Search results for: 'boart gear high for state'

Rig Make: UDR Model: 650 Hours: 9,202 - Commissioned Mid 2023 - Onboard PTO Driven Air Compressor - New water pump - New fan belts - New radiator core - Recent service with oil & new filters - New rod & piston seals to main feed Ram - New Dump Mast Ram - New rods & seals to mast raise rams - New side shift ram - New break out ram - New rod crane raise ram - New hydraulic valve blocks in control cabinet for main pump & secondary pump controls - New micro control fine feed controller - Replaced majority of gauges with new - New main rotation shaft seals & speedy sleeves - New main rotation torque control cartridge - New hammer oiler pump - New seats & O rings in majority of valve banks Air Compressor - New Air / Oil separator filter - New Oil stop valve - New Castrol Aircoil 68 synthetic oil - New filters - Recently been serviced by Midcoast Compressors Truck Make: MAN Year: 1997 KM's: 200,000 Type: 8x8 Transmission: Recon 18 Speed Gear Box - Kevrek 1500 Hiab Crane with Winch & Umbilical Cord Remote - Radiator back flushed - New Water Pump - New Fan Belts - New brake boosters on every wheel - New four way valve - New valve on brake pedal - Rebuilt Truck Compressor - New air on drivers seat - New air valves on diff locks / cross locks - New clutch, fly wheel & pressure plate - New bearings & seals in Dana drive box - New oil pump on Dana drive box - New universals on tail shafts - New ram on power steering - New tyres all around - All ball joints on truck replaced that were needed, or new rubbers on them - Recently passed Pit Inspection - 7 months Rego as Plant - No need for overhang permits; within length Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Rig Make: Edson Model: Versadrill 300 Year: 1996 Engine: Hatze - 6x6 Multidrive Technology - Rotation head MR260 Rotation hollow spindle, single speed, dial in, rotation head around 120 rpm - Winching gear on back of mast for hollow augering - Can do diamond drilling if you were to change the hydraulic motor - Dump Mast - Near New Hydraulic Pump - 4x Leveling Jacks - Currently doing 80mtr holes at 4.5” - Client used to aircore with it, but currently set up doing mud - Used to do a lot of Geotech work, 6” hollow augering - Southern Cross Mud pump on the side - 3.2 mtr Stroke - 3 mtr Rods - Extension arm to run 6mtr casing into the ground Ute Make: Toyota Model: Landcruiser Year: 1990 KM's: 107,000 Ute Mounted Drill Rig Location: Western Australia Learn More

Rig Make: Boart Longyear Model: LF90 Year: 2008 Hours: 14,154 - Fitted with KWL 400 Head as Top Drive - Masts are locked at 6 Metre Rod Pull - Has been drilling in Iron Ore Truck Make: Tatra Year: 2008 KM's: 37,735 Type: 8x8 Truck Mounted Drill Rig Location: Western Australia Learn More

Engine: Deutz 3FL2011 - Base Frame to support all components; engine, pump, hydraulics & fuel tanks, etc. - Fuel Tank Capacity: 60 Litres - Access Ladder to Control Platform - Paint, Two Pack Evolution Yellow Hydraulics; - Pump Group Bosch Rexroth - Main Pump A10VO45 Variable Displacement - Pilot Pump 5.5 cc Gear Pump - Maximum Circuit Pressure: 160 Bar - Hydraulic Oil Capacity: 100 Litres - Return Filter: 10 Micron - Hydraulic Oil Cooler and Fan Grout Pump; Make: Bredel Model: SPX 50 - Brevini BR100NC Hydraulic Motor - Slurry Flow Range: 0-85 lpm - Maximum Pressure: 15 Bar - Adjustable Speed Control Mixing Tank; Capacity: 1,400 Litres - Hydraulic Powered Agitator - Baffle Plates inside the tank - 3" Inch Outlet to Slurry Pump - Grid on tank top for cement dispersion during mixing - Sandblasted and painted with 2 pack paint Poly Reel; Capacity: 600 metres - 40 mm PN16 SDR11 Poly Pipe, Blue Stripe, 3.7 mm Wall - Fabricated construction approx. 2.1 metres diameter - Hydraulic Drive via reduction gearbox and chain + sprocket final drive - Adjustable Speed Control: 1.5-30 m/min Control Platform; - Mounted near mixing tank - Engine controls, start, stop, throttle, etc. - Hydraulic controls for agitator, slurry pump and hose reel Dimensions; Length: 4.65 m Width: 2.35 m Hight: 2.5 m Weight: 3,500 kg approx. Skid Mounted Grouting Unit Location: Australia Learn More

Q80K - Top Head Drive - 0-8,328 Nm (6,142 ft/lbf) in low gear - High Gear 3.04:1 Ratio - Low Gear 12.61:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Gear train for High/Low Ratio Q150K - Top Head Drive - 0-14,324 Nm (10,564 ft/lbf) in low gear - High Gear 3:1 Ratio - Low Gear 22.5:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Planetary Gear set for High/Low Ratio Q280K - Top Head Drive - 0-28,000 Nm (20,651 ft/lbf) in low gear - High Gear 3:1 Ratio - Low Gear 22.5:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Dual Planetary Gear set for High/Low Ratio Rotation Head Gearboxes Location: Australia Learn More

Electrical Equipment - Panel Mount Display - 24 V 30/20 Replay - Suit Flowmeter Plug Hydraulic Equipment - Microfeed Rate Hydraulic Block - Check Cart Valve - Priority Cart Valve - 3 Way Directional Valve - Check 0.3 Bar Valve - Gear Flow Meter Penetration Rate Measuring System Sure Rate Location: Australia Learn More

Body Opening: 225 mm (8 3/4" Inch) OD - Fabricated High Tensile Steel Base Frame for increased strength and lighter unit weight - High Tensile Fabricated Lever Arms - Adjustable Connecting with Left & Right Hand Threads allowing accurate adjustment of jaw actuation - Cast Jaw Assemblies to suit most standard drill rod sizes - Light weight casting approx. 16 kg per jaw - Easily replaceable Gripper Inserts for NQ & HQ Jaw Sizes - RC Slips Table, Holders and Inserts to suit 3 1/2", 4" & 4 1/2" Rod Sizes - Changeable with Industry Standard Rod Clamps Rod Clamp Location: Australia Learn More

Model: FH3000 Engine: Cummins QSL Electronic @ 255 kW (342 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Maximum Speed: 55.5 m/min (182 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - 100% Theoretical Main Winch; - Maximum Pull: 226 kN (50,806 lbf) - Maximum Speed: 100 m/min (328 ft/min) - 2x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release - 9 Metre Rod Pull Capacity Wireline Winch; - Maximum Pull: 27 kN (6,069 lbf) - Rope Capacity: 3,000 Metres x 8 mm Rope - Maximum Speed: 450 m/min (1,476 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH2000 Engine: Caterpillar CAT C7.1 Electronic @ 205 kW (275 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Up: 50 m/min (164 ft/min) Down: 39 m/min (128 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - Bosch Rexroth A6VM160 Variable Displacement Motor - High Gear 3:1 & Low Gear 19.57:1 ratios - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube Bearings and Gears with filtered and cooled lubrication oil system Main Winch; - Maximum Pull: 156 kN (35,048 lbf) - 120 m/min (394 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - 28 mm Main Winch Rope - Safety Factor 3.35:1 (exceeds BS/EN791) - 1x Bosch Rexroth A6VM160 Variable Displacement Motors - 1x Brevini Planetary Reduction Gear Boxes - 1x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release Wireline Winch; - Mast Mounted - Maximum Pull: 25 kN (5,617 lbf) - Rope Capacity: 2,100 Metres x 8 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1300 Engine: Caterpillar CAT C7.1 Electronic @ 187 kW (250 HP) Pull Back: 115 kN (25,853 lbf) Actual Pull Down: 70 kN (15,736 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 1,300 m HQ Core: 885 m Open Hole 3 1/2" Inch Rods: 380 m RC 4 1/2" Inch: 220 m (Nominal) Traverse Speed; Up: 60 m/min (196.8 ft/min) Down: 56 m/min (183.7 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 8,087 Nm (6,111 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - High Gear 3.04:1 & Low Gear 12.61:1 ratios - Variable Displacement 160cc Hydraulic Motor - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube System with Cooler and Filter Main Winch; - Maximum Pull: 100 kN (10,000 lbf) - 120 m/min (393 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - Main Winch Rope - Safety Factor to Meet BS/EN791 - Planetary Reduction Gear Box & Brake - Variable Displacement Hydraulic Motor Drive Wireline Winch; - Deck Mounted - Maximum Pull: 15 kN (3,372 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1000 Pull Back: 97 kN (21,783 lbf) Pull Down: 45 kN (10,116 lbf) Water Pump: Standard FMC W1122BCD 140 lpm @ 1,000 psi Depth Capacity; NQ Core: 1,150 m HQ Core: 786 m HWT Core: 518 m RC 4" Inch: 198 m (Nominal) Engine Options; - John Deere Power Tech 6.8L @ 155 kW (208 HP) - Caterpillar CAT C6.6 ACERT - Cummins B5.9-173 Traverse Speed; Up: 47 m/min (154 ft/min) Down: 30 m/min (98 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 5,965 Nm (4,400 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - 100% Theoretical Main Winch; - Maximum Pull: 88.4 kN (19,870 lbf) - 55 m/min (180 ft/min) - Mast Top Mounted - 1x Multi Disc Brake Unit - Fail Safe Spring Activated - Hydraulic Pressure Release - Main Winch Rope - Safety Factor to Meet BS/EN791 - 6 Metre Rod Pull Capacity Wireline Winch; - Deck Mounted - Maximum Pull: 13.5 kN (3,044 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Maximum Speed: 342 m/min (1,124 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: 1750 Scout Engine: Perkins Diesel Torque: 2,500 Nm at 205 bar and 110 RPM Stroke: 1.75 m Pull-Out / Pull-Down: 1,100 kg Capacity (Guide Only): NQ - 60 m / 4" Inch Open Hole - 30 m / 3 1/2" Inch Auger - 15 m - Custom Toyota 33220 Tray - Direct Dive Auger Head with High Torque Head Motor and Fittings - Fine Feed Control - Auger Drive Sub (1 1/8" Inch Hex) - RHS Mast - Tilt Frame for Vehicle/Trailer Mounting - Hydraulic Tilt - Heavy Duty Pull-Down Chain - Nylon Idler Rollers - Standard Auger Guide - Standard Control Panel - Hydraulic Operation - Rain Hood for Motor & Lockable Cage for Spare Wheel & Motor - Remove Throttle and Stop - Water Filter for Fuel / Water Separation - Light Guard for Augers 500 mm to 1,800 mm - Oil Cooler - Simple Rack for Augers Options for Drill; - Hollow Spindle Head and Tooling for Fluid Drilling - 2 Levelling Jacks for Tray Mount Drills - Tilting Rack for Augers - Alternative Engine Options to suit existing fleet Toyota Landcruiser Upgrade Kit; - Roof Racks for Spare Tyre (31678) - Roof Rack Mounts Pair (31679) - GVM Upgrade Spring Kit @ 4,200 kg (Supply Only - 31680) - Bellows Suspension Kit (Supply Only - 31730) - Storage Box LH Under Deck (33249) - Storage Box RH Under Deck (33248) - Under Deck Water Tanks @ 29 Litres (33137) *Ready for mounting to a Toyota 79 Series Landcruiser Cab Chassis* Drill Rig Location: Australia Learn More

Make: Ariel Model: JGP2 Part Number: CL190390 Weight: 388.1 kg Brand New High Pressure Cooler Panels Location: Victoria, Australia Learn More

Make / Model: TL-400 Contains: - Tower - Flashlight - Headlight - Charger - Driver - Battery System D24-100 - USD Output, 5V 2A (2 Dock) for charging Headlight, Flashlight or Mobile Phone - 1-3 Battery Pack (1 Battery 30+ Hours extreme mode) - Height: 64.5 cm - 220 cm - Weight: 12.85 kg - One Man Operation - Self locking and 30 degree + up/down adjustable pole - Run Times > 10 hours (High output, 3 batteries) Application - Drilling - Construction - Maintenance - Events - Mining - Emergency - Infrastructure - Personal Control Board - Power Switch - Brightness - DIM+, DIM- - Battery Level - AC Plug - USB Output Light Brightness Area: 1,100 m2 5 m - 490 lux / 10 m - 120 lux / 20 m - 29 lux / 40 m - 7 lux Battery / AC 100-227V - AC 0-15,000 LM - High 8,000 LM - Medium 5,000 LM - Low 2,500 LM - Extreme 800 LM - Rate Power 28 wh - Rate Voltage 24.5 V - Rate Capacity 40 Ah - Working Temp: -10 to 50 degrees - Working Humidity: -20 to 95% Portable Light Tower Location: Queensland, Australia Learn More

Make: Ferrari Type: 360 Hours: Very Low Engine: Lombardini - 3 Forward and 3 Reverse Gears - Added Depth Control Wheels - Ideal for Professional Market Garden Rotary Hoe Location: Western Australia Learn More

Make: Hydco Model: 1000H Year: 2008 Hours: 4,304 Engine: Cummins 6CTA Onboard Air Compressor: Sullair 1,150 CFM / 350 PSI & 900 CFM / 500 PSI Compressor Hours: 819 Compressor Engine: Caterpillar CAT C15 - Setup for mainly RC however has the diamond capabilities & equipment - Rig has recently been completing RC holes to depths of 425 m coupled with the Aux Compressor Kit giving 2,400 CFM / 1,000 PSI Diamond Drilling Capacity; HQ: 1,000 m NQ: 1,500 m PQ: 600 m Features; - Harlsan Auto Blow Up and Blowdown - KL Rod Handler - Hydraulic Breakouts - Hydraulic Spanners - Safety Cage with Interlock - Quick Access Mountable Stuffing Box Assembly - Fire Suppression - Dust Suppression - FMC Bean Pump for Diamond Drilling - FMC Dual Pump for Water Injection - Hydraulic Foot Clamps - Diamond Drilling Safety Cage - Diamond Drilling Platform - Storage Area with Safety Rails and Access Ladders - Refurbished Cyclone - New Cone Splitter - New Track Chains and Rollers - 400x Metres of 4.5" Inch Remet Rods - Airdrill 670 Hammers & Bits - Other specific RC Gear Track Mounted Drill Rig Location: Western Australia Learn More

Make: Gardner Denver Model: PZ-7 Year: 2014 - Triplex w/ Forged Steel Fluid End & Quick Change Caps - 5M Pulsation Dampener - Oteco 3" Inch Shear Relief Valve - Pressure Gauge - Mission 6x5 Charge Pump - Fitted with 7" Inch Liners & Pistons - No Engine or Transmission Condition: Good Skid Mounted Mud Pump Location: United States of America Learn More

Make: FMC Model: L1122 Stroke Length: 2.75" Inch Piston Diameter: 2.75" Inch Frame Load Rating: 6,000 lbs Internal Gear Ratio: 3.6:1 Intermittent Duty Speed Rating: 1,275 RPM Continuous Duty Speed Rating: 900 RPM Standard Suction Size: 2.50" Inch NPT Standard Discharge Size: 1.25" Inch NPT Number of Pistons: 3 Horizontal Triplex Piston Pump Location: New South Wales, Australia Learn More

Make: Custom Model: 600 RRD Motor: 40 HP TEFC Pulling Capacity: 24,000 lbs Lifting Capacity: 24,000 lbs Down Thrust Capacity: 12,500 lbs Rotational Torque: 6,500 ft/lbs Load Sensing Power Limiting Pump: 45 GPM @ 1,700 PSI Load Sensing Diesel Pump: 15 GPM @ 3,500 PSI Fast Feed: 14.79 GPM @ 2,500 PSI Slow Feed: 6.2 GPM @ 2,500 PSI Traction Hydraulic Motor: 14 HP each at 4,000 MASL (Using Diesel Drive) Max. Drilling Air Pressure: 400 PSI Feed Cylinders Combined Bore: 9.8 sq inch Features; - Lubricator - Water Pump - Robust Mine Proven Construction - High Torque Rotation Head - Reversable Heavy Duty Mast - Efficient Electric/Hydraulic Drive - Fully Hydraulic Operation - Compact Size - Fully Variable Rotation Speed (0-24 RPM) Hydraulically Operated Crawlers - Remotely Operated Hydraulic Console for flexibility - Sting Cylinder - Dual Heavy Duty Feed System - 90 Degree Tilt Out Rotation Head - Longitudinal Shift - Side Shift - NEMA 4 - Air Motors for travelling Track Mounted Drill Rig Location: Canada Learn More

Wireline Cable: 1,000 m + - Hydraulic Motor - Double Sheave Wheel - Assembly for High Tonnage Winch - Top of Mast Assembly Design Wireline Winch Crown Wheel Assembly Location: Victoria, Australia Learn More