Search results for: 'boart gear high for state'

Make: Caterpillar Model: 16 GC Year: 2021 Hours: 5,700 - Sold Offshore Motor Grader Location: United States of America Learn More

Model: HD-500 Engine: Detroit 8V-92TA / 450HP @ 2,100 RPM Flow Rate: Up to 7.5 BPM / 315 GPM / 1,200 LPM High Pressure: Up to 13,500 PSI Dimensions; Length: 6,058 mm Width: 2,438 mm Height: 2,591 mm Weights; Unit Weight: 11,000 kg Frame Max: 15,000 kg Stacking Mass: 194,000 kg Skid Mounted Triplex Pump Unit Location: United Arab Emirates Learn More

Make: Caterpillar Model: 825G Year: 2003 Hours: 10,356 Soil Compactor Location: United States of America Learn More

Make: Caterpillar Model: 773G Year: 2014 Hours: 23,585 Idle Hours: 13,606 - New Tank - 3x Adjustable Rear Spray Heads - 2x Side Spray Heads - Hose Reel - Water Cannon - Top Fill Water Truck Location: United States of America Learn More

Drill Rig Make: Boart Longyear Model: LF160C Year: 2020 Installed Power: 194 kW Working Pressure: 380 bar Head Torque: 665 I / 90 II daNm Head Rotation: 250 I / 1,050 II RPM Feed Force: 7,000 daN Retract Force: 17,000 daN Feed Length: 7,200 mm Tracks Make: Strickland Track Mounted Drill Rig Location: Queensland, Australia Learn More

Drill Rig Make: Boart Longyear Model: LF160C Year: 2022 Installed Power: 194 kW Working Pressure: 380 bar Head Torque: 665 I / 90 II daNm Head Rotation: 250 I / 1,050 II RPM Feed Force: 7,000 daN Retract Force: 17,000 daN Feed Length: 7,200 mm Tracks Make: Strickland Model: 6000428 Year: 2022 Track Mounted Drill Rig Location: Queensland, Australia Learn More

Rig Make: Hanjin Model: D&B-8D Year: 2016 Hours: 5,800 Pull: 6 Metres - Warman Clamps - Under Casing Clamps - Wireline and Main Winch - Rod Bin - Auger Carrying Rack at Front of Rig - Auto SPT - Silvan Pump - Repair Kit for Silvan Pump - All New Suction and Hydraulic Hoses for Pump with Camlocks - 2x Mud Tanks (1,000 L & 500 L - Plastic) - 1x 7x5 Trailer with Fold Out Canopy + 12 Volt Fridge & Esky (In a locked container) - 2x Gas Bottles & Cookers (Mounted on Front of Trailer) - 2x 20 Litre Water Containers (Mounted on Front of Trailer) Down Hole Gear - 10x 3m PQ Rods Plus Shorts - 10x 3m HQ Rods Plus Shorts - 10x 3m NQ Rods Plus Shorts - 10x 3m Junior Mayhew Rods with Spanner Flats Plus 2x 1.5 m - 5x 100mm x 1.5m Augers Plus Bit & 20 Pins - 2x 1.5 NMLC Core Barrels - 6x NMLC Core Bits - 4x Impreg & 2x Surface Set - 40x Core Lifters / 6x Cases / 40x Stop Rings - 2x NMLC Reamers - 2x BQ Reamers - 3x BQ Core Bits - 2x 1.5m NQ3 Core Barrels - 2x Sets of Splits - 1x 3m NQ3 Core Barrel - 2x Locking Couplings - 2x Adaptor Couplings - Box of Barrel Spares - 1x HQ/NQ Overshot - 1x Set of PQ, HQ, NQ Inner Tube Wrenches - 10x 75mm Shelby Tubes Plus Drive Head - 10x 50mm Shelby Tubes Plus Drive Head - 2x SPT Samplers - 2x Pulling Plugs - 1x Spare Water Swivel Plus 2x Repair Kits - 1x Repair Kit for Rig Swivel - Many Subs to Facilitate all the Drilling Requirements - Stillsons - 2x 36" Inch, 2x 24" Inch & 2x 18" Inch - 1x Gas Mig Welder - 1x Honda 3.5 kVA Powered Generator - 1x PQ Birds Mouth for Water Return to Mud Tanks - 1x HQ Birds Mouth for Water Return to Mud Tanks - New Suction and Delivery Hoses - 1x 100mm Down Hole Hammer with 2x Bits 118mm *New* - 1x 75mm Down Hole Hammer with 2x Bits 95mm *New* - 2x 1.5m HQ3 Core Barrels - 2x 3m HQ3 Outer & Inner Splits - 1x 3m NQ3 Outer & Inner Splits - 4x HQ3 Core Bits - 20x HQ3 Core Lifters, Stop Rings & Cases Support Truck Make: Mitsubishi Model: Canter Year: 2009 Type: 4x4 - Hydraulic Hi-Ab Crane - 500 Litre Water Tank - 400 Litre Diesel Tank for Rig & 12 Volt Pump - 1x kVA Inverter - Wired so diesel pump won't engage until the switch is turned on in the locked tool box. - 1x Centrifugal Pump 1 1/2" Inch plus Suction and Delivery Hoses with Camlocks - 2x Tool Boxes - 1x Box of Hand Spanners & Sockets - Fitted Drill Rod Bins & Core Barrel Bins - Currently Registered until May 2025 Tracked Mounted Drill Rig Support Truck + Down Hole Gear Package Location: New South Wales, Australia Learn More

Make: Brevini Year: 2017 Hours: 0 (Complete Overhaul in June 2025) Weight: 1,650 kg - All Hydraulics and Electrics have been fully re-conditioned - 55kW Electric Motor driving a hydraulic pump, which in turn drives a reciprocating high pressure water pump with a maximum output of 90L/min of water at 180 Bar pressure. - The complete pump system has been designed to run continuously and all equipment is housed within a fully enclosed cover. - As the motor drives a hydraulic pump, the high pressure water output is fully adjustable while the motor runs at a constant speed, unlike a high pressure water pump that is direct driven by a fixed speed electric motor. Additionally, because the hydraulic circuit incorporates an unloader valve, it is possible to switch the high pressure water on and off without the need to stop the motor or bypass high pressure water into a holding tank. - The hydraulics system is of robust construction containing 300L of oil and an integrated oil cooler. - The system can also be used as a 55 kW hydraulic power pack. Skid Mounted Pump Location: Queensland, Australia Learn More

Make: Caterpillar Model: 3406E 550 HP Engine Number: 5EK70781 Arrangement Number: 1285403 - Removed from a 1991 Kenworth T900 Truck (Done approx. 25,000 km - Diagnosed radiator was too small in the truck for a 3x trailer road train assembly) - Number 1 Cylinder has nipped up and an insurance claim was carried out by a mechanic and an exchange of a C15 fitted to truck, engine still turns over - New Cylinder Head, Injectors, and Rocker Gear with New Top and Bottom Engine Harnesses - New Exhaust Manifold, Turbo, Water Pump, Oil Cooler & Oil Squirters - New Pistons, Liners & Rods are all IPD Parts Engine Location: Northern Territory, Australia Learn More

Rig Make: Boart Longyear Model: LS600 / BL600C Hours: 5,905 (New Engine Fitted in 2023 – Only a few hundred hours since) - 2x Boart Longyear BLY150 Reconditioned Sonic Heads (Ready to go and can be included) - Head Spares and some other big spares Support Unit Make: Morooka Hours: 423 Year: 2011 Track Mounted Multipurpose Sonic Drill Rig Support Unit Location: Scotland Learn More

Make: Nissan Model: Patrol DX GU MY08 Year: 2009 KM's: 282,381 Transmission: 5 Speed Manual Type: 4x4 - New Engine at 241,000 km's - Clutch and Flywheel - 3" Inch Exhaust - Long Range Tank - Water Tank - 2x Spare Tyres - Full Mine Spec (inc. UHF, High Vis, etc.) Ute Location: Western Australia Learn More

Make: Komatsu Model: WA 900-8 Year: 2020 Hours: 14,212 Wheel Loader Location: United States of America Learn More

Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More

Rig Model: TT300 Hours: 18 Engine: Deutz F6L912 / 66 kW Rated Depth Capacity: 300 m Feed Cylinder: 100 mm Barrel / 70 mm Shaft / 4 m Stroke Outrigger (Jacks): 4x Boxed Outriggers with 800 m Stroke Foam Pump: 21 Litre per min / 35 bar Foam/Water Tank: 120 Litre Axles: 2x 5 Tonne Air Braked Axles Tower: Direct on Cylinder / Triangle Shape Winch: 1 Tonne Push Down Force: 5,000 kgf @ 175 bar Pull Up Force: 13,000 kgf @ 175 bar Tilt Cylinders: 2x 80 Barrel 50 Shaft Breakout: 300 mm Stroke Cylinder Hydraulic Oil Tank Capacity: 330 Litres - Hydraulic Oil Cooler - Extended Tower to accommodate 4 m Stroke Cylinder - Spanners Included: 1x Breakout / 2x Keeper / 3x Hammer Modifications; - Hydraulically Tilt Rotary Head - Rotary changed to geared Rotary Head with Hollow Spindle (8,000 Nm Torque) - Including 2x Eaton Hydraulic Motors - Side Shift (on rotary head – opens up the tower for longer casing, etc.) Support Truck Make: Volvo Model: FH12 460 KM’s: 1,040,378 Type: 8x4 Air Compressor Make: Atlas Copco Model: XRV1200 Year: 2020 Hours: 122 Engine: Cummins Pressure: 22.7 bar / 330 PSI Engine/Motor Speed: 1,900 RPM Engine/Motor Power: 325 kW / 430 HP 1,200 CFM / 330 PSI - Included Drill Bits, Rods and Drilling Equipment Trailerised Drill Rig Support Truck Air Compressor Package Location: New Zealand Learn More

Rig Make: Hydrapower Model: Explorer 500 Year: 2007 Hours: 6,700 Engine: Cummins CPAK-6BTA Turbo After Cooled 6 Cylinder (176 HP @ 2,500 RPM) Rig Hydraulics; - Sauer Danfoss proportionally controlled control valves - Sauer closed loop pump on Rotary Drive Sauer open loop pump on auxiliary functions Rotary Drive; - Hydrapower Gearbox - Steel Casing with floating hollow spindle and hydraulic head lock and swing - Two Speed, 0 - 225 RPM & 0 - 966 RPM - Low speed torque to 4150 Nm - High speed torque to 966 Nm Head Travel: 6.8 m Main Winch; -Max. Pull: 4,200 kg -Max. Line Speed: 28 m/min Wireline Winch; Max. Pull: 780 kg Max. Line Speed: 83 m/min Pulldown; - Electrically controlled with dial for speed control Pull Down Capacity: 7000 kg Pull Out Capacity: 11,500 kg Mast; - Fitted with 2.0 m mast dump for angle drilling - Standard length is 10 m, supplied with hydraulically operated breakout spanner and top pulley swivel - Supplied with hydraulic circuit with quick-connect couplings for optional breakout table - Brakeout Table with Split Type Table - Bean Pump - 5x6 Gardner Denver Mud Pump (Hydraulic Driven) Truck Make: MAN Model: M2000 Year: 2005 KM's: 75,000 - Not registered - Some gearbox problems Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Includes; - 2x Complete Hammers (1x with a Hole Opener) - 1x Hammer in parts (Can Assemble with New Casing) - 17x Various Sized Shrouds (Mostly New) - 10x Bits (5x New & 5x Had One Run but Nearly New) - 7x Hammer Tubes - 4.5" Inch Remet to Metzke Hammer Adaptor and Inner Tubes - Various Other Spares S Reps 750 Gear Package Location: Western Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Make: Epiroc Model: DM-L Year: 2005 Hours: 8,453 Engine: Cummins QSX15 Tier 3 - 33.5" Inch Triple Grouser Tracks - 30' Foot Tower Carousel - Can be set up for 5.5" Inch or 6.25" Inch Rods - 4 or 5 Pieces Air End Track Mounted Rotary Drill Rig Location: United States of America Learn More

Make: Caterpillar Model: 16M Year: 2008 Hours: 37,752 (Frame) / 5,834 (After Overhaul) Engine: Caterpillar CAT C13 - Complete Overhaul in 2022 Motor Grader Location: United States of America Learn More