Search results for: 'hole for skid 1998'

Make: Hydco Model: 8V92 Year: 2021 Hours: 7,370 - New Air Side at 500 hours - Pistons, Rings, Barrels, etc. all out of Hydco - New Blower fitted in December with 60 hours - New Fuel Rack and Tune Up completed - Spare PRV's 1,800 CFM 900 PSI Skid Mounted Booster Location: Northern Territory, Australia Learn More

Make: Weir Minerals Model: MHD-100HV Rated RPM: 186 kW @ 2,200 RPM Suction Diameter: 150 mm Discharge Diameter: 200 mm Suction Flange: 406 OD x 200 ID 8 Holes 21 Dia. On 356 PCD Discharge Flange: 368 OD x 150 ID 8 Holes 21 Dia. On 324 PCD - Hydraulic Powered Highwall Pump Unit Location: Western Australia Learn More

Make: Weir Minerals Model: MHD-100HV Rated RPM: 186 kW @ 2,200 RPM Suction Diameter: 150 mm Discharge Diameter: 200 mm Suction Flange: 406 OD x 200 ID 8 Holes 21 Dia. On 356 PCD Discharge Flange: 368 OD x 150 ID 8 Holes 21 Dia. On 324 PCD - Hydraulic Powered Highwall Pump Unit Location: Western Australia Learn More

Engine: Yanmar 4TNV88-DSA - Diesel Driven Skid Mounted Hydraulic Cable Pulling Unit Location: Queensland, Australia Learn More

Make: Sullair Model: 900/1150XH Year: 2006 Skid Mounted Air Compressor Location: Western Australia Learn More

Make: Black Diamond Model: HJGCXT 08 Year: 2023 Type: 3.5" Inch - 10" Inch Skid Mounted Hammer Breakout Unit Location: Queensland, Australia Learn More

Make: Custom Made Model: GT500 Year: 1997 Dimensions; Length: 2 Metres Width: 1.5 Metres Height: 1.2 Metres Weight: 680 kg each Bowl Capacity: 500 Litres each - Mazda Power Packs or larger most suitable for these mixers - Last Used approx. 2014 - Controlled Independently - Specifically designed to mix large volumes of High Early Strength Non-Shrink Grouts very quickly - Cycle times were designed to be less than eight minutes and continuously - Indeed full truckloads of fast setting grouts were mixed and placed using these machines in less than a shift - Mixers were commonly mounted and used from the back of our truck - There are two mixers; a left hand and a right hand - When used together the controls were in the centre between the mixers - When configured like this one operator would control both machines - One machine would be dumping while the other one was mixing - Output was continuous and in less than eight minutes per batch - Mixed grout was dumped into a hopper and taken to the site needed - Forklift Channels (Center Balanced) - Machine has mixed; Proprietary Cement Grouts, Non-Shrink Grouts, Small Aggregate Concrete, etc. - Hydraulic Driven Skid Mounted Grout Mixers & Hoppers Location: Queensland, Australia Learn More

Unit #1 Make/Model: Custom Made Year: 1995 KM’s: 40,000 Power Pack Hours: 140 Engine: Mazda Diesel 4 Cylinder Dual Fixed Displacement Hydraulic Power Pack Dimensions; Length: 2.2 Metres Width: 1.1 Metres Height: 1.1 Metres Weight: 1,060 kg - Last Started July 2025 - No Batteries (24 Volt System) - Fixed Displacement Pump @ 32cc per rev with Working Pressure @ 2,500 PSI. - Fitted with a Piggy Back - Fixed Displacement Pump @ 11cc per rev with Working Pressure @ 2,500 PSI - All Safety Guards Available - Compliance Labelled - Gauges: Oil Pressure, Fuel Gauge, Hour Meter, Charge, Battery Isolation Lock Out, etc. - Emergency Stop Switch - Throttle - Key Start - Forklift Channels (Center Balanced) - Crane Lifting Eyes on Corners Unit #2 Make/Model: Custom Made Year: 1995 KM’s: Less than 40,000 Power Pack Hours: 51 Engine: Mazda Diesel 4 Cylinder Variable Displacement Hydraulic Power Pack Dimensions; Length: 2.2 Metres Width: 1.1 Metres Height: 1.1 Metres Weight: 1,060 kg - Last Started July 2025 - No Batteries (24 Volt System) - Fixed Displacement Pump @ 45cc per rev with Working Pressure @ 2,500 PSI. - All Safety Guards Available - Compliance Labelled - Gauges: Oil Pressure, Fuel Gauge, Hour Meter, Charge, Battery Isolation Lock Out, etc. - Emergency Stop Switch - Throttle - Key Start - Forklift Channels (Center Balanced) - Crane Lifting Eyes on Corners Quantity: 2 Skid Mounted Hydraulic Power Units Location: Queensland, Australia Learn More

Make: Everdigm Model: Rocky B180 Bit Shank: N180 Shank Connection: API 8-5/8" Inch Reg. Pin Piston Stroke: 5.75" Inch Cylinder Bore: 12.28" Inch Hole Sizes: 18" Inch ~ 26" Inch Wrench Size: A/F 14" Inch - Brand New - Bailing Subs/Break Out Plate, etc. - Hammer forklift cradle included - 19” Hammer bit included (unused) RS Hammer Location: Queensland, Australia Learn More

Rig Make: Hanjin Model: D&B-8D Year: 2016 Hours: 5,800 Pull: 6 Metres - Warman Clamps - Under Casing Clamps - Wireline and Main Winch - Rod Bin - Auger Carrying Rack at Front of Rig - Auto SPT - Silvan Pump - All New Suction and Hydraulic Hoses for Pump with Camlocks - 2x Mud Tanks (1,000 L & 500 L - Plastic) Down Hole Gear - 10x 3m PQ Rods Plus Shorts - 10x 3m HQ Rods Plus Shorts - 10x 3m NQ Rods Plus Shorts - 10x 3m Junior Mayhew Rods with Spanner Flats Plus 2x 1.5 m - 5x 100mm x 1.5m Augers Plus Bit & 20 Pins - 2x 1.5 NMLC Core Barrels - 6x NMLC Core Bits - 4x Impreg & 2x Surface Set - 40x Core Lifters / 6x Cases / 40x Stop Rings - 2x NMLC Reamers - 2x BQ Reamers - 3x BQ Core Bits - 2x 1.5m NQ3 Core Barrels - 2x Sets of Splits - 1x 3m NQ3 Core Barrel - 2x Locking Couplings - 2x Adaptor Couplings - Box of Barrel Spares - 1x HQ/NQ Overshot - 1x Set of PQ, HQ, NQ Inner Tube Wrenches - 10x 75mm Shelby Tubes Plus Drive Head - 10x 50mm Shelby Tubes Plus Drive Head - 2x SPT Samplers - 2x Pulling Plugs - 1x Spare Water Swivel Plus 2x Repair Kits - 1x Repair Kit for Rig Swivel - Many Subs to Facilitate all the Drilling Requirements - Stillsons - 2x 36" Inch, 2x 24" Inch & 2x 18" Inch - 1x Gas Mig Welder - 1x Honda 3.5 kVA Powered Generator - 1x PQ Birds Mouth for Water Return to Mud Tanks - 1x HQ Birds Mouth for Water Return to Mud Tanks - New Suction and Delivery Hoses - 1x 100mm Down Hole Hammer with 2x Bits 118mm *New* - 1x 75mm Down Hole Hammer with 2x Bits 95mm *New* Support Truck Make: Mitsubishi Model: Canter Year: 2009 Type: 4x4 - Hydraulic Hi-Ab Crane - 500 Litre Water Tank - 400 Litre Diesel Tank for Rig & 12 Volt Pump - 1x kVA Inverter - Wired so diesel pump won't engage until the switch is turned on in the locked tool box. - 1x Centrifugal Pump 1 1/2" Inch plus Suction and Delivery Hoses with Camlocks - 2x Tool Boxes - 1x Box of Hand Spanners & Sockets - Fitted Drill Rod Bins & Core Barrel Bins - Currently Registered until May 2025 Tracked Mounted Drill Rig Support Truck + Down Hole Gear Package Location: New South Wales, Australia Learn More

Make: Brevini Year: 2017 Hours: 0 (Complete Overhaul in June 2025) Weight: 1,650 kg - All Hydraulics and Electrics have been fully re-conditioned - 55kW Electric Motor driving a hydraulic pump, which in turn drives a reciprocating high pressure water pump with a maximum output of 90L/min of water at 180 Bar pressure. - The complete pump system has been designed to run continuously and all equipment is housed within a fully enclosed cover. - As the motor drives a hydraulic pump, the high pressure water output is fully adjustable while the motor runs at a constant speed, unlike a high pressure water pump that is direct driven by a fixed speed electric motor. Additionally, because the hydraulic circuit incorporates an unloader valve, it is possible to switch the high pressure water on and off without the need to stop the motor or bypass high pressure water into a holding tank. - The hydraulics system is of robust construction containing 300L of oil and an integrated oil cooler. - The system can also be used as a 55 kW hydraulic power pack. Skid Mounted Pump Location: Queensland, Australia Learn More

Make: Gardner Denver Model: SCH2500 Year: 1990 approx. Engine: Cummins 6 BTA 5.9 Serial Number: 2711468 - Includes Drill Rods and Sampling Equipment Complete Overhaul; - Hammer HPRI - New Head Injectors on Fuel Pump - Track and Final Drives - Oil Cooler Replaced with CAT Cooler and mounted on left hand side Hydratrack Track Mounted Blast Hole Drill Rig Location: Queensland, Australia Learn More

Model: HT400 Engine: Cummins Transmission: Alison Gearbox - Variable Speed - 450 to 500 GPM Skid Mounted Triplex Mud Pump Location: Queensland, Australia Learn More

Make: Elgi Year: 2023 Hours: 364 - Like New 900 CFM 350 PSI Skid Mounted Air Compressor Location: Queensland, Australia Learn More

Make: G&K Model: 850 Engine: Caterpillar CAT 3208 (Rebuilt) Hours: 200 approx. - Replaced Extensive Hydraulic Hoses - Bean Pump on deck - 72 Metres of 4" Inch Waterbore Drill Pipe, comes with Head Tubes and Air Swivel Lots of Spares; - 2x Spare Heads -2x Spare Winches -1x Spare Wireline Drilling Capacity; 12" Inch Hole: Approx. 200 + Metres NQ: 800 Metres HQ: 600 Metres Truck Mounted Waterbore / Diamond Drill Rig Location: Victoria, Australia Learn More

Make: Sandvik Drilltech Model: D75KS Engine: Caterpillar CAT 3412 - 2 x Rotation Heads (One still on mast) - Complete Mast (New Generation) - Air End - Air Receiver - Newly Rebuilt Drifter Track Mounted Rotary Blast Hole Drill Rig Location: Northern Territory, Australia Learn More

- Has Jack Up Leg Holes (No Legs) Length: 6 Metre Rod Sloop Location: Queensland, Australia Learn More

Make: Mosa Model: DSP 400 YSX-PL Skid Mounted Welder Location: Queensland, Australia Learn More

Make: Gertec Model: IS-38-E Serial Number: 44390 Skid Mounted Grout Unit Location: Victoria, Australia Learn More

Make: Gertec - Brand New - Never Used Skid Mounted Grout Unit Location: Victoria, Australia Learn More