Search results for: 'high for state alberta canada'

Make: Caterpillar Model: 773G Year: 2014 Hours: 23,585 Idle Hours: 13,606 - New Tank - 3x Adjustable Rear Spray Heads - 2x Side Spray Heads - Hose Reel - Water Cannon - Top Fill Water Truck Location: United States of America Learn More

Make: Custom Made Model: GT500 Year: 1997 Dimensions; Length: 2 Metres Width: 1.5 Metres Height: 1.2 Metres Weight: 680 kg each Bowl Capacity: 500 Litres each - Mazda Power Packs or larger most suitable for these mixers - Last Used approx. 2014 - Controlled Independently - Specifically designed to mix large volumes of High Early Strength Non-Shrink Grouts very quickly - Cycle times were designed to be less than eight minutes and continuously - Indeed full truckloads of fast setting grouts were mixed and placed using these machines in less than a shift - Mixers were commonly mounted and used from the back of our truck - There are two mixers; a left hand and a right hand - When used together the controls were in the centre between the mixers - When configured like this one operator would control both machines - One machine would be dumping while the other one was mixing - Output was continuous and in less than eight minutes per batch - Mixed grout was dumped into a hopper and taken to the site needed - Forklift Channels (Center Balanced) - Machine has mixed; Proprietary Cement Grouts, Non-Shrink Grouts, Small Aggregate Concrete, etc. - Hydraulic Driven Skid Mounted Grout Mixers & Hoppers Location: Queensland, Australia Learn More

Make: Brevini Year: 2017 Hours: 0 (Complete Overhaul in June 2025) Weight: 1,650 kg - All Hydraulics and Electrics have been fully re-conditioned - 55kW Electric Motor driving a hydraulic pump, which in turn drives a reciprocating high pressure water pump with a maximum output of 90L/min of water at 180 Bar pressure. - The complete pump system has been designed to run continuously and all equipment is housed within a fully enclosed cover. - As the motor drives a hydraulic pump, the high pressure water output is fully adjustable while the motor runs at a constant speed, unlike a high pressure water pump that is direct driven by a fixed speed electric motor. Additionally, because the hydraulic circuit incorporates an unloader valve, it is possible to switch the high pressure water on and off without the need to stop the motor or bypass high pressure water into a holding tank. - The hydraulics system is of robust construction containing 300L of oil and an integrated oil cooler. - The system can also be used as a 55 kW hydraulic power pack. Skid Mounted Pump Location: Queensland, Australia Learn More

Make: Nissan Model: Patrol DX GU MY08 Year: 2009 KM's: 282,381 Transmission: 5 Speed Manual Type: 4x4 - New Engine at 241,000 km's - Clutch and Flywheel - 3" Inch Exhaust - Long Range Tank - Water Tank - 2x Spare Tyres - Full Mine Spec (inc. UHF, High Vis, etc.) Ute Location: Western Australia Learn More

Make: Komatsu Model: WA 900-8 Year: 2020 Hours: 14,212 Wheel Loader Location: United States of America Learn More

Make: Gardner Denver Model: PZ-7 - Reconditioned but not fully rebuilt Quantity: 2 Skid Mounted Bare Mud Pumps Location: Canada Learn More

Make: Gardner Denver Model: PZ-7 Surplus Bare Mud Pump Location: Canada Learn More

Rig Make: Hydrapower Model: Explorer 500 Year: 2007 Hours: 6,700 Engine: Cummins CPAK-6BTA Turbo After Cooled 6 Cylinder (176 HP @ 2,500 RPM) Rig Hydraulics; - Sauer Danfoss proportionally controlled control valves - Sauer closed loop pump on Rotary Drive Sauer open loop pump on auxiliary functions Rotary Drive; - Hydrapower Gearbox - Steel Casing with floating hollow spindle and hydraulic head lock and swing - Two Speed, 0 - 225 RPM & 0 - 966 RPM - Low speed torque to 4150 Nm - High speed torque to 966 Nm Head Travel: 6.8 m Main Winch; -Max. Pull: 4,200 kg -Max. Line Speed: 28 m/min Wireline Winch; Max. Pull: 780 kg Max. Line Speed: 83 m/min Pulldown; - Electrically controlled with dial for speed control Pull Down Capacity: 7000 kg Pull Out Capacity: 11,500 kg Mast; - Fitted with 2.0 m mast dump for angle drilling - Standard length is 10 m, supplied with hydraulically operated breakout spanner and top pulley swivel - Supplied with hydraulic circuit with quick-connect couplings for optional breakout table - Brakeout Table with Split Type Table - Bean Pump - 5x6 Gardner Denver Mud Pump (Hydraulic Driven) Truck Make: MAN Model: M2000 Year: 2005 KM's: 75,000 - Not registered - Some gearbox problems Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Make: Epiroc Model: DM-L Year: 2005 Hours: 8,453 Engine: Cummins QSX15 Tier 3 - 33.5" Inch Triple Grouser Tracks - 30' Foot Tower Carousel - Can be set up for 5.5" Inch or 6.25" Inch Rods - 4 or 5 Pieces Air End Track Mounted Rotary Drill Rig Location: United States of America Learn More

Make: Caterpillar Model: 16M Year: 2008 Hours: 37,752 (Frame) / 5,834 (After Overhaul) Engine: Caterpillar CAT C13 - Complete Overhaul in 2022 Motor Grader Location: United States of America Learn More

Make: Atlas Copco Model: Pit Viper 275 Hours: 19,237 Load Capacity: 75,000 lb Engine: Caterpillar CAT C32 - 4 Rod Carousel approx. 40 ft. - Atlas Copco QAS 45 Diesel Generator Dimensions; Length: 41ft. 6 inch / 63ft. 6 inch (Tower Down) Width: 18ft. 4 inch Height: 67ft. / 22ft 1 inch (Tower Down) Track Mounted Drill Rig Location: Canada Learn More

Q80K - Top Head Drive - 0-8,328 Nm (6,142 ft/lbf) in low gear - High Gear 3.04:1 Ratio - Low Gear 12.61:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Gear train for High/Low Ratio Q150K - Top Head Drive - 0-14,324 Nm (10,564 ft/lbf) in low gear - High Gear 3:1 Ratio - Low Gear 22.5:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Planetary Gear set for High/Low Ratio Q280K - Top Head Drive - 0-28,000 Nm (20,651 ft/lbf) in low gear - High Gear 3:1 Ratio - Low Gear 22.5:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Dual Planetary Gear set for High/Low Ratio Rotation Head Gearboxes Location: Australia Learn More

Body Opening: 225 mm (8 3/4" Inch) OD - Fabricated High Tensile Steel Base Frame for increased strength and lighter unit weight - High Tensile Fabricated Lever Arms - Adjustable Connecting with Left & Right Hand Threads allowing accurate adjustment of jaw actuation - Cast Jaw Assemblies to suit most standard drill rod sizes - Light weight casting approx. 16 kg per jaw - Easily replaceable Gripper Inserts for NQ & HQ Jaw Sizes - RC Slips Table, Holders and Inserts to suit 3 1/2", 4" & 4 1/2" Rod Sizes - Changeable with Industry Standard Rod Clamps Rod Clamp Location: Australia Learn More

Model: FH2000 Engine: Caterpillar CAT C7.1 Electronic @ 205 kW (275 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Up: 50 m/min (164 ft/min) Down: 39 m/min (128 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - Bosch Rexroth A6VM160 Variable Displacement Motor - High Gear 3:1 & Low Gear 19.57:1 ratios - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube Bearings and Gears with filtered and cooled lubrication oil system Main Winch; - Maximum Pull: 156 kN (35,048 lbf) - 120 m/min (394 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - 28 mm Main Winch Rope - Safety Factor 3.35:1 (exceeds BS/EN791) - 1x Bosch Rexroth A6VM160 Variable Displacement Motors - 1x Brevini Planetary Reduction Gear Boxes - 1x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release Wireline Winch; - Mast Mounted - Maximum Pull: 25 kN (5,617 lbf) - Rope Capacity: 2,100 Metres x 8 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1300 Engine: Caterpillar CAT C7.1 Electronic @ 187 kW (250 HP) Pull Back: 115 kN (25,853 lbf) Actual Pull Down: 70 kN (15,736 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 1,300 m HQ Core: 885 m Open Hole 3 1/2" Inch Rods: 380 m RC 4 1/2" Inch: 220 m (Nominal) Traverse Speed; Up: 60 m/min (196.8 ft/min) Down: 56 m/min (183.7 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 8,087 Nm (6,111 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - High Gear 3.04:1 & Low Gear 12.61:1 ratios - Variable Displacement 160cc Hydraulic Motor - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube System with Cooler and Filter Main Winch; - Maximum Pull: 100 kN (10,000 lbf) - 120 m/min (393 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - Main Winch Rope - Safety Factor to Meet BS/EN791 - Planetary Reduction Gear Box & Brake - Variable Displacement Hydraulic Motor Drive Wireline Winch; - Deck Mounted - Maximum Pull: 15 kN (3,372 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: 1750 Scout Engine: Perkins Diesel Torque: 2,500 Nm at 205 bar and 110 RPM Stroke: 1.75 m Pull-Out / Pull-Down: 1,100 kg Capacity (Guide Only): NQ - 60 m / 4" Inch Open Hole - 30 m / 3 1/2" Inch Auger - 15 m - Custom Toyota 33220 Tray - Direct Dive Auger Head with High Torque Head Motor and Fittings - Fine Feed Control - Auger Drive Sub (1 1/8" Inch Hex) - RHS Mast - Tilt Frame for Vehicle/Trailer Mounting - Hydraulic Tilt - Heavy Duty Pull-Down Chain - Nylon Idler Rollers - Standard Auger Guide - Standard Control Panel - Hydraulic Operation - Rain Hood for Motor & Lockable Cage for Spare Wheel & Motor - Remove Throttle and Stop - Water Filter for Fuel / Water Separation - Light Guard for Augers 500 mm to 1,800 mm - Oil Cooler - Simple Rack for Augers Options for Drill; - Hollow Spindle Head and Tooling for Fluid Drilling - 2 Levelling Jacks for Tray Mount Drills - Tilting Rack for Augers - Alternative Engine Options to suit existing fleet Toyota Landcruiser Upgrade Kit; - Roof Racks for Spare Tyre (31678) - Roof Rack Mounts Pair (31679) - GVM Upgrade Spring Kit @ 4,200 kg (Supply Only - 31680) - Bellows Suspension Kit (Supply Only - 31730) - Storage Box LH Under Deck (33249) - Storage Box RH Under Deck (33248) - Under Deck Water Tanks @ 29 Litres (33137) *Ready for mounting to a Toyota 79 Series Landcruiser Cab Chassis* Drill Rig Location: Australia Learn More

Make: Ariel Model: JGP2 Part Number: CL190390 Weight: 388.1 kg Brand New High Pressure Cooler Panels Location: Victoria, Australia Learn More

Make / Model: TL-400 Contains: - Tower - Flashlight - Headlight - Charger - Driver - Battery System D24-100 - USD Output, 5V 2A (2 Dock) for charging Headlight, Flashlight or Mobile Phone - 1-3 Battery Pack (1 Battery 30+ Hours extreme mode) - Height: 64.5 cm - 220 cm - Weight: 12.85 kg - One Man Operation - Self locking and 30 degree + up/down adjustable pole - Run Times > 10 hours (High output, 3 batteries) Application - Drilling - Construction - Maintenance - Events - Mining - Emergency - Infrastructure - Personal Control Board - Power Switch - Brightness - DIM+, DIM- - Battery Level - AC Plug - USB Output Light Brightness Area: 1,100 m2 5 m - 490 lux / 10 m - 120 lux / 20 m - 29 lux / 40 m - 7 lux Battery / AC 100-227V - AC 0-15,000 LM - High 8,000 LM - Medium 5,000 LM - Low 2,500 LM - Extreme 800 LM - Rate Power 28 wh - Rate Voltage 24.5 V - Rate Capacity 40 Ah - Working Temp: -10 to 50 degrees - Working Humidity: -20 to 95% Portable Light Tower Location: Queensland, Australia Learn More