Search results for: 'hire for size in del ram bean'

Size: 12 1/4" Inch - TCI - Sealed Bearing Condition: Used Rock Roller Bit Location: Western Australia Learn More

Size: 12 1/4" Inch - Milled Teeth - Sealed Bearing Condition: Good Rock Roller Bit Location: Western Australia Learn More

Rig Make: UDR Model: 650 Hours: 9,202 - Commissioned Mid 2023 - Onboard PTO Driven Air Compressor - New water pump - New fan belts - New radiator core - Recent service with oil & new filters - New rod & piston seals to main feed Ram - New Dump Mast Ram - New rods & seals to mast raise rams - New side shift ram - New break out ram - New rod crane raise ram - New hydraulic valve blocks in control cabinet for main pump & secondary pump controls - New micro control fine feed controller - Replaced majority of gauges with new - New main rotation shaft seals & speedy sleeves - New main rotation torque control cartridge - New hammer oiler pump - New seats & O rings in majority of valve banks Air Compressor - New Air / Oil separator filter - New Oil stop valve - New Castrol Aircoil 68 synthetic oil - New filters - Recently been serviced by Midcoast Compressors Truck Make: MAN Year: 1997 KM's: 200,000 Type: 8x8 Transmission: Recon 18 Speed Gear Box - Kevrek 1500 Hiab Crane with Winch & Umbilical Cord Remote - Radiator back flushed - New Water Pump - New Fan Belts - New brake boosters on every wheel - New four way valve - New valve on brake pedal - Rebuilt Truck Compressor - New air on drivers seat - New air valves on diff locks / cross locks - New clutch, fly wheel & pressure plate - New bearings & seals in Dana drive box - New oil pump on Dana drive box - New universals on tail shafts - New ram on power steering - New tyres all around - All ball joints on truck replaced that were needed, or new rubbers on them - Recently passed Pit Inspection - 7 months Rego as Plant - No need for overhang permits; within length Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Model: 150N Engine: John Deere / FPT Iveco / Kirloskar / Deutz Pull Up Force: 5,000 kg Pull Down Force: 3,750 kg Tool Winch Hoisting Capacity: 2,500 kg (Bare Drum) Wireline Winch Hoisting Capacity: 500 kg (Bare Drum) Diamond Core Drilling Capacity; NQ Size: 150 m HQ Size: 90 m PQ Size: 60 m Water Pump; Max Flow: 120 LPM Max Pressure: 30 bar Type: Triplex Piston Pump Track Mounted Multi Purpose Drill Rig Location: United Arab Emirates Learn More

Model: 75N Engine: Kirloskar / Deutz / John Deere Pull Up Force: 2,500 kg Pull Down Force: 2,500 kg Tool Winch Hoisting Capacity: 1,500 kg Diamond Core Drilling Capacity; NQ Size: 75 m HQ Size: 45 m PQ Size: 30 m Mud Rotary; 30 m @ 150 mm Diameter Auger Drilling; 20 m @ 150 mm Diameter 4 m @ 300 mm Diameter Water Pump; Max Flow: 85 LPM / 140 LPM Max Pressure: 30 bar / 18 bar Type: Triplex Piston Pump / Progressive Cavity Pump Compact Geotechnical Drill Rig Location: United Arab Emirates Learn More

Includes; - Kitchen - Lunch Room / Work Space Room - Storage Dual-Axle Van Location: Australia Learn More

Generator: Honda 2kVA Dimensions; Length: 4 Metres (Inc. Trailer) Width: 1.6 Metres Height: 2.5 Metres Cold Room: 1.2 m x 1.2 m x 1.8 m - Fully Insured & Ready to Go - Mobile- Galvanised Trailer - 2,500 Litre Cold Room - Holds 4x Kegs with 4x Taps (2 Either Side) - Drip Trays on Both Sides - Extra Cold Room Storage - Pull Out Shade Cloths on Both Sides - Party Hire - Camping - Beach Party (Trailer is Purpose Built) - Functions - Corporate - Event Management - Fundraisers Mobile Keg & Chill Cold Room Trailer Location: Queensland, Australia Learn More

Make: Mole Pioneer Model: P400S 450HQ Hours: 2,940 Engine: Perkins 119 kW Diesel - Onboard W1122 Bean Pump Rotation Head Model: KL400 Top Drive Stroke: 1,200 mm Drilling Angle: 90 degrees vertical to 45 degrees horizontal Drilling Depth Capacity B Size: 900 metres N Size: 700 metres H Size: 450 metres P Size: 275 metres Truck Make: Ford Model: Cargo Series KM's: 25,372 Year: 1985 Type: 6x4 Condition: Good *For more information, please contact us* Mole Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Make: Hydrapower - Rams have been resealed but never used Footclamps Location: Queensland, Australia Learn More

Includes; - Kitchen - Lunch Room / Work Station Room - Generator - 2x Toilets Tri-Axle Van Location: Australia Learn More

Drill Rig Make: Chicago Pneumatic Model: CP650 Year: 1981 Engine: Caterpillar CAT 3406 Onboard Air Compressor: GHH 825 CFM / 350 PSI Twin Screw Injection Pump: Comet APS 71 ltr/min @ 580 PSI Casing Driver: 612 Banger 6" Inch - 12" Inch Winch: 1/2" Inch 7,000 lbs Extendable Rod Handling Jib Hole Capacity: 6" Inch - 12" Inch 500 m 4 1/2" Inch Rods Capacity; Pull Down: 21,000 lbs Pull Back: 55,000 lbs 5 1/2" Inch Heavy Hoist Rams 73 ft/min Rapid Feed - 160 Pitch Chains Levelling Jacks; Front: 1 x 5" Inch x 48" Inch Stroke Rear: 2 x 5" Inch x 36" Inch Stroke Top Drive Rotary; 0-152 RPM - 76,000 lb Torque Twin Dynex Motors R/C Head - 7 m Travel Carrier Type: 6x4 Engine: Caterpillar CAT 3208 @ 210 HP Crane Carrier Carrier Mounted Water Well Drill Rig Location: New Zealand Learn More

Body Opening: 225 mm (8 3/4" Inch) OD - Fabricated High Tensile Steel Base Frame for increased strength and lighter unit weight - High Tensile Fabricated Lever Arms - Adjustable Connecting with Left & Right Hand Threads allowing accurate adjustment of jaw actuation - Cast Jaw Assemblies to suit most standard drill rod sizes - Light weight casting approx. 16 kg per jaw - Easily replaceable Gripper Inserts for NQ & HQ Jaw Sizes - RC Slips Table, Holders and Inserts to suit 3 1/2", 4" & 4 1/2" Rod Sizes - Changeable with Industry Standard Rod Clamps Rod Clamp Location: Australia Learn More

Drill Rig Make: Titan Model: 1000 Year: 2009 Engine: Cummins QSC 8.3 & QSB 4.5 Rotation Torque: 7,500 Nm & 1,100 Nm Auger Speed: 0-180 & 0-980 RPM Pullback Force: 15,000 kg - Onboard American Bean Pump - Onboard Cyclone & 75/25 Splitter Truck Make: Volvo Model: FL10 Year: 1990 KM's: 457 Type: 8x4 GVM: 30,000 kg Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Hammer Size: 12" Inch Drill Bit Size: 20" Inch - With SD12 Shank (Unused) Location: Queensland, Australia Learn More

Make: UDR Replaced; - Hydraulic Ram - Tension Rod - L&R Couplings - Clamps have been 100% disassembled, reassembled and greased up - Jaw Holders supplied with the UDR but look unused (Can be purchased separately along with jaws) - Other Footclamp has Jaw Holders but look unused Footclamp Location: Malaysia Learn More

Make: Gardner Denver Model: 8x5 - Hydraulic Driven Trailer Mounted Mud Pump Location: New South Wales, Australia Learn More

Make: Hydco Model: 1000H Year: 2008 Hours: 4,304 Engine: Cummins 6CTA Onboard Air Compressor: Sullair 1,150 CFM / 350 PSI & 900 CFM / 500 PSI Compressor Hours: 819 Compressor Engine: Caterpillar CAT C15 - Setup for mainly RC however has the diamond capabilities & equipment - Rig has recently been completing RC holes to depths of 425 m coupled with the Aux Compressor Kit giving 2,400 CFM / 1,000 PSI Diamond Drilling Capacity; HQ: 1,000 m NQ: 1,500 m PQ: 600 m Features; - Harlsan Auto Blow Up and Blowdown - KL Rod Handler - Hydraulic Breakouts - Hydraulic Spanners - Safety Cage with Interlock - Quick Access Mountable Stuffing Box Assembly - Fire Suppression - Dust Suppression - FMC Bean Pump for Diamond Drilling - FMC Dual Pump for Water Injection - Hydraulic Foot Clamps - Diamond Drilling Safety Cage - Diamond Drilling Platform - Storage Area with Safety Rails and Access Ladders - Refurbished Cyclone - New Cone Splitter - New Track Chains and Rollers - 400x Metres of 4.5" Inch Remet Rods - Airdrill 670 Hammers & Bits - Other specific RC Gear Track Mounted Drill Rig Location: Western Australia Learn More

Make: Keypower Model: 6V92TA1400 Max Inlet Pressure: 2,413 kPa / 350 PSI Max. Delivery: 660 l/sec / 1,400 CFM Max. Discharge Pressure: 5,171 / 850 PSI Compression Ratio: 2:1 (Nominal) / 3:1 (Maximum) Bore: 57 mm Stroke: 127 mm Max. Operating Angle: 15 degrees Engine: Detroit 6V92TA Diesel *Not Actual Photo of Unit* Skid Mounted Booster Location: New South Wales, Australia Learn More

Make: Cubex Model: QXR 920 Year: 2004 (Rebuild 2019) Hours: 16,896 Engine: Caterpillar CAT C15 Rotary Head: Cubex @ 6,230 hours (Rebuilt May 2019) Rotation Torque: 5,730 Nm Rotation Speed: 0-80 RPM Variable Jaw Rotation: 15 degrees Clamping Force: 288 kN Carousel Capacity: 6 Rods Max. Rod Size: 5" Inch Min. Rod Size: 3.25 " Inch Rod Length: 6 m / 20 ft Onboard Air Compressor: Sullair + Spares Included Track Mounted Surface Drill Rig Location: Western Australia Learn More

Make: FMC Model: L1122 Stroke Length: 2.75" Inch Piston Diameter: 2.75" Inch Frame Load Rating: 6,000 lbs Internal Gear Ratio: 3.6:1 Intermittent Duty Speed Rating: 1,275 RPM Continuous Duty Speed Rating: 900 RPM Standard Suction Size: 2.50" Inch NPT Standard Discharge Size: 1.25" Inch NPT Number of Pistons: 3 Horizontal Triplex Piston Pump Location: New South Wales, Australia Learn More