Search results for: 'boart gear hire for size'

Size: 12 1/4" Inch - Milled Teeth - Sealed Bearing Condition: Good Rock Roller Bit Location: Western Australia Learn More

Rig Make: UDR Model: 650 Hours: 9,202 - Commissioned Mid 2023 - Onboard PTO Driven Air Compressor - New water pump - New fan belts - New radiator core - Recent service with oil & new filters - New rod & piston seals to main feed Ram - New Dump Mast Ram - New rods & seals to mast raise rams - New side shift ram - New break out ram - New rod crane raise ram - New hydraulic valve blocks in control cabinet for main pump & secondary pump controls - New micro control fine feed controller - Replaced majority of gauges with new - New main rotation shaft seals & speedy sleeves - New main rotation torque control cartridge - New hammer oiler pump - New seats & O rings in majority of valve banks Air Compressor - New Air / Oil separator filter - New Oil stop valve - New Castrol Aircoil 68 synthetic oil - New filters - Recently been serviced by Midcoast Compressors Truck Make: MAN Year: 1997 KM's: 200,000 Type: 8x8 Transmission: Recon 18 Speed Gear Box - Kevrek 1500 Hiab Crane with Winch & Umbilical Cord Remote - Radiator back flushed - New Water Pump - New Fan Belts - New brake boosters on every wheel - New four way valve - New valve on brake pedal - Rebuilt Truck Compressor - New air on drivers seat - New air valves on diff locks / cross locks - New clutch, fly wheel & pressure plate - New bearings & seals in Dana drive box - New oil pump on Dana drive box - New universals on tail shafts - New ram on power steering - New tyres all around - All ball joints on truck replaced that were needed, or new rubbers on them - Recently passed Pit Inspection - 7 months Rego as Plant - No need for overhang permits; within length Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Rig Make: Edson Model: Versadrill 300 Year: 1996 Engine: Hatze - 6x6 Multidrive Technology - Rotation head MR260 Rotation hollow spindle, single speed, dial in, rotation head around 120 rpm - Winching gear on back of mast for hollow augering - Can do diamond drilling if you were to change the hydraulic motor - Dump Mast - Near New Hydraulic Pump - 4x Leveling Jacks - Currently doing 80mtr holes at 4.5” - Client used to aircore with it, but currently set up doing mud - Used to do a lot of Geotech work, 6” hollow augering - Southern Cross Mud pump on the side - 3.2 mtr Stroke - 3 mtr Rods - Extension arm to run 6mtr casing into the ground Ute Make: Toyota Model: Landcruiser Year: 1990 KM's: 107,000 Ute Mounted Drill Rig Location: Western Australia Learn More

Model: 150N Engine: John Deere / FPT Iveco / Kirloskar / Deutz Pull Up Force: 5,000 kg Pull Down Force: 3,750 kg Tool Winch Hoisting Capacity: 2,500 kg (Bare Drum) Wireline Winch Hoisting Capacity: 500 kg (Bare Drum) Diamond Core Drilling Capacity; NQ Size: 150 m HQ Size: 90 m PQ Size: 60 m Water Pump; Max Flow: 120 LPM Max Pressure: 30 bar Type: Triplex Piston Pump Track Mounted Multi Purpose Drill Rig Location: United Arab Emirates Learn More

Model: 75N Engine: Kirloskar / Deutz / John Deere Pull Up Force: 2,500 kg Pull Down Force: 2,500 kg Tool Winch Hoisting Capacity: 1,500 kg Diamond Core Drilling Capacity; NQ Size: 75 m HQ Size: 45 m PQ Size: 30 m Mud Rotary; 30 m @ 150 mm Diameter Auger Drilling; 20 m @ 150 mm Diameter 4 m @ 300 mm Diameter Water Pump; Max Flow: 85 LPM / 140 LPM Max Pressure: 30 bar / 18 bar Type: Triplex Piston Pump / Progressive Cavity Pump Compact Geotechnical Drill Rig Location: United Arab Emirates Learn More

Rig Make: Boart Longyear Model: LF90 Year: 2008 Hours: 14,154 - Fitted with KWL 400 Head as Top Drive - Masts are locked at 6 Metre Rod Pull - Has been drilling in Iron Ore Truck Make: Tatra Year: 2008 KM's: 37,735 Type: 8x8 Truck Mounted Drill Rig Location: Western Australia Learn More

Includes; - Kitchen - Lunch Room / Work Space Room - Storage Dual-Axle Van Location: Australia Learn More

Generator: Honda 2kVA Dimensions; Length: 4 Metres (Inc. Trailer) Width: 1.6 Metres Height: 2.5 Metres Cold Room: 1.2 m x 1.2 m x 1.8 m - Fully Insured & Ready to Go - Mobile- Galvanised Trailer - 2,500 Litre Cold Room - Holds 4x Kegs with 4x Taps (2 Either Side) - Drip Trays on Both Sides - Extra Cold Room Storage - Pull Out Shade Cloths on Both Sides - Party Hire - Camping - Beach Party (Trailer is Purpose Built) - Functions - Corporate - Event Management - Fundraisers Mobile Keg & Chill Cold Room Trailer Location: Queensland, Australia Learn More

Make: Mole Pioneer Model: P400S 450HQ Hours: 2,940 Engine: Perkins 119 kW Diesel - Onboard W1122 Bean Pump Rotation Head Model: KL400 Top Drive Stroke: 1,200 mm Drilling Angle: 90 degrees vertical to 45 degrees horizontal Drilling Depth Capacity B Size: 900 metres N Size: 700 metres H Size: 450 metres P Size: 275 metres Truck Make: Ford Model: Cargo Series KM's: 25,372 Year: 1985 Type: 6x4 Condition: Good *For more information, please contact us* Mole Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Includes; - Kitchen - Lunch Room / Work Station Room - Generator - 2x Toilets Tri-Axle Van Location: Australia Learn More

Engine: Deutz 3FL2011 - Base Frame to support all components; engine, pump, hydraulics & fuel tanks, etc. - Fuel Tank Capacity: 60 Litres - Access Ladder to Control Platform - Paint, Two Pack Evolution Yellow Hydraulics; - Pump Group Bosch Rexroth - Main Pump A10VO45 Variable Displacement - Pilot Pump 5.5 cc Gear Pump - Maximum Circuit Pressure: 160 Bar - Hydraulic Oil Capacity: 100 Litres - Return Filter: 10 Micron - Hydraulic Oil Cooler and Fan Grout Pump; Make: Bredel Model: SPX 50 - Brevini BR100NC Hydraulic Motor - Slurry Flow Range: 0-85 lpm - Maximum Pressure: 15 Bar - Adjustable Speed Control Mixing Tank; Capacity: 1,400 Litres - Hydraulic Powered Agitator - Baffle Plates inside the tank - 3" Inch Outlet to Slurry Pump - Grid on tank top for cement dispersion during mixing - Sandblasted and painted with 2 pack paint Poly Reel; Capacity: 600 metres - 40 mm PN16 SDR11 Poly Pipe, Blue Stripe, 3.7 mm Wall - Fabricated construction approx. 2.1 metres diameter - Hydraulic Drive via reduction gearbox and chain + sprocket final drive - Adjustable Speed Control: 1.5-30 m/min Control Platform; - Mounted near mixing tank - Engine controls, start, stop, throttle, etc. - Hydraulic controls for agitator, slurry pump and hose reel Dimensions; Length: 4.65 m Width: 2.35 m Hight: 2.5 m Weight: 3,500 kg approx. Skid Mounted Grouting Unit Location: Australia Learn More

Q80K - Top Head Drive - 0-8,328 Nm (6,142 ft/lbf) in low gear - High Gear 3.04:1 Ratio - Low Gear 12.61:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Gear train for High/Low Ratio Q150K - Top Head Drive - 0-14,324 Nm (10,564 ft/lbf) in low gear - High Gear 3:1 Ratio - Low Gear 22.5:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Planetary Gear set for High/Low Ratio Q280K - Top Head Drive - 0-28,000 Nm (20,651 ft/lbf) in low gear - High Gear 3:1 Ratio - Low Gear 22.5:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Dual Planetary Gear set for High/Low Ratio Rotation Head Gearboxes Location: Australia Learn More

Electrical Equipment - Panel Mount Display - 24 V 30/20 Replay - Suit Flowmeter Plug Hydraulic Equipment - Microfeed Rate Hydraulic Block - Check Cart Valve - Priority Cart Valve - 3 Way Directional Valve - Check 0.3 Bar Valve - Gear Flow Meter Penetration Rate Measuring System Sure Rate Location: Australia Learn More

Body Opening: 225 mm (8 3/4" Inch) OD - Fabricated High Tensile Steel Base Frame for increased strength and lighter unit weight - High Tensile Fabricated Lever Arms - Adjustable Connecting with Left & Right Hand Threads allowing accurate adjustment of jaw actuation - Cast Jaw Assemblies to suit most standard drill rod sizes - Light weight casting approx. 16 kg per jaw - Easily replaceable Gripper Inserts for NQ & HQ Jaw Sizes - RC Slips Table, Holders and Inserts to suit 3 1/2", 4" & 4 1/2" Rod Sizes - Changeable with Industry Standard Rod Clamps Rod Clamp Location: Australia Learn More

Model: FH3000 Engine: Cummins QSL Electronic @ 255 kW (342 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Maximum Speed: 55.5 m/min (182 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - 100% Theoretical Main Winch; - Maximum Pull: 226 kN (50,806 lbf) - Maximum Speed: 100 m/min (328 ft/min) - 2x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release - 9 Metre Rod Pull Capacity Wireline Winch; - Maximum Pull: 27 kN (6,069 lbf) - Rope Capacity: 3,000 Metres x 8 mm Rope - Maximum Speed: 450 m/min (1,476 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH2000 Engine: Caterpillar CAT C7.1 Electronic @ 205 kW (275 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Up: 50 m/min (164 ft/min) Down: 39 m/min (128 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - Bosch Rexroth A6VM160 Variable Displacement Motor - High Gear 3:1 & Low Gear 19.57:1 ratios - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube Bearings and Gears with filtered and cooled lubrication oil system Main Winch; - Maximum Pull: 156 kN (35,048 lbf) - 120 m/min (394 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - 28 mm Main Winch Rope - Safety Factor 3.35:1 (exceeds BS/EN791) - 1x Bosch Rexroth A6VM160 Variable Displacement Motors - 1x Brevini Planetary Reduction Gear Boxes - 1x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release Wireline Winch; - Mast Mounted - Maximum Pull: 25 kN (5,617 lbf) - Rope Capacity: 2,100 Metres x 8 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1300 Engine: Caterpillar CAT C7.1 Electronic @ 187 kW (250 HP) Pull Back: 115 kN (25,853 lbf) Actual Pull Down: 70 kN (15,736 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 1,300 m HQ Core: 885 m Open Hole 3 1/2" Inch Rods: 380 m RC 4 1/2" Inch: 220 m (Nominal) Traverse Speed; Up: 60 m/min (196.8 ft/min) Down: 56 m/min (183.7 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 8,087 Nm (6,111 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - High Gear 3.04:1 & Low Gear 12.61:1 ratios - Variable Displacement 160cc Hydraulic Motor - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube System with Cooler and Filter Main Winch; - Maximum Pull: 100 kN (10,000 lbf) - 120 m/min (393 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - Main Winch Rope - Safety Factor to Meet BS/EN791 - Planetary Reduction Gear Box & Brake - Variable Displacement Hydraulic Motor Drive Wireline Winch; - Deck Mounted - Maximum Pull: 15 kN (3,372 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1000 Pull Back: 97 kN (21,783 lbf) Pull Down: 45 kN (10,116 lbf) Water Pump: Standard FMC W1122BCD 140 lpm @ 1,000 psi Depth Capacity; NQ Core: 1,150 m HQ Core: 786 m HWT Core: 518 m RC 4" Inch: 198 m (Nominal) Engine Options; - John Deere Power Tech 6.8L @ 155 kW (208 HP) - Caterpillar CAT C6.6 ACERT - Cummins B5.9-173 Traverse Speed; Up: 47 m/min (154 ft/min) Down: 30 m/min (98 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 5,965 Nm (4,400 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - 100% Theoretical Main Winch; - Maximum Pull: 88.4 kN (19,870 lbf) - 55 m/min (180 ft/min) - Mast Top Mounted - 1x Multi Disc Brake Unit - Fail Safe Spring Activated - Hydraulic Pressure Release - Main Winch Rope - Safety Factor to Meet BS/EN791 - 6 Metre Rod Pull Capacity Wireline Winch; - Deck Mounted - Maximum Pull: 13.5 kN (3,044 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Maximum Speed: 342 m/min (1,124 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Hammer Size: 12" Inch Drill Bit Size: 20" Inch - With SD12 Shank (Unused) Location: Queensland, Australia Learn More

Make: Gardner Denver Model: 8x5 - Hydraulic Driven Trailer Mounted Mud Pump Location: New South Wales, Australia Learn More