Search results for: 'hire for size in dual rpm brand'
- Related search terms
- hire for sale in de ram beach
- hire for sale in deridder la
- hire for sale alpena corner
- hire for sale alpena cooler
- hire for sale in dm ram bean
-
2022 Boart Longyear LF160C Track Mounted Drill Rig (POA) (sale-ehub4162)For Sale$0.00Drill Rig Make: Boart Longyear Model: LF160C Year: 2022 Installed Power: 194 kW Working Pressure: 380 bar Head Torque: 665 I / 90 II daNm Head Rotation: 250 I / 1,050 II RPM Feed Force: 7,000 daN Retract Force: 17,000 daN Feed Length: 7,200 mm Tracks Make: Strickland Model: 6000428 Year: 2022 Track Mounted Drill Rig Location: Queensland, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND Boart Longyear
LOCATION Queensland, Australia
MODEL LF160C
-
New Holland B115B Backhoe (FOR HIRE/RENT - POA) (hire-ehub4154)For HireMake: New Holland Model: B115B Backhoe Location: New South Wales, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND New Holland
LOCATION New South Wales, Australia
MODEL B115B
-
2020 Drill Techniques GM-2GI Hydraulic Jack Up Grout Unit (FOR HIRE/RENT - POA) (hire-ehub4149)For HireMake: Drill Techniques Model: GM-2GI Year: 2020 Height: 3.5 Metres Tare: 4,000 kg Hydraulic Jack Up Grout Unit Location: New South Wales, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND Drilling Techniques
LOCATION New South Wales, Australia
MODEL GM-2GI
-
15x 15,000 Litre Above Ground Waste Sumps / Tanks (FOR HIRE/RENT - POA) (hire-ehub4147)For HireCapacity: 15,000 Litre Quantity: 15 Above Ground Waste Sumps / Tanks Location: New South Wales, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND N/A
LOCATION New South Wales, Australia
MODEL 15,000 Litre
-
54x 3 Metre Lengths of 4" Inch Remet RC Drill Pipe with Inner Tubes ($650 ex GST per length) (sale-ehub4081)For Sale$650.00Make: Remet Size: 4" Inch Length: 3 Metres Quantity: 54 - RC - With Inner Tubes Drill Pipe Location: Queensland, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND Remet
LOCATION Queensland, Australia
MODEL 3 Metre
-
Foot Clamp + BQ, NQ, HQ, PQ, PWT Jaw Sets + Jaw Teeth Inserts (POA) (sale-ehub4130)For Sale$0.00- Complete Foot Clamp (ex Jaws) - BQ Jaw Set c/w Teeth - NQ Jaw Set c/w Teeth - HQ Jaw Set c/w Teeth - PQ Jaw Set c/w Teeth - PWT Jaw Set c/w Teeth - In Cast PQ Jaw Set - Jaw Teeth Insert Set *Brand New Location: New South Wales, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND N/A
LOCATION New South Wales, Australia
MODEL See Description
-
Annular Diverter (FOR HIRE/RENT - POA) (hire-ehub4126)For Sale$0.00Sizes: 3" Inch / 4" Inch / 5" Inch Working Pressure: 2,500 PSI - Basic Hard Shut in Nitrile Bladder - Wireline Stripper - Hydraulic Activator - Hand Pump Activator - All Hoses Burst Protection or Fire Protected - Zone One Hoses are Coflexip and Armour Plated - Casing Adaptor to be purchased Annular Diverter Location: Queensland, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND N/A
LOCATION Queensland, Australia
MODEL 3" / 4" / 5" Inch
-
600 GPM Shale Shaker Mounted on Jack Up Rod Sloop (FOR HIRE/RENT - POA) (hire-ehub4125)For Hire- Fully Hydraulically Operated - No Electrics - Various API Screen Sizes available - 600 GPM Jack Up Rod Sloop Mounted Shale Shaker Location: Queensland, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND N/A
LOCATION Queensland, Australia
MODEL 600 GPM
-
HT400 Skid Mounted Triplex Mud Pump (FOR HIRE/RENT - POA) (hire-ehub4124)For HireModel: HT400 Engine: Cummins Transmission: Alison Gearbox - Variable Speed - 450 to 500 GPM Skid Mounted Triplex Mud Pump Location: Queensland, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND N/A
LOCATION Queensland, Australia
MODEL HT400
-
7x 6 Metre Lengths of Ozcon 12-3/4" Inch Casing (POA) (sale-ehub4084)For Sale$0.00Make: Ozcon Size: 12-3/4" Inch Length: 6 Metre Quantity: 7 Casing Location: Queensland, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND N/A
LOCATION Queensland, Australia
MODEL 12-3/4" Inch
-
25x 6 Metre Lengths of 5-9/16" Inch Casing (POA) (sale-ehub4082)For Sale$0.00Size: 5-9/16" Inch Length: 6 Metre Quantity: 25 Casing Location: Queensland, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND N/A
LOCATION Queensland, Australia
MODEL 5-9/16" Inch
-
45x 6 Metre Lengths of HWT Surepipe Casing (POA) (sale-ehub4079)For Sale$0.00Make: HWT Length: 6 Metre Quantity: 45 - Surepipe - Brand New Casing Location: Queensland, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND N/A
LOCATION Queensland, Australia
MODEL HWT Surepipe
-
2016 Ford Ranger Dual Cab Ute (POA) (sale-ehub4057)For Sale$0.00Make: Ford Model: Ranger Year: 2016 KM's: 198,349 GVM: 3,200 kg Dual Cab Ute Location: Queensland, Australia Learn MoreMachine hours N/A KILOMETERS 198,349
YEAR 2016
BRAND Ford
LOCATION Queensland, Australia
MODEL Ranger
-
Brand New Gertec Skid Mounted Grout Unit ($107,500 ex GST) (sale-ehub4045)For Sale$107,500.00Make: Gertec - Brand New - Never Used Skid Mounted Grout Unit Location: Victoria, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND N/A
LOCATION Victoria, Australia
MODEL N/A
-
Doosan Air End Suitable for PA536, XHP1250 & XHP1170 Air Compressors ($48,000 ex GST) (sale-ehub4024)For Sale$48,000.00Make: Doosan Models (Suitable): PA536, XHP1250 & XHP1170 - Brand New - Tailored to meet specific requirements - Inclusive of Warranty Air End Location: Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND Doosan
LOCATION Australia
MODEL PA536, XHP1250 & XHP1170
-
2006 Caterpillar CAT C15 Skid Mounted Engine ($59,000 ex GST) (sale-ehub4016)For Sale$59,000.00Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn MoreMachine hours 1,400
KILOMETERS N/A YEAR 2006
BRAND Caterpillar CAT
LOCATION Queensland, Australia
MODEL C15
-
2010 Ubuilt Cassady CTU Coil Tubing Unit Mounted on 2005 Ensign Carrier ($295,000 ex GST) (sale-ehub4015)For Sale$295,000.00Make / Model: Ubuilt Cassady CTU Carrier & Booster OD Year: 2010 Hours: 310 Engine: John Deere ATM: 61,500 kg Trailer Make: Ensign Model: C.T. 1000 Year: 2005 Tyre Size: 275/70R22.5 Rim Size: 8.25x22.5 Axle Group Load Carrying Capacity: 37,500 kg - Handrail and Stair Upgrade by Obadare CTU Coil Tubing Unit Carrier Mounted Location: Queensland, Australia Learn MoreMachine hours N/A KILOMETERS N/A YEAR 2010
BRAND N/A
LOCATION Queensland, Australia
MODEL Ubuilt Cassady CTU Carrier & Booster OD
-
2007 Drill Rig Mounted on 2007 Isuzu FTS 750 4x4 Table Top Truck ($145,000 ex GST) (sale-ehub4003)For Sale$145,000.00Rig Year: 2007 Hours: 3,000 Engine: Caterpillar (85 HP) Stroke: 3,300 mm - 2 Speed Head Rotation Torque: 2,500/450 Nm Rotation Speed: 140/750 RPM Pullback: 7,000 kg Pull Down: 4,000 kg - Set up for Geotechnical Drilling with Auto SPT - 1x Main Winch - 2x Wireline Winch - Mono Pump - Four Jack Legs - Drilling Rods, Alloy Mud Tanks, Accessories for 50 m (All in Good Condition) Truck Make: Isuzu Model: FTS 750 Year: 2007 KM's: 55,000 Type: 4x4 Table Top Truck Mounted Drill Rig Location: Queensland, Australia Learn MoreMachine hours 3,000
KILOMETERS 55,000
YEAR 2007
BRAND N/A
LOCATION Queensland, Australia
MODEL N/A
-
TT300 Trailerised Drill Rig + Volvo FH12 460 Truck with Atlas Copco XRV1200 Air Compressor & More Package (POA) (sale-ehub3999)For Sale$0.00Rig Model: TT300 Hours: 18 Engine: Deutz F6L912 / 66 kW Rated Depth Capacity: 300 m Feed Cylinder: 100 mm Barrel / 70 mm Shaft / 4 m Stroke Outrigger (Jacks): 4x Boxed Outriggers with 800 m Stroke Foam Pump: 21 Litre per min / 35 bar Foam/Water Tank: 120 Litre Axles: 2x 5 Tonne Air Braked Axles Tower: Direct on Cylinder / Triangle Shape Winch: 1 Tonne Push Down Force: 5,000 kgf @ 175 bar Pull Up Force: 13,000 kgf @ 175 bar Tilt Cylinders: 2x 80 Barrel 50 Shaft Breakout: 300 mm Stroke Cylinder Hydraulic Oil Tank Capacity: 330 Litres - Hydraulic Oil Cooler - Extended Tower to accommodate 4 m Stroke Cylinder - Spanners Included: 1x Breakout / 2x Keeper / 3x Hammer Modifications; - Hydraulically Tilt Rotary Head - Rotary changed to geared Rotary Head with Hollow Spindle (8,000 Nm Torque) - Including 2x Eaton Hydraulic Motors - Side Shift (on rotary head – opens up the tower for longer casing, etc.) Support Truck Make: Volvo Model: FH12 460 KM’s: 1,040,378 Type: 8x4 Air Compressor Make: Atlas Copco Model: XRV1200 Year: 2020 Hours: 122 Engine: Cummins Pressure: 22.7 bar / 330 PSI Engine/Motor Speed: 1,900 RPM Engine/Motor Power: 325 kW / 430 HP 1,200 CFM / 330 PSI - Included Drill Bits, Rods and Drilling Equipment Trailerised Drill Rig Support Truck Air Compressor Package Location: New Zealand Learn MoreMachine hours 18
KILOMETERS 1,040,378
YEAR 2020
BRAND N/A
LOCATION New Zealand
MODEL TT300
-
Schramm T660 H Rotadrill Track Mounted Drill Rig (POA) (sale-ehub3996)For Sale$0.00Make: Schramm Model: T660 H Rotadrill Engine: Caterpillar CAT 3406B DITA @ 450 HP Pulldown: 30,000 lbs Pullback: 44,000 lbs Capacity: 5" Inch Rams / 350 m R/C 4 1/2" Inch Remet Rods Stroke: 6.5 m Top Drive: R/C Head Twin Motor 2 Speed / 0-160 RPM @ 38,000 lbs / 0-53 RPM @ 75,000 lbs Onboard Air Compressor: Sullair 900 CFM / 350 PSI Mounting: Caterpillar CAT 325 Wide Track Track Mounted Drill Rig Location: New Zealand Learn MoreMachine hours N/A KILOMETERS N/A YEAR N/A BRAND Schramm
LOCATION New Zealand
MODEL T660 H
Filter