Search results for: 'hose for state in little fulli'

Make: Caterpillar Model: 825G Year: 2003 Hours: 10,356 Soil Compactor Location: United States of America Learn More

Make: Caterpillar Model: 773G Year: 2014 Hours: 23,585 Idle Hours: 13,606 - New Tank - 3x Adjustable Rear Spray Heads - 2x Side Spray Heads - Hose Reel - Water Cannon - Top Fill Water Truck Location: United States of America Learn More

Rig Make: Hanjin Model: D&B-8D Year: 2016 Hours: 5,800 Pull: 6 Metres - Warman Clamps - Under Casing Clamps - Wireline and Main Winch - Rod Bin - Auger Carrying Rack at Front of Rig - Auto SPT - Silvan Pump - Repair Kit for Silvan Pump - All New Suction and Hydraulic Hoses for Pump with Camlocks - 2x Mud Tanks (1,000 L & 500 L - Plastic) - 1x 7x5 Trailer with Fold Out Canopy + 12 Volt Fridge & Esky (In a locked container) - 2x Gas Bottles & Cookers (Mounted on Front of Trailer) - 2x 20 Litre Water Containers (Mounted on Front of Trailer) Down Hole Gear - 10x 3m PQ Rods Plus Shorts - 10x 3m HQ Rods Plus Shorts - 10x 3m NQ Rods Plus Shorts - 10x 3m Junior Mayhew Rods with Spanner Flats Plus 2x 1.5 m - 5x 100mm x 1.5m Augers Plus Bit & 20 Pins - 2x 1.5 NMLC Core Barrels - 6x NMLC Core Bits - 4x Impreg & 2x Surface Set - 40x Core Lifters / 6x Cases / 40x Stop Rings - 2x NMLC Reamers - 2x BQ Reamers - 3x BQ Core Bits - 2x 1.5m NQ3 Core Barrels - 2x Sets of Splits - 1x 3m NQ3 Core Barrel - 2x Locking Couplings - 2x Adaptor Couplings - Box of Barrel Spares - 1x HQ/NQ Overshot - 1x Set of PQ, HQ, NQ Inner Tube Wrenches - 10x 75mm Shelby Tubes Plus Drive Head - 10x 50mm Shelby Tubes Plus Drive Head - 2x SPT Samplers - 2x Pulling Plugs - 1x Spare Water Swivel Plus 2x Repair Kits - 1x Repair Kit for Rig Swivel - Many Subs to Facilitate all the Drilling Requirements - Stillsons - 2x 36" Inch, 2x 24" Inch & 2x 18" Inch - 1x Gas Mig Welder - 1x Honda 3.5 kVA Powered Generator - 1x PQ Birds Mouth for Water Return to Mud Tanks - 1x HQ Birds Mouth for Water Return to Mud Tanks - New Suction and Delivery Hoses - 1x 100mm Down Hole Hammer with 2x Bits 118mm *New* - 1x 75mm Down Hole Hammer with 2x Bits 95mm *New* - 2x 1.5m HQ3 Core Barrels - 2x 3m HQ3 Outer & Inner Splits - 1x 3m NQ3 Outer & Inner Splits - 4x HQ3 Core Bits - 20x HQ3 Core Lifters, Stop Rings & Cases Support Truck Make: Mitsubishi Model: Canter Year: 2009 Type: 4x4 - Hydraulic Hi-Ab Crane - 500 Litre Water Tank - 400 Litre Diesel Tank for Rig & 12 Volt Pump - 1x kVA Inverter - Wired so diesel pump won't engage until the switch is turned on in the locked tool box. - 1x Centrifugal Pump 1 1/2" Inch plus Suction and Delivery Hoses with Camlocks - 2x Tool Boxes - 1x Box of Hand Spanners & Sockets - Fitted Drill Rod Bins & Core Barrel Bins - Currently Registered until May 2025 Tracked Mounted Drill Rig Support Truck + Down Hole Gear Package Location: New South Wales, Australia Learn More

Make: Brevini Year: 2017 Hours: 0 (Complete Overhaul in June 2025) Weight: 1,650 kg - All Hydraulics and Electrics have been fully re-conditioned - 55kW Electric Motor driving a hydraulic pump, which in turn drives a reciprocating high pressure water pump with a maximum output of 90L/min of water at 180 Bar pressure. - The complete pump system has been designed to run continuously and all equipment is housed within a fully enclosed cover. - As the motor drives a hydraulic pump, the high pressure water output is fully adjustable while the motor runs at a constant speed, unlike a high pressure water pump that is direct driven by a fixed speed electric motor. Additionally, because the hydraulic circuit incorporates an unloader valve, it is possible to switch the high pressure water on and off without the need to stop the motor or bypass high pressure water into a holding tank. - The hydraulics system is of robust construction containing 300L of oil and an integrated oil cooler. - The system can also be used as a 55 kW hydraulic power pack. Skid Mounted Pump Location: Queensland, Australia Learn More

Sizes: 3" Inch / 4" Inch / 5" Inch Working Pressure: 2,500 PSI - Basic Hard Shut in Nitrile Bladder - Wireline Stripper - Hydraulic Activator - Hand Pump Activator - All Hoses Burst Protection or Fire Protected - Zone One Hoses are Coflexip and Armour Plated - Casing Adaptor to be purchased Annular Diverter Location: Queensland, Australia Learn More

- Fully Hydraulically Operated - No Electrics - Various API Screen Sizes available - 600 GPM Jack Up Rod Sloop Mounted Shale Shaker Location: Queensland, Australia Learn More

Make: G&K Model: 850 Engine: Caterpillar CAT 3208 (Rebuilt) Hours: 200 approx. - Replaced Extensive Hydraulic Hoses - Bean Pump on deck - 72 Metres of 4" Inch Waterbore Drill Pipe, comes with Head Tubes and Air Swivel Lots of Spares; - 2x Spare Heads -2x Spare Winches -1x Spare Wireline Drilling Capacity; 12" Inch Hole: Approx. 200 + Metres NQ: 800 Metres HQ: 600 Metres Truck Mounted Waterbore / Diamond Drill Rig Location: Victoria, Australia Learn More

Rig Make: UDR Model: 650 Onboard Compressor: Sullair 1,150 CFM / 350 PSI Air Compressor - Set up for Waterbores, RC and Aircore - Table opens up to allow 14” inch casing or bit - Recent major service of Air End, Separator Filter & New Oil - New Head Slides - New Jib Ram - New Pull Down Ropes - Head Serviced Includes; - Cyclone & Splitter - New Bull Hose - 25x Used 4” Inch RC Rods with Inner Tubes - 2x Head Tubes - Air RC Swivel - Mud Rotary Swivel - Hydraulic Breakout Arm - 4” Inch Airdrill RC Hammer (in Good Condition) & 2x Hammer Tubes - 7x 5” Inch Hammer Bits (Used) - 1x 4” Inch Back Hammer - 1x 8” Inch Aircore Bit - 4” Inch Aircore Bits (2x New & 3x Used) - Blow Up Sub - 1x 4 ½” Inch PDC Bit - 6” Inch Casing Elevator Set - Diverter Box with 20x Rubbers - Stuffing Box - Rod Spanner to suit - Dig Out Sub Rig Truck Make: Volvo Year: 2012 - Twin Steer Option 1 – Water Bore Drilling Equipment (Additional $15,400 ex GST) - 12” Inch Blade Bit (Near New) - 7 7/8” Inch Blade Bit - 8” Inch Tri-Cone Med Formation (Near New) - 6” Inch Shreps Hammer with 6” Inch & 8” Inch Bits (New) - Adaptor Subs to suit - Rod Spanners to suit - Casing Elevators Option 2 – RC Rods (Additional $55,000 ex GST) - 180 Metres of RC 4” Inch Remet Rod String (New) Option 3 – Hooklift Truck + Bins ($55,000 ex GST) Truck Make: Isuzu Year: 2000 - Hooklift Truck Bins; 1st Bin: 6x5 Gardner Denver Mud Pump with Perkins Engine 2nd Bin: To carry PVC and Gravel 3rd Bin: To carry Water Suttles Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Make: Komatsu Model: WA 900-8 Year: 2020 Hours: 14,212 Wheel Loader Location: United States of America Learn More

Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More

Make: Sandvik Model: DC302R Year: 2013 Hours: 6,030 Engine Power: 62 kW Drifter: HL300 (8 kW) - Fully Reconditioned and Painted Self Propelled Drill Rig Location: Europe Learn More

Rig Make: Hydramaster Model: 2000 - Fully Tooled & Spares - Recently painted Truck Make: International Model: Acco Year: 1998 KM's: 506,309 Type: 4x2 Engine: Cummins 300 HP Gearbox: 9 Speed Tri Axle Trailer - Near New - Set up for cable tool equipment Condition: Good Truck Mounted Cable Tool Drill Rig Tri Axle Trailer Location: Queensland, Australia Learn More

Make: Gardner Denver Model: PZ-7 - Reconditioned but not fully rebuilt Quantity: 2 Skid Mounted Bare Mud Pumps Location: Canada Learn More

Rig Make: Schramm Model: 685 Year: 1996 Hours: 2,500 (Since Rebuild) Engine: Cummins K19 Accessories; - FOPS - Rod Rack - 4x Levelling Jacks - In Mast Make/Break Rod Break Out System - Rotating Cyclone Set Up on Metz Manipulator - Airdrill Maker Breaker - Air Spanner - KL Rod Handler Set to 4.5" Inch Pipe - Dual RC Swivel and Auto Blow Down - ROPS Air-Conditioned Drillers Cabin - Complete Re-Hose 11/25 - Fire Suppression Air Compressor Make: Sullair 1,150 CFM / 500 PSI Water Capacity: Approx. 500 Litres Dimensions; Height: 4.6 m Width: 4.0 m Track Mounted Drill Rig Location: Queensland, Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Make: Epiroc Model: DM-L Year: 2005 Hours: 8,453 Engine: Cummins QSX15 Tier 3 - 33.5" Inch Triple Grouser Tracks - 30' Foot Tower Carousel - Can be set up for 5.5" Inch or 6.25" Inch Rods - 4 or 5 Pieces Air End Track Mounted Rotary Drill Rig Location: United States of America Learn More

Make: Caterpillar Model: 16M Year: 2008 Hours: 37,752 (Frame) / 5,834 (After Overhaul) Engine: Caterpillar CAT C13 - Complete Overhaul in 2022 Motor Grader Location: United States of America Learn More

Rig Make: Hanjin Model: D&B-8D Year: 2016 Hours: 5,800 Pull: 6 Metres - 1x Set of NQ Jaws *New* - 1x Set of HQ Jaws *New* - Cameron Water Gauge *New* - Wrap Around Mast - SPT Hammer Included - Rod Racks - Suction Hose and 2x Double Braid 1" Inch Duffield Bypass Hoses - 5x 100 mm Augers and 1x Bit Plus Drive Sub - 1 1/2" Inch Centrifugal Pump and Hoses - Plus Camlocks *All New* - 36" Inch & 24" Inch Stilsons - Chain Wrench - 1.5 Metre NMLC Core Barrel Plus 5x 3 Metre NQ Rods - 2x Mud Tanks - 7x5' Foot Box Trailer Tracked Mounted Drill Rig Location: New South Wales, Australia Learn More

Make: Sandvik Model: UDR300D (DE740) Main Winch: 9 m Pull - 30 Tonne Pull Back - 2x Main Traverse Cylinders - Fully Hosed - 3.5 m Stroke - Vertically Stacking Monkey Board - New & Unused Dump Mast Location: Queensland, Australia Learn More