Search results for: 'hire for size dump creek punta good fl'

Set Ascending Direction

240 items

per page
Did you mean
hire for sale dump creek punta good fl
high for size dump creek punta good fl
Related search terms
hire for sale statesboro ga
hire for sale in dual ray black
hire for sale alpena corner
hire for sale in johnson core tx
hire for sale in dm ram bean
  1. 2006 Caterpillar CAT C15 Skid Mounted Engine ($59,000 ex GST) (sale-ehub4016)
    For Sale
    $59,000.00
    Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More
    Machine hours

    1,400

    KILOMETERS N/A
    YEAR

    2006

    BRAND

    Caterpillar CAT

    LOCATION

    Queensland, Australia

    MODEL

    C15

  2. 2010 Ubuilt Cassady CTU Coil Tubing Unit Mounted on 2005 Ensign Carrier ($295,000 ex GST) (sale-ehub4015)
    For Sale
    $295,000.00
    Make / Model: Ubuilt Cassady CTU Carrier & Booster OD Year: 2010 Hours: 310 Engine: John Deere ATM: 61,500 kg Trailer Make: Ensign Model: C.T. 1000 Year: 2005 Tyre Size: 275/70R22.5 Rim Size: 8.25x22.5 Axle Group Load Carrying Capacity: 37,500 kg - Handrail and Stair Upgrade by Obadare CTU Coil Tubing Unit Carrier Mounted Location: Queensland, Australia Learn More
    Machine hours N/A KILOMETERS N/A
    YEAR

    2010

    BRAND

    N/A

    LOCATION

    Queensland, Australia

    MODEL

    Ubuilt Cassady CTU Carrier & Booster OD

  3. 2007 Drill Rig Mounted on 2007 Isuzu FTS 750 4x4 Table Top Truck ($145,000 ex GST) (sale-ehub4003)
    For Sale
    $145,000.00
    Rig Year: 2007 Hours: 3,000 Engine: Caterpillar (85 HP) Stroke: 3,300 mm - 2 Speed Head Rotation Torque: 2,500/450 Nm Rotation Speed: 140/750 RPM Pullback: 7,000 kg Pull Down: 4,000 kg - Set up for Geotechnical Drilling with Auto SPT - 1x Main Winch - 2x Wireline Winch - Mono Pump - Four Jack Legs - Drilling Rods, Alloy Mud Tanks, Accessories for 50 m (All in Good Condition) Truck Make: Isuzu Model: FTS 750 Year: 2007 KM's: 55,000 Type: 4x4 Table Top Truck Mounted Drill Rig Location: Queensland, Australia Learn More
    Machine hours

    3,000

    KILOMETERS

    55,000

    YEAR

    2007

    BRAND

    N/A

    LOCATION

    Queensland, Australia

    MODEL

    N/A

  4. 2012 ZJ50D/3150 Drill Rig (FOR HIRE/RENT - POA) (hire-ehub3991)
    For Hire
    Rig Model: ZJ50D/3150 Year: 2012 Mast Model: JJ315/45-K6 Substructure Model: DZ3159-S Drawworks Model: JC50D Power: 1,500 HP Rotary Table Model: ZP-375 Full Opening: 37.5” Inch Rotary Speed: 300 RPM Mud Pump Power: 1,600 HP Stroke: 120 RPM Working Pressure: 5,000 PSI Quantity: 2x Mud Tank Shaker Tank: 25 CuM Intermediate Tank: 40 CuM Suction and Mixing Tank: 20 CuM Solids Control - 3x Shale Shaker - 1x Mud Cleaner - 1x Centrifuge Drill Rig Location: Japan Learn More
    Machine hours N/A KILOMETERS N/A
    YEAR N/A BRAND

    N/A

    LOCATION

    Japan

    MODEL

    ZJ50D/3150

  5. 10x 2021 Komatsu HD465-7E0 Dump Trucks (POA) (sale-ehub3989)
    For Sale
    $0.00
    Make: Komatsu Model: HD465-7E0 Year: 2021 Hours: 9,000 - 17,280 Quantity: 10 Dump Trucks Location: China Learn More
    Machine hours

    9,000 - 17,280

    KILOMETERS N/A
    YEAR

    2021

    BRAND

    Komatsu

    LOCATION

    China

    MODEL

    HD465-7E0

  6. 5x 2018 & 3x 2019 Caterpillar CAT 745 Dump Trucks (POA) (sale-ehub3984)
    For Sale
    $0.00
    Make: Caterpillar Model: 745 Year: 2018 & 2019 Quantity: 3x 2019 / 5x 2018 - No EPA or CE Condition: Excellent & Good Tyres Dump Trucks Location: Chile Learn More
    Machine hours N/A KILOMETERS N/A
    YEAR

    2018

    BRAND

    Caterpillar

    LOCATION

    Chile

    MODEL

    745

  7. 2007 Atlas Copco RD20-III Carrier Mounted Drill Rig (POA) (sale-ehub3983)
    For Sale
    $0.00
    Make: Atlas Copco Model: RD20-III Year: 2007 Hours: 7,500 - In Good Working Order - Full Service Report Available This used 2007 RD20 Range III Atlas Copco Rig is a powerful and versatile drilling machine, ideal for a wide range of applications. Equipped with on IR 1,250 CFM / 350 PSI Air Compressor, this rig delivers exceptional performance and efficiency. Powered by a robust CAT C13 engine, the rig ensures smooth operation and ample power. The Cummins QSK19 deck engine further enhances its performance capabilities, delivering 755 HP for demanding drilling tasks. With a substantial pullback capacity of 120,000 lbs (54,446 kg), this rig can handle tough drilling conditions with ease. Mounted on a crane carrier truck, this RD20 III Atlas Copco Rig provides excellent mobility and stability. The rig has been meticulously maintained to ensure optimal condition and longevity. Its clean appearance reflects the owner’s commitment to proper care and maintenance. Carrier Mounted Drill Rig Location: New South Wales, Australia Learn More
    Machine hours

    7,500

    KILOMETERS N/A
    YEAR

    2007

    BRAND

    Atlas Copco

    LOCATION

    New South Wales, Australia

    MODEL

    RD20-III

  8. 2022 Rebuilt SPM Weir TWS2250 Skid Mounted Jack Up Frac Mud Pump (FOR HIRE/RENT - POA) (hire-ehub3982)
    For Sale
    $0.00
    Make: SPM Weir Model: TWS2250 Year: 2022 (Reman Rebuild) Hours: Approx. 7,000 Engine: Caterpillar CAT C32 (Rated @ 1,350 HP) Transmission: Allison 8000 Series Auto (DP8962R) Dimensions; Length: 9,135 mm (Overall) Width: 2,505 mm Height: 2,615 mm (On Ground) Height: 4,280 mm (Raised) Weight: 20,000 kg - When raised has enough height for a trailer of 1,500 mm to drive underneath Skid Mounted Jack Up Frac Mud Pump Location: Queensland, Australia Learn More
    Machine hours

    Approx. 7,000

    KILOMETERS N/A
    YEAR N/A BRAND

    N/A

    LOCATION

    Queensland, Australia

    MODEL

    SPM Weir TWS2250

  9. Hydramaster 2000 Cable Tool Drill Rig Mounted on 1998 International Acco 4x2 Truck & Tri Axle Trailer ($99,000 ex GST) (sale-ehub3957)
    For Sale
    $99,000.00
    Rig Make: Hydramaster Model: 2000 - Fully Tooled & Spares - Recently painted Truck Make: International Model: Acco Year: 1998 KM's: 506,309 Type: 4x2 Engine: Cummins 300 HP Gearbox: 9 Speed Tri Axle Trailer - Near New - Set up for cable tool equipment Condition: Good Truck Mounted Cable Tool Drill Rig Tri Axle Trailer Location: Queensland, Australia Learn More
    Machine hours N/A KILOMETERS

    506,309

    YEAR

    1998

    BRAND

    Hydramaster

    LOCATION

    Queensland, Australia

    MODEL

    2000

  10. 2012 Komatsu HD465-7E0 Dump Truck (POA) (sale-ehub3947)
    For Sale
    $0.00
    Make: Komatsu Model: HD465-7E0 Year: 2012 Hours: 10,604 Dump Truck Location: Chile Learn More
    Machine hours

    10,604

    KILOMETERS N/A
    YEAR

    2012

    BRAND

    Komatsu

    LOCATION

    Chile

    MODEL

    HD465-7E0

  11. 2012 Komatsu HD465-7E0 Dump Truck (POA) (sale-ehub3946)
    For Sale
    $0.00
    Make: Komatsu Model: HD465-7E0 Year: 2012 Hours: 7,883 Dump Truck Location: Chile Learn More
    Machine hours

    7,883

    KILOMETERS N/A
    YEAR

    2012

    BRAND

    Komatsu

    LOCATION

    Chile

    MODEL

    HD465-7E0

  12. 2012 Komatsu HD465-7E0 Dump Truck (POA) (sale-ehub3945)
    For Sale
    $0.00
    Make: Komatsu Model: HD465-7E0 Year: 2012 Hours: 9,534 Dump Truck Location: Chile Learn More
    Machine hours

    9,534

    KILOMETERS N/A
    YEAR

    2012

    BRAND

    Komatsu

    LOCATION

    Chile

    MODEL

    HD465-7E0

  13. 2012 Komatsu HD465-7E0 Dump Truck (POA) (sale-ehub3944)
    For Sale
    $0.00
    Make: Komatsu Model: HD465-7E0 Year: 2012 Hours: 9,885 Dump Truck Location: Chile Learn More
    Machine hours

    9,885

    KILOMETERS N/A
    YEAR

    2012

    BRAND

    Komatsu

    LOCATION

    Chile

    MODEL

    HD465-7E0

  14. 2012 Komatsu HD465-7E0 Dump Truck (POA) (sale-ehub3943)
    For Sale
    $0.00
    Make: Komatsu Model: HD465-7E0 Year: 2012 Hours: 10,150 Dump Truck Location: Chile Learn More
    Machine hours

    10,150

    KILOMETERS N/A
    YEAR

    2012

    BRAND

    Komatsu

    LOCATION

    Chile

    MODEL

    HD465-7E0

  15. 2007 Hydrapower Explorer 500 Drill Rig Mounted on 2005 MAN M2000 Truck (POA) (sale-ehub3938)
    For Sale
    $0.00
    Rig Make: Hydrapower Model: Explorer 500 Year: 2007 Hours: 6,700 Engine: Cummins CPAK-6BTA Turbo After Cooled 6 Cylinder (176 HP @ 2,500 RPM) Rig Hydraulics; - Sauer Danfoss proportionally controlled control valves - Sauer closed loop pump on Rotary Drive Sauer open loop pump on auxiliary functions Rotary Drive; - Hydrapower Gearbox - Steel Casing with floating hollow spindle and hydraulic head lock and swing - Two Speed, 0 - 225 RPM & 0 - 966 RPM - Low speed torque to 4150 Nm - High speed torque to 966 Nm Head Travel: 6.8 m Main Winch; -Max. Pull: 4,200 kg -Max. Line Speed: 28 m/min Wireline Winch; Max. Pull: 780 kg Max. Line Speed: 83 m/min Pulldown; - Electrically controlled with dial for speed control Pull Down Capacity: 7000 kg Pull Out Capacity: 11,500 kg Mast; - Fitted with 2.0 m mast dump for angle drilling - Standard length is 10 m, supplied with hydraulically operated breakout spanner and top pulley swivel - Supplied with hydraulic circuit with quick-connect couplings for optional breakout table - Brakeout Table with Split Type Table - Bean Pump - 5x6 Gardner Denver Mud Pump (Hydraulic Driven) Truck Make: MAN Model: M2000 Year: 2005 KM's: 75,000 - Not registered - Some gearbox problems Truck Mounted Drill Rig Location: New South Wales, Australia Learn More
    Machine hours

    6,700

    KILOMETERS

    75,000

    YEAR

    2007

    BRAND

    Hydrapower

    LOCATION

    New South Wales, Australia

    MODEL

    Explorer 500

  16. 2012 Caterpillar CAT 775G Truck with MEGA Water Tank (POA) (sale-ehub3926)
    For Sale
    $0.00
    Make: Caterpillar Model: 775G Year: 2012 Hours: 8,737 Water Tank: MEGA Condition: Very Good Water Tank Truck Location: Chile Learn More
    Machine hours

    8,737

    KILOMETERS N/A
    YEAR

    2012

    BRAND

    Caterpillar

    LOCATION

    Chile

    MODEL

    775G

  17. 2013 Caterpillar CAT 777G Truck with Mega TT20 20,000 Gallon Water Tank (POA) (sale-ehub3925)
    For Sale
    $0.00
    Make: Caterpillar Model: 777G Year: 2013 Hours: 5,575 Condition: Very Good Water Tank Make: Mega Model: TT20 Gallons: 20,000 Water Tank Truck Location: Chile Learn More
    Machine hours

    5,575

    KILOMETERS N/A
    YEAR

    2013

    BRAND

    Caterpillar

    LOCATION

    Chile

    MODEL

    777G

  18. Mud Puppy MP-255-2SC Mud Recycler Pump Mounted on Hydraulic Jack Up Rod Sloop (FOR HIRE/RENT - POA) (hire-ehub3349)
    For Hire
    Make: Mud Puppy Model: MP-255-2SC - Mounted on Hydraulic Jack Up Rod Sloop Mud Recycler Pump Location: New South Wales, Australia Learn More
    Machine hours N/A KILOMETERS N/A
    YEAR N/A BRAND

    Mud Puppy

    LOCATION

    New South Wales, Australia

    MODEL

    MP-255-2SC

  19. S Reps 750 Gear Package ($8,000 ex GST) (sale-ehub3900)
    For Sale
    $8,000.00
    Includes; - 2x Complete Hammers (1x with a Hole Opener) - 1x Hammer in parts (Can Assemble with New Casing) - 17x Various Sized Shrouds (Mostly New) - 10x Bits (5x New & 5x Had One Run but Nearly New) - 7x Hammer Tubes - 4.5" Inch Remet to Metzke Hammer Adaptor and Inner Tubes - Various Other Spares S Reps 750 Gear Package Location: Western Australia Learn More
    Machine hours N/A KILOMETERS N/A
    YEAR N/A BRAND

    N/A

    LOCATION

    Western Australia

    MODEL

    See Description

  20. Sandvik DD420 Underground Mining Truck Cooler Pack ($2,500 ex GST) (sale-ehub3898)
    For Sale
    $2,500.00
    Make: Sandvik Model: DD420 - Was from Running Machine Condition: Good Cooler Pack Location: Western Australia Learn More
    Machine hours N/A KILOMETERS N/A
    YEAR N/A BRAND

    Sandvik

    LOCATION

    Western Australia

    MODEL

    DD420

Set Ascending Direction

240 items

per page