Search results for: 'hole for state 11234'

- Has Jack Up Leg Holes (No Legs) Length: 6 Metre Rod Sloop Location: Queensland, Australia Learn More

Make: Komatsu Model: WA 900-8 Year: 2020 Hours: 14,212 Wheel Loader Location: United States of America Learn More

Includes; - 2x Complete Hammers (1x with a Hole Opener) - 1x Hammer in parts (Can Assemble with New Casing) - 17x Various Sized Shrouds (Mostly New) - 10x Bits (5x New & 5x Had One Run but Nearly New) - 7x Hammer Tubes - 4.5" Inch Remet to Metzke Hammer Adaptor and Inner Tubes - Various Other Spares S Reps 750 Gear Package Location: Western Australia Learn More

Make: Epiroc Model: D65 - Unit off a Eprioc D65 Blast Hole Drill Rig Cyclone Location: Western Australia Learn More

Make: Epiroc Model: DM-L Year: 2005 Hours: 8,453 Engine: Cummins QSX15 Tier 3 - 33.5" Inch Triple Grouser Tracks - 30' Foot Tower Carousel - Can be set up for 5.5" Inch or 6.25" Inch Rods - 4 or 5 Pieces Air End Track Mounted Rotary Drill Rig Location: United States of America Learn More

Make: Caterpillar Model: 16M Year: 2008 Hours: 37,752 (Frame) / 5,834 (After Overhaul) Engine: Caterpillar CAT C13 - Complete Overhaul in 2022 Motor Grader Location: United States of America Learn More

Rig Make: Edson Model: Versadrill 300 Year: 1996 Engine: Hatze - 6x6 Multidrive Technology - Rotation head MR260 Rotation hollow spindle, single speed, dial in, rotation head around 120 rpm - Winching gear on back of mast for hollow augering - Can do diamond drilling if you were to change the hydraulic motor - Dump Mast - Near New Hydraulic Pump - 4x Leveling Jacks - Currently doing 80mtr holes at 4.5” - Client used to aircore with it, but currently set up doing mud - Used to do a lot of Geotech work, 6” hollow augering - Southern Cross Mud pump on the side - 3.2 mtr Stroke - 3 mtr Rods - Extension arm to run 6mtr casing into the ground Ute Make: Toyota Model: Landcruiser Year: 1990 KM's: 107,000 Ute Mounted Drill Rig Location: Western Australia Learn More

Drill Rig Make: Chicago Pneumatic Model: CP650 Year: 1981 Engine: Caterpillar CAT 3406 Onboard Air Compressor: GHH 825 CFM / 350 PSI Twin Screw Injection Pump: Comet APS 71 ltr/min @ 580 PSI Casing Driver: 612 Banger 6" Inch - 12" Inch Winch: 1/2" Inch 7,000 lbs Extendable Rod Handling Jib Hole Capacity: 6" Inch - 12" Inch 500 m 4 1/2" Inch Rods Capacity; Pull Down: 21,000 lbs Pull Back: 55,000 lbs 5 1/2" Inch Heavy Hoist Rams 73 ft/min Rapid Feed - 160 Pitch Chains Levelling Jacks; Front: 1 x 5" Inch x 48" Inch Stroke Rear: 2 x 5" Inch x 36" Inch Stroke Top Drive Rotary; 0-152 RPM - 76,000 lb Torque Twin Dynex Motors R/C Head - 7 m Travel Carrier Type: 6x4 Engine: Caterpillar CAT 3208 @ 210 HP Crane Carrier Carrier Mounted Water Well Drill Rig Location: New Zealand Learn More

Model: FH3000 Engine: Cummins QSL Electronic @ 255 kW (342 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Maximum Speed: 55.5 m/min (182 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - 100% Theoretical Main Winch; - Maximum Pull: 226 kN (50,806 lbf) - Maximum Speed: 100 m/min (328 ft/min) - 2x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release - 9 Metre Rod Pull Capacity Wireline Winch; - Maximum Pull: 27 kN (6,069 lbf) - Rope Capacity: 3,000 Metres x 8 mm Rope - Maximum Speed: 450 m/min (1,476 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH2000 Engine: Caterpillar CAT C7.1 Electronic @ 205 kW (275 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Up: 50 m/min (164 ft/min) Down: 39 m/min (128 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - Bosch Rexroth A6VM160 Variable Displacement Motor - High Gear 3:1 & Low Gear 19.57:1 ratios - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube Bearings and Gears with filtered and cooled lubrication oil system Main Winch; - Maximum Pull: 156 kN (35,048 lbf) - 120 m/min (394 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - 28 mm Main Winch Rope - Safety Factor 3.35:1 (exceeds BS/EN791) - 1x Bosch Rexroth A6VM160 Variable Displacement Motors - 1x Brevini Planetary Reduction Gear Boxes - 1x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release Wireline Winch; - Mast Mounted - Maximum Pull: 25 kN (5,617 lbf) - Rope Capacity: 2,100 Metres x 8 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1300 Engine: Caterpillar CAT C7.1 Electronic @ 187 kW (250 HP) Pull Back: 115 kN (25,853 lbf) Actual Pull Down: 70 kN (15,736 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 1,300 m HQ Core: 885 m Open Hole 3 1/2" Inch Rods: 380 m RC 4 1/2" Inch: 220 m (Nominal) Traverse Speed; Up: 60 m/min (196.8 ft/min) Down: 56 m/min (183.7 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 8,087 Nm (6,111 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - High Gear 3.04:1 & Low Gear 12.61:1 ratios - Variable Displacement 160cc Hydraulic Motor - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube System with Cooler and Filter Main Winch; - Maximum Pull: 100 kN (10,000 lbf) - 120 m/min (393 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - Main Winch Rope - Safety Factor to Meet BS/EN791 - Planetary Reduction Gear Box & Brake - Variable Displacement Hydraulic Motor Drive Wireline Winch; - Deck Mounted - Maximum Pull: 15 kN (3,372 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: 1750 Scout Engine: Perkins Diesel Torque: 2,500 Nm at 205 bar and 110 RPM Stroke: 1.75 m Pull-Out / Pull-Down: 1,100 kg Capacity (Guide Only): NQ - 60 m / 4" Inch Open Hole - 30 m / 3 1/2" Inch Auger - 15 m - Custom Toyota 33220 Tray - Direct Dive Auger Head with High Torque Head Motor and Fittings - Fine Feed Control - Auger Drive Sub (1 1/8" Inch Hex) - RHS Mast - Tilt Frame for Vehicle/Trailer Mounting - Hydraulic Tilt - Heavy Duty Pull-Down Chain - Nylon Idler Rollers - Standard Auger Guide - Standard Control Panel - Hydraulic Operation - Rain Hood for Motor & Lockable Cage for Spare Wheel & Motor - Remove Throttle and Stop - Water Filter for Fuel / Water Separation - Light Guard for Augers 500 mm to 1,800 mm - Oil Cooler - Simple Rack for Augers Options for Drill; - Hollow Spindle Head and Tooling for Fluid Drilling - 2 Levelling Jacks for Tray Mount Drills - Tilting Rack for Augers - Alternative Engine Options to suit existing fleet Toyota Landcruiser Upgrade Kit; - Roof Racks for Spare Tyre (31678) - Roof Rack Mounts Pair (31679) - GVM Upgrade Spring Kit @ 4,200 kg (Supply Only - 31680) - Bellows Suspension Kit (Supply Only - 31730) - Storage Box LH Under Deck (33249) - Storage Box RH Under Deck (33248) - Under Deck Water Tanks @ 29 Litres (33137) *Ready for mounting to a Toyota 79 Series Landcruiser Cab Chassis* Drill Rig Location: Australia Learn More

Make: Hydco Model: 1000H Year: 2008 Hours: 4,304 Engine: Cummins 6CTA Onboard Air Compressor: Sullair 1,150 CFM / 350 PSI & 900 CFM / 500 PSI Compressor Hours: 819 Compressor Engine: Caterpillar CAT C15 - Setup for mainly RC however has the diamond capabilities & equipment - Rig has recently been completing RC holes to depths of 425 m coupled with the Aux Compressor Kit giving 2,400 CFM / 1,000 PSI Diamond Drilling Capacity; HQ: 1,000 m NQ: 1,500 m PQ: 600 m Features; - Harlsan Auto Blow Up and Blowdown - KL Rod Handler - Hydraulic Breakouts - Hydraulic Spanners - Safety Cage with Interlock - Quick Access Mountable Stuffing Box Assembly - Fire Suppression - Dust Suppression - FMC Bean Pump for Diamond Drilling - FMC Dual Pump for Water Injection - Hydraulic Foot Clamps - Diamond Drilling Safety Cage - Diamond Drilling Platform - Storage Area with Safety Rails and Access Ladders - Refurbished Cyclone - New Cone Splitter - New Track Chains and Rollers - 400x Metres of 4.5" Inch Remet Rods - Airdrill 670 Hammers & Bits - Other specific RC Gear Track Mounted Drill Rig Location: Western Australia Learn More

Make: Gardner Denver Model: PZ-7 Year: 2014 - Triplex w/ Forged Steel Fluid End & Quick Change Caps - 5M Pulsation Dampener - Oteco 3" Inch Shear Relief Valve - Pressure Gauge - Mission 6x5 Charge Pump - Fitted with 7" Inch Liners & Pistons - No Engine or Transmission Condition: Good Skid Mounted Mud Pump Location: United States of America Learn More

Make: Globe Drill Model: KAL 500-CP8 Year: 2009 Hours: 27,332 (Lifetime) / Current Hours: 3,406 Engine: Detroit Series 2000 @ 905 HP Engine Hours: 11,982 Onboard Air Capacity: 1,350 CFM / 500 PSI Hole Inclination: 90-50 degrees Rod String: No Rods - Set up for 4 1/2" Inch Rods Depth Capacity On Board: 330 m Overall Width: 3.9 m Compressor Make: Sullair 1,350 CFM 500 PSI Hours: 2,308 Features; - Polyurethane Cyclone - Cone Sample Splitter - Dual Breakout System - Dust Suppression - Carousel - Rod Cage - Overhead Protection - Fire Suppression - Remote Tramming Track Mounted Drill Rig Location: Western Australia Learn More

Make: SD Model: 100 Year: 2003 Hours: 22,738 (Overall approx.) Engine Hours: 10,793 (New Hour Metre with Current Hours since engine change - 1,977) Onboard Air Capacity: 1,150 CFM / 500 PSI Air Compressor Hours: 12,768 Rotary Head Hours: 2,054 (Since Change Out) Hole Inclination Range: 90-50 degrees Rod String: 4 Met / 6 m Depth Capacity: 60 m Overall Width: 2.95 m - Spare Engine requires rebuild and spares to go with the drill Features - Polyurethane Cyclone - Cone Sample Splitter - Dual Breakout System - Dust Suppression - Carousel - Rod Cage - Overhead Protection - Fire Suppression Track Mounted Drill Rig Location: Western Australia Learn More

Make: Sandvik Model: DR560/80 Hours: Various Max Feed Rate: 1.3 m/s (257 ft/min) Max Hoisting @ 2,100 RPM: 47 kN (10,600 lbf) Max Pulldown @ 2,100 RPM: 47 kN Top Drive Rotation Torque: 5,730 Nm Rotation Speed: 0-80 RPM (Variable) Carousel Standard Capacity: 6 Rods (5 Rods for OD 140 mm (5.5" inch) Max Rod Size: 140 mm / 5.5" inch Min Rod Size: 89 mm / 3.5" inch Rod Length: 6.1 m / 20 ft Min Hammer Size: 102 mm / 4" inch Carousel Hole Depth: 42.6 m / 140 ft Max Hole Size: 216 mm / 8.5" inch Min Hole Size: 115 mm / 4.5" inch + More information can be provided Track Mounted Contour DTH Drill Rig Location: Western Australia Learn More

Type: 2-7/8" Inch IF / 4" Inch OD Length: 6 m - Were purchased out of USA original and were 20' (6.2 metres), then remanufactured with a “baker joint” to make them 6 metre lengths - Not required anymore due to offset joint interferes with UDR style rod spinner Condition: Excellent - 70-80 Metres are new and have never been down a hole (rest have only been down one hole) Quantity: Approx. 30 Metres Drill Rod / Pipe Location: New South Wales, Australia Learn More

Drill Rig Make: NW Model: 500 - Heli / Man Portable 126 HP Included; - Hydraulic Control Panel - Hydraulic Reservoir c/w Oil to Water Heat Exchanger - 3x Kubota Turbo Charged Diesel Engines @ 42 HP - Light Weight 39 GPM Down Hole Pump - 220 Litre Fuel Tank and AL Stand Feed Frame Complete - Wireline Winch with 750 m 3/16" Inch Wireline Installed - Top Drive Drill Head with Adapter Sub for HWL Drill Rod - Two Rotation Motors for NWL & HWL Drill Rod - 4.5" Inch Rod Clamp c/w Jaws and Steadier Bearing for H & N Rods - Hydraulic Mud Mixer with Safety Shielding - Light Weight AL Mast Rotation Guard - Spline Wrench for Locking Head to change out Drilling Subs Heli Portable Drill Rig Package Location: Canada Learn More

Make: American Open Hole Model: 2 7/8" Inch 6 Metre Mid Body OD: 73 mm Tool Joint OD: 95 mm Quantity: 70 Lengths Drill Rod / Pipe Location: Queensland, Australia Learn More