Search results for: 'high for size in litre fulli'

Make: Everdigm Model: Rocky B180 Bit Shank: N180 Shank Connection: API 8-5/8" Inch Reg. Pin Piston Stroke: 5.75" Inch Cylinder Bore: 12.28" Inch Hole Sizes: 18" Inch ~ 26" Inch Wrench Size: A/F 14" Inch - Brand New - Bailing Subs/Break Out Plate, etc. - Hammer forklift cradle included - 19” Hammer bit included (unused) RS Hammer Location: Queensland, Australia Learn More

Rig Make: Hanjin Model: D&B-8D Year: 2016 Hours: 5,800 Pull: 6 Metres - Warman Clamps - Under Casing Clamps - Wireline and Main Winch - Rod Bin - Auger Carrying Rack at Front of Rig - Auto SPT - Silvan Pump - Repair Kit for Silvan Pump - All New Suction and Hydraulic Hoses for Pump with Camlocks - 2x Mud Tanks (1,000 L & 500 L - Plastic) - 1x 7x5 Trailer with Fold Out Canopy + 12 Volt Fridge & Esky (In a locked container) - 2x Gas Bottles & Cookers (Mounted on Front of Trailer) - 2x 20 Litre Water Containers (Mounted on Front of Trailer) Down Hole Gear - 10x 3m PQ Rods Plus Shorts - 10x 3m HQ Rods Plus Shorts - 10x 3m NQ Rods Plus Shorts - 10x 3m Junior Mayhew Rods with Spanner Flats Plus 2x 1.5 m - 5x 100mm x 1.5m Augers Plus Bit & 20 Pins - 2x 1.5 NMLC Core Barrels - 6x NMLC Core Bits - 4x Impreg & 2x Surface Set - 40x Core Lifters / 6x Cases / 40x Stop Rings - 2x NMLC Reamers - 2x BQ Reamers - 3x BQ Core Bits - 2x 1.5m NQ3 Core Barrels - 2x Sets of Splits - 1x 3m NQ3 Core Barrel - 2x Locking Couplings - 2x Adaptor Couplings - Box of Barrel Spares - 1x HQ/NQ Overshot - 1x Set of PQ, HQ, NQ Inner Tube Wrenches - 10x 75mm Shelby Tubes Plus Drive Head - 10x 50mm Shelby Tubes Plus Drive Head - 2x SPT Samplers - 2x Pulling Plugs - 1x Spare Water Swivel Plus 2x Repair Kits - 1x Repair Kit for Rig Swivel - Many Subs to Facilitate all the Drilling Requirements - Stillsons - 2x 36" Inch, 2x 24" Inch & 2x 18" Inch - 1x Gas Mig Welder - 1x Honda 3.5 kVA Powered Generator - 1x PQ Birds Mouth for Water Return to Mud Tanks - 1x HQ Birds Mouth for Water Return to Mud Tanks - New Suction and Delivery Hoses - 1x 100mm Down Hole Hammer with 2x Bits 118mm *New* - 1x 75mm Down Hole Hammer with 2x Bits 95mm *New* - 2x 1.5m HQ3 Core Barrels - 2x 3m HQ3 Outer & Inner Splits - 1x 3m NQ3 Outer & Inner Splits - 4x HQ3 Core Bits - 20x HQ3 Core Lifters, Stop Rings & Cases Support Truck Make: Mitsubishi Model: Canter Year: 2009 Type: 4x4 - Hydraulic Hi-Ab Crane - 500 Litre Water Tank - 400 Litre Diesel Tank for Rig & 12 Volt Pump - 1x kVA Inverter - Wired so diesel pump won't engage until the switch is turned on in the locked tool box. - 1x Centrifugal Pump 1 1/2" Inch plus Suction and Delivery Hoses with Camlocks - 2x Tool Boxes - 1x Box of Hand Spanners & Sockets - Fitted Drill Rod Bins & Core Barrel Bins - Currently Registered until May 2025 Tracked Mounted Drill Rig Support Truck + Down Hole Gear Package Location: New South Wales, Australia Learn More

Capacity: 15,000 Litre Quantity: 15 Above Ground Waste Sumps / Tanks Location: New South Wales, Australia Learn More

Make: Brevini Year: 2017 Hours: 0 (Complete Overhaul in June 2025) Weight: 1,650 kg - All Hydraulics and Electrics have been fully re-conditioned - 55kW Electric Motor driving a hydraulic pump, which in turn drives a reciprocating high pressure water pump with a maximum output of 90L/min of water at 180 Bar pressure. - The complete pump system has been designed to run continuously and all equipment is housed within a fully enclosed cover. - As the motor drives a hydraulic pump, the high pressure water output is fully adjustable while the motor runs at a constant speed, unlike a high pressure water pump that is direct driven by a fixed speed electric motor. Additionally, because the hydraulic circuit incorporates an unloader valve, it is possible to switch the high pressure water on and off without the need to stop the motor or bypass high pressure water into a holding tank. - The hydraulics system is of robust construction containing 300L of oil and an integrated oil cooler. - The system can also be used as a 55 kW hydraulic power pack. Skid Mounted Pump Location: Queensland, Australia Learn More

Make: Remet Size: 4" Inch Length: 3 Metres Quantity: 54 - RC - With Inner Tubes Drill Pipe Location: Queensland, Australia Learn More

Sizes: 3" Inch / 4" Inch / 5" Inch Working Pressure: 2,500 PSI - Basic Hard Shut in Nitrile Bladder - Wireline Stripper - Hydraulic Activator - Hand Pump Activator - All Hoses Burst Protection or Fire Protected - Zone One Hoses are Coflexip and Armour Plated - Casing Adaptor to be purchased Annular Diverter Location: Queensland, Australia Learn More

- Fully Hydraulically Operated - No Electrics - Various API Screen Sizes available - 600 GPM Jack Up Rod Sloop Mounted Shale Shaker Location: Queensland, Australia Learn More

Make: Ozcon Size: 12-3/4" Inch Length: 6 Metre Quantity: 7 Casing Location: Queensland, Australia Learn More

Size: 5-9/16" Inch Length: 6 Metre Quantity: 25 Casing Location: Queensland, Australia Learn More

Make: Sterling Model: Freightliner FL80 Year: 1997 KM's: 2,384 GVM: 24,000 kg Type: 6x4 Diesel Tank: 18,000 Litres Fuel Truck Location: Queensland, Australia Learn More

Make: Nissan Model: Patrol DX GU MY08 Year: 2009 KM's: 282,381 Transmission: 5 Speed Manual Type: 4x4 - New Engine at 241,000 km's - Clutch and Flywheel - 3" Inch Exhaust - Long Range Tank - Water Tank - 2x Spare Tyres - Full Mine Spec (inc. UHF, High Vis, etc.) Ute Location: Western Australia Learn More

Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More

Make / Model: Ubuilt Cassady CTU Carrier & Booster OD Year: 2010 Hours: 310 Engine: John Deere ATM: 61,500 kg Trailer Make: Ensign Model: C.T. 1000 Year: 2005 Tyre Size: 275/70R22.5 Rim Size: 8.25x22.5 Axle Group Load Carrying Capacity: 37,500 kg - Handrail and Stair Upgrade by Obadare CTU Coil Tubing Unit Carrier Mounted Location: Queensland, Australia Learn More

Rig Model: TT300 Hours: 18 Engine: Deutz F6L912 / 66 kW Rated Depth Capacity: 300 m Feed Cylinder: 100 mm Barrel / 70 mm Shaft / 4 m Stroke Outrigger (Jacks): 4x Boxed Outriggers with 800 m Stroke Foam Pump: 21 Litre per min / 35 bar Foam/Water Tank: 120 Litre Axles: 2x 5 Tonne Air Braked Axles Tower: Direct on Cylinder / Triangle Shape Winch: 1 Tonne Push Down Force: 5,000 kgf @ 175 bar Pull Up Force: 13,000 kgf @ 175 bar Tilt Cylinders: 2x 80 Barrel 50 Shaft Breakout: 300 mm Stroke Cylinder Hydraulic Oil Tank Capacity: 330 Litres - Hydraulic Oil Cooler - Extended Tower to accommodate 4 m Stroke Cylinder - Spanners Included: 1x Breakout / 2x Keeper / 3x Hammer Modifications; - Hydraulically Tilt Rotary Head - Rotary changed to geared Rotary Head with Hollow Spindle (8,000 Nm Torque) - Including 2x Eaton Hydraulic Motors - Side Shift (on rotary head – opens up the tower for longer casing, etc.) Support Truck Make: Volvo Model: FH12 460 KM’s: 1,040,378 Type: 8x4 Air Compressor Make: Atlas Copco Model: XRV1200 Year: 2020 Hours: 122 Engine: Cummins Pressure: 22.7 bar / 330 PSI Engine/Motor Speed: 1,900 RPM Engine/Motor Power: 325 kW / 430 HP 1,200 CFM / 330 PSI - Included Drill Bits, Rods and Drilling Equipment Trailerised Drill Rig Support Truck Air Compressor Package Location: New Zealand Learn More

Make: Caterpillar Model: C11 Hours: 17,316 - With Integrated 800 Litre Diesel Tank - Dyno Test Results and ECM Available 350 HP 1,800-2,100 Complete Package with Control Panel and Starter and Alternator Dimensions; Length: Overall 250 cm (Take off 50 cm if you relocate Air Cleaner) Height to top of Valve Cover (Engine): 120 cm To top of Pre-Cleaner: 180cm To top of Muffler: 220 cm Width: 110 cm (Radiator) Skid Mounted Engine Location: Australia Learn More

Capacity: 4,000 Litres Skid Mounted Tank Location: Queensland, Australia Learn More

Make: Sandvik Model: DC302R Year: 2013 Hours: 6,030 Engine Power: 62 kW Drifter: HL300 (8 kW) - Fully Reconditioned and Painted Self Propelled Drill Rig Location: Europe Learn More

Rig Make: Hydramaster Model: 2000 - Fully Tooled & Spares - Recently painted Truck Make: International Model: Acco Year: 1998 KM's: 506,309 Type: 4x2 Engine: Cummins 300 HP Gearbox: 9 Speed Tri Axle Trailer - Near New - Set up for cable tool equipment Condition: Good Truck Mounted Cable Tool Drill Rig Tri Axle Trailer Location: Queensland, Australia Learn More

Make: Gardner Denver Model: PZ-7 - Reconditioned but not fully rebuilt Quantity: 2 Skid Mounted Bare Mud Pumps Location: Canada Learn More

Rig Make: Schramm Model: 685 Year: 1996 Hours: 2,500 (Since Rebuild) Engine: Cummins K19 Accessories; - FOPS - Rod Rack - 4x Levelling Jacks - In Mast Make/Break Rod Break Out System - Rotating Cyclone Set Up on Metz Manipulator - Airdrill Maker Breaker - Air Spanner - KL Rod Handler Set to 4.5" Inch Pipe - Dual RC Swivel and Auto Blow Down - ROPS Air-Conditioned Drillers Cabin - Complete Re-Hose 11/25 - Fire Suppression Air Compressor Make: Sullair 1,150 CFM / 500 PSI Water Capacity: Approx. 500 Litres Dimensions; Height: 4.6 m Width: 4.0 m Track Mounted Drill Rig Location: Queensland, Australia Learn More