

Rig Make: UDR Model: 650 Onboard Compressor: Sullair 1,150 CFM / 350 PSI Air Compressor - Set up for Waterbores, RC and Aircore - Table opens up to allow 14” inch casing or bit - Recent major service of Air End, Separator Filter & New Oil - New Head Slides - New Jib Ram - New Pull Down Ropes - Head Serviced Includes; - Cyclone & Splitter - New Bull Hose - 25x Used 4” Inch RC Rods with Inner Tubes - 2x Head Tubes - Air RC Swivel - Mud Rotary Swivel - Hydraulic Breakout Arm - 4” Inch Airdrill RC Hammer (in Good Condition) & 2x Hammer Tubes - 7x 5” Inch Hammer Bits (Used) - 1x 4” Inch Back Hammer - 1x 8” Inch Aircore Bit - 4” Inch Aircore Bits (2x New & 3x Used) - Blow Up Sub - 1x 4 ½” Inch PDC Bit - 6” Inch Casing Elevator Set - Diverter Box with 20x Rubbers - Stuffing Box - Rod Spanner to suit - Dig Out Sub Rig Truck Make: Volvo Year: 2012 - Twin Steer Option 1 – Water Bore Drilling Equipment (Additional $15,400 ex GST) - 12” Inch Blade Bit (Near New) - 7 7/8” Inch Blade Bit - 8” Inch Tri-Cone Med Formation (Near New) - 6” Inch Shreps Hammer with 6” Inch & 8” Inch Bits (New) - Adaptor Subs to suit - Rod Spanners to suit - Casing Elevators Option 2 – RC Rods (Additional $55,000 ex GST) - 180 Metres of RC 4” Inch Remet Rod String (New) Option 3 – Hooklift Truck + Bins ($55,000 ex GST) Truck Make: Isuzu Year: 2000 - Hooklift Truck Bins; 1st Bin: 6x5 Gardner Denver Mud Pump with Perkins Engine 2nd Bin: To carry PVC and Gravel 3rd Bin: To carry Water Suttles Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Make: Austex Model: 5.5" Inch Cup Upgrade DD 4.5" Inch Type: PQ Jaw in Pelican Case Jaw Kit Location: Northern Territory, Australia Learn More

Make: Ozcon Size: 12-3/4" Inch Length: 6 Metre Quantity: 7 Casing Location: Queensland, Australia Learn More

Size: 5-9/16" Inch Length: 6 Metre Quantity: 25 Casing Location: Queensland, Australia Learn More

Make: HWT Length: 6 Metre Quantity: 45 - Surepipe - Brand New Casing Location: Queensland, Australia Learn More

OD: 180mm ID: 160mm Length: 6 Metre Quantity: 20 Seamless Casing Location: Queensland, Australia Learn More

Drill Rig Make: American Augers Model: DD140 Control Room Capacity: 20’ Foot Storeroom Capacity: 10’ Foot Genset Make: Kubota Model: GL9000D-AU-B Serial No: K10450 Capacity: 9kVA Control Room Trailer Make: Krueger Model: ST338 Year: 2008 ATM: 38 Tonne VIN: 6FH9079AB8M012264 - Trailer Pipe Handler Trailer Make: Gallagher Year: 2024 Max. Lifting Capacity: 1,100 kg - Purpose built Tandem Axle Trailer on airbag suspension with EBS braking - 4x Hydraulic Jack Legs - Self-Contained other than using the DD140 Auxiliary Hydraulics - Can present Horizontal Rod/Casing/BHA from a rod bench & install into the machine - Supplied with requested dies to suit rods, casing & BHA equipment - Full operational dash, with E-Stops on various positions - Complete working deck between the rig & road loader Including; - Rig Sub Base and Drill Floor Not Included; - Koomey Unit (in Photos) Track Mounted Drill Rig Package Location: Queensland, Australia Learn More

Make: Nissan Model: Patrol DX GU MY08 Year: 2009 KM's: 282,381 Transmission: 5 Speed Manual Type: 4x4 - New Engine at 241,000 km's - Clutch and Flywheel - 3" Inch Exhaust - Long Range Tank - Water Tank - 2x Spare Tyres - Full Mine Spec (inc. UHF, High Vis, etc.) Ute Location: Western Australia Learn More

Rig Model: TT300 Hours: 18 Engine: Deutz F6L912 / 66 kW Rated Depth Capacity: 300 m Feed Cylinder: 100 mm Barrel / 70 mm Shaft / 4 m Stroke Outrigger (Jacks): 4x Boxed Outriggers with 800 m Stroke Foam Pump: 21 Litre per min / 35 bar Foam/Water Tank: 120 Litre Axles: 2x 5 Tonne Air Braked Axles Tower: Direct on Cylinder / Triangle Shape Winch: 1 Tonne Push Down Force: 5,000 kgf @ 175 bar Pull Up Force: 13,000 kgf @ 175 bar Tilt Cylinders: 2x 80 Barrel 50 Shaft Breakout: 300 mm Stroke Cylinder Hydraulic Oil Tank Capacity: 330 Litres - Hydraulic Oil Cooler - Extended Tower to accommodate 4 m Stroke Cylinder - Spanners Included: 1x Breakout / 2x Keeper / 3x Hammer Modifications; - Hydraulically Tilt Rotary Head - Rotary changed to geared Rotary Head with Hollow Spindle (8,000 Nm Torque) - Including 2x Eaton Hydraulic Motors - Side Shift (on rotary head – opens up the tower for longer casing, etc.) Support Truck Make: Volvo Model: FH12 460 KM’s: 1,040,378 Type: 8x4 Air Compressor Make: Atlas Copco Model: XRV1200 Year: 2020 Hours: 122 Engine: Cummins Pressure: 22.7 bar / 330 PSI Engine/Motor Speed: 1,900 RPM Engine/Motor Power: 325 kW / 430 HP 1,200 CFM / 330 PSI - Included Drill Bits, Rods and Drilling Equipment Trailerised Drill Rig Support Truck Air Compressor Package Location: New Zealand Learn More

Rig Make: Hydrapower Model: Explorer 500 Year: 2007 Hours: 6,700 Engine: Cummins CPAK-6BTA Turbo After Cooled 6 Cylinder (176 HP @ 2,500 RPM) Rig Hydraulics; - Sauer Danfoss proportionally controlled control valves - Sauer closed loop pump on Rotary Drive Sauer open loop pump on auxiliary functions Rotary Drive; - Hydrapower Gearbox - Steel Casing with floating hollow spindle and hydraulic head lock and swing - Two Speed, 0 - 225 RPM & 0 - 966 RPM - Low speed torque to 4150 Nm - High speed torque to 966 Nm Head Travel: 6.8 m Main Winch; -Max. Pull: 4,200 kg -Max. Line Speed: 28 m/min Wireline Winch; Max. Pull: 780 kg Max. Line Speed: 83 m/min Pulldown; - Electrically controlled with dial for speed control Pull Down Capacity: 7000 kg Pull Out Capacity: 11,500 kg Mast; - Fitted with 2.0 m mast dump for angle drilling - Standard length is 10 m, supplied with hydraulically operated breakout spanner and top pulley swivel - Supplied with hydraulic circuit with quick-connect couplings for optional breakout table - Brakeout Table with Split Type Table - Bean Pump - 5x6 Gardner Denver Mud Pump (Hydraulic Driven) Truck Make: MAN Model: M2000 Year: 2005 KM's: 75,000 - Not registered - Some gearbox problems Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Includes; - 2x Complete Hammers (1x with a Hole Opener) - 1x Hammer in parts (Can Assemble with New Casing) - 17x Various Sized Shrouds (Mostly New) - 10x Bits (5x New & 5x Had One Run but Nearly New) - 7x Hammer Tubes - 4.5" Inch Remet to Metzke Hammer Adaptor and Inner Tubes - Various Other Spares S Reps 750 Gear Package Location: Western Australia Learn More

Power (kW): 9-13, 30-50, 58-90, 150 Min. Flow (m3/hr): 1.5-6, 4.8-9, 8-15, 15-24 Throw (m): 30-50, 70-100, 120-150, 250 Oscillation (Deg): 0-360 Throw Angle (Deg): -5 to +45 - Stockpiles - Mine Blast Dust - Conveyor Discharge Chutes - Dust Hoppers - Crusher Machinery - Loading and Unloading Trucks - General Pollution - Airborne Dust - Construction Sites - Odor Control and Management Dust Suppression Location: Queensland, Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Power (kW): 9-13, 30-50, 58-90, 150 Min. Flow (m3/hr): 1.5-6, 4.8-9, 8-15, 15-24 Throw (m): 30-50, 70-100, 120-150, 250 Oscillation (Deg): 0-360 Throw Angle (Deg): -5 to +45 - Stockpiles - Mine Blast Dust - Conveyor Discharge Chutes - Dust Hoppers - Crusher Machinery - Loading and Unloading Trucks - General Pollution - Airborne Dust - Construction Sites - Odor Control and Management Dust Suppression Location: Queensland, Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Type: DCS-S 4-4.7/8" Inch - Comes with 1x Set of Inserts Drilling Collar Slips Casing Slip Bowls Location: Queensland, Australia Learn More

Rig Make: Edson Model: Versadrill 300 Year: 1996 Engine: Hatze - 6x6 Multidrive Technology - Rotation head MR260 Rotation hollow spindle, single speed, dial in, rotation head around 120 rpm - Winching gear on back of mast for hollow augering - Can do diamond drilling if you were to change the hydraulic motor - Dump Mast - Near New Hydraulic Pump - 4x Leveling Jacks - Currently doing 80mtr holes at 4.5” - Client used to aircore with it, but currently set up doing mud - Used to do a lot of Geotech work, 6” hollow augering - Southern Cross Mud pump on the side - 3.2 mtr Stroke - 3 mtr Rods - Extension arm to run 6mtr casing into the ground Ute Make: Toyota Model: Landcruiser Year: 1990 KM's: 107,000 Ute Mounted Drill Rig Location: Western Australia Learn More

Make: National Oilwell Varco NOV Model: CRT350/500 FAC-Tool Casing Running Tool Location: Queensland, Australia Learn More