Search results for: 'pod up camera for state newag me'

2006 Caterpillar CAT C15 Skid Mounted Engine ($59,000 ex GST) (sale-ehub4016)

For Sale

$59,000.00

Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More

Machine hours	1,400	KILOMETERS	N/A
YEAR	2006	BRAND	Caterpillar CAT
LOCATION	Queensland, Australia	MODEL	C15

Add to Wish List Add to Compare

2007 Drill Rig Mounted on 2007 Isuzu FTS 750 4x4 Table Top Truck ($145,000 ex GST) (sale-ehub4003)

For Sale

$145,000.00

Rig Year: 2007 Hours: 3,000 Engine: Caterpillar (85 HP) Stroke: 3,300 mm - 2 Speed Head Rotation Torque: 2,500/450 Nm Rotation Speed: 140/750 RPM Pullback: 7,000 kg Pull Down: 4,000 kg - Set up for Geotechnical Drilling with Auto SPT - 1x Main Winch - 2x Wireline Winch - Mono Pump - Four Jack Legs - Drilling Rods, Alloy Mud Tanks, Accessories for 50 m (All in Good Condition) Truck Make: Isuzu Model: FTS 750 Year: 2007 KM's: 55,000 Type: 4x4 Table Top Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Machine hours	3,000	KILOMETERS	55,000
YEAR	2007	BRAND	N/A
LOCATION	Queensland, Australia	MODEL	N/A

Add to Wish List Add to Compare

TT300 Trailerised Drill Rig + Volvo FH12 460 Truck with Atlas Copco XRV1200 Air Compressor & More Package (POA) (sale-ehub3999)

For Sale

$0.00

Rig Model: TT300 Hours: 18 Engine: Deutz F6L912 / 66 kW Rated Depth Capacity: 300 m Feed Cylinder: 100 mm Barrel / 70 mm Shaft / 4 m Stroke Outrigger (Jacks): 4x Boxed Outriggers with 800 m Stroke Foam Pump: 21 Litre per min / 35 bar Foam/Water Tank: 120 Litre Axles: 2x 5 Tonne Air Braked Axles Tower: Direct on Cylinder / Triangle Shape Winch: 1 Tonne Push Down Force: 5,000 kgf @ 175 bar Pull Up Force: 13,000 kgf @ 175 bar Tilt Cylinders: 2x 80 Barrel 50 Shaft Breakout: 300 mm Stroke Cylinder Hydraulic Oil Tank Capacity: 330 Litres - Hydraulic Oil Cooler - Extended Tower to accommodate 4 m Stroke Cylinder - Spanners Included: 1x Breakout / 2x Keeper / 3x Hammer Modifications; - Hydraulically Tilt Rotary Head - Rotary changed to geared Rotary Head with Hollow Spindle (8,000 Nm Torque) - Including 2x Eaton Hydraulic Motors - Side Shift (on rotary head – opens up the tower for longer casing, etc.) Support Truck Make: Volvo Model: FH12 460 KM’s: 1,040,378 Type: 8x4 Air Compressor Make: Atlas Copco Model: XRV1200 Year: 2020 Hours: 122 Engine: Cummins Pressure: 22.7 bar / 330 PSI Engine/Motor Speed: 1,900 RPM Engine/Motor Power: 325 kW / 430 HP 1,200 CFM / 330 PSI - Included Drill Bits, Rods and Drilling Equipment Trailerised Drill Rig Support Truck Air Compressor Package Location: New Zealand Learn More

Machine hours	18	KILOMETERS	1,040,378
YEAR	2020	BRAND	N/A
LOCATION	New Zealand	MODEL	TT300

Add to Wish List Add to Compare

2022 Rebuilt SPM Weir TWS2250 Skid Mounted Jack Up Frac Mud Pump (FOR HIRE/RENT - POA) (hire-ehub3982)

For Sale

$0.00

Make: SPM Weir Model: TWS2250 Year: 2022 (Reman Rebuild) Hours: Approx. 7,000 Engine: Caterpillar CAT C32 (Rated @ 1,350 HP) Transmission: Allison 8000 Series Auto (DP8962R) Dimensions; Length: 9,135 mm (Overall) Width: 2,505 mm Height: 2,615 mm (On Ground) Height: 4,280 mm (Raised) Weight: 20,000 kg - When raised has enough height for a trailer of 1,500 mm to drive underneath Skid Mounted Jack Up Frac Mud Pump Location: Queensland, Australia Learn More

Machine hours	Approx. 7,000	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	Queensland, Australia	MODEL	SPM Weir TWS2250

Add to Wish List Add to Compare

2022 Rebuilt SPM Weir TWS2250 Skid Mounted Jack Up Frac Mud Pump (POA) (sale-ehub3982)

For Sale

$0.00

Make: SPM Weir Model: TWS2250 Year: 2022 (Reman Rebuild) Hours: Approx. 7,000 Engine: Caterpillar CAT C32 (Rated @ 1,350 HP) Transmission: Allison 8000 Series Auto (DP8962R) Dimensions; Length: 9,135 mm (Overall) Width: 2,505 mm Height: 2,615 mm (On Ground) Height: 4,280 mm (Raised) Weight: 20,000 kg - When raised has enough height for a trailer of 1,500 mm to drive underneath Skid Mounted Jack Up Frac Mud Pump Location: Queensland, Australia Learn More

Machine hours	Approx. 7,000	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	Queensland, Australia	MODEL	SPM Weir TWS2250

Add to Wish List Add to Compare

2016 Safe-T BHA STS R1 Skid Mounted Jack Up Drill Rod Sloop ($120,000 ex GST) (sale-ehub3973)

For Sale

$120,000.00

Make: Safe-T Model: BHA STS R1 Year: 2016 - Surplus to requirements Skid Mounted Jack Up Drill Rod Sloop Location: Tasmania, Australia Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	2016	BRAND	N/A
LOCATION	Tasmania, Australia	MODEL	Safe-T BHA STS R1

Add to Wish List Add to Compare

Schramm T685 Drill Rig Mounted on 2008 MAN TGS 41.480 8x8 Truck (POA) (sale-ehub3967)

For Sale

$0.00

Drill Rig Make: Schramm Model: T685W Year: 2007 Rig Serial Number: J124-B103 Engine: Cummins QSK19 (Hours: 500 - Brand New) Pullback Rating (Hoist Capacity): 33,884 kg Compressor: 2022 (Rebuild) Sullair DC 1,350 CFM / 500 PSI with Caterpillar C18 Compressor Hours: 3,200 (Shown) Compressor Serial Number: 200803290001 Triplex Pump: Bean 535 Pump Table Opening: 20" Inch Dual Breakouts: Metzke Hydraulic Breakout Tong Clutch: Direct Drive Set Up Rotation Head: Airdrill - Fire Suppression - Fold Down Walkways - Guarding (Spin cage with inter lock) - KL Road Loader (Hydraulic fixed) - 685WS Mast Truck Make: MAN Model: TGS 41.480 Year: 2008 KM's: 70,000 Transmission: Automatic Type: 8x8 - Mine Spec Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Machine hours	3,200 (Compressor)	KILOMETERS	70,000
YEAR	2008	BRAND	Schramm
LOCATION	Queensland, Australia	MODEL	T685

Add to Wish List Add to Compare

Hydramaster 2000 Cable Tool Drill Rig Mounted on 1998 International Acco 4x2 Truck & Tri Axle Trailer ($99,000 ex GST) (sale-ehub3957)

For Sale

$99,000.00

Rig Make: Hydramaster Model: 2000 - Fully Tooled & Spares - Recently painted Truck Make: International Model: Acco Year: 1998 KM's: 506,309 Type: 4x2 Engine: Cummins 300 HP Gearbox: 9 Speed Tri Axle Trailer - Near New - Set up for cable tool equipment Condition: Good Truck Mounted Cable Tool Drill Rig Tri Axle Trailer Location: Queensland, Australia Learn More

Machine hours	N/A	KILOMETERS	506,309
YEAR	1998	BRAND	Hydramaster
LOCATION	Queensland, Australia	MODEL	2000

Add to Wish List Add to Compare

Schramm 685 Track Mounted Drill Rig with Onboard Air Compressor ($1,200,000 ex GST) (sale-ehub3582)

For Sale

$1,200,000.00

Rig Make: Schramm Model: 685 Year: 1996 Hours: 2,500 (Since Rebuild) Engine: Cummins K19 Accessories; - FOPS - Rod Rack - 4x Levelling Jacks - In Mast Make/Break Rod Break Out System - Rotating Cyclone Set Up on Metz Manipulator - Airdrill Maker Breaker - Air Spanner - KL Rod Handler Set to 4.5" Inch Pipe - Dual RC Swivel and Auto Blow Down - ROPS Air-Conditioned Drillers Cabin - Complete Re-Hose 11/25 - Fire Suppression Air Compressor Make: Sullair 1,150 CFM / 500 PSI Water Capacity: Approx. 500 Litres Dimensions; Height: 4.6 m Width: 4.0 m Track Mounted Drill Rig Location: Queensland, Australia Learn More

Machine hours	2,500	KILOMETERS	N/A
YEAR	1996	BRAND	Schramm
LOCATION	Queensland, Australia	MODEL	685

Add to Wish List Add to Compare

Exploration Drill Masters EDM MKII Track/Jack Up Rod Sloop Mounted Rod Feeder (EOI) (sale-ehub3931)

For Sale

$0.00

Make: Exploration Drill Masters EDM Model: MKII Hours: 539 Engine: Hatz 1D90V Max. Load Capacity: 15,000 kg Hydraulics: Rexroth 28CC Piston Pump - Capacity for 1,900 m NQ Drill Pipe in 6 m Lengths - 270 Degree Range of Movement - 2.1 m Arm Displacement - 4.770 m Roller Travel Roller Tramming Speed: 0.79 m/s Track Base Make: Sejin Model: 2P254075 Max. Speed: 0.6 km/h - 2 Speed Jack Up Base - 4 Extending Jack Legs - 1.8 m Jack Up Height Dimensions; Overall Platform Length: 8,460 mm Overall Platform Width: 2,500 mm Overall Height: 2,470 mm Empty Weight: 13,000 kg Clearance When Jacked Up: 1,650 mm Track Mounted Jack Up Rod Sloop Rod Feeder Location: Western Australia Learn More

Machine hours	539	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	Western Australia	MODEL	EDM MKII

Add to Wish List Add to Compare

Mud Puppy MP-255-2SC Mud Recycler Pump Mounted on Hydraulic Jack Up Rod Sloop (FOR HIRE/RENT - POA) (hire-ehub3349)

For Hire

Make: Mud Puppy Model: MP-255-2SC - Mounted on Hydraulic Jack Up Rod Sloop Mud Recycler Pump Location: New South Wales, Australia Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	N/A	BRAND	Mud Puppy
LOCATION	New South Wales, Australia	MODEL	MP-255-2SC

Add to Wish List Add to Compare

2005 Epiroc DM-L Track Mounted Rotary Drill Rig (POA) (sale-ehub3867)

For Sale

$0.00

Make: Epiroc Model: DM-L Year: 2005 Hours: 8,453 Engine: Cummins QSX15 Tier 3 - 33.5" Inch Triple Grouser Tracks - 30' Foot Tower Carousel - Can be set up for 5.5" Inch or 6.25" Inch Rods - 4 or 5 Pieces Air End Track Mounted Rotary Drill Rig Location: United States of America Learn More

Machine hours	8,453	KILOMETERS	N/A
YEAR	2005	BRAND	Epiroc
LOCATION	United States of America	MODEL	DM-L

Add to Wish List Add to Compare

2008 Caterpillar CAT 16M Motor Grader (POA) (sale-ehub3868)

For Sale

$0.00

Make: Caterpillar Model: 16M Year: 2008 Hours: 37,752 (Frame) / 5,834 (After Overhaul) Engine: Caterpillar CAT C13 - Complete Overhaul in 2022 Motor Grader Location: United States of America Learn More

Machine hours	37,752	KILOMETERS	N/A
YEAR	2008	BRAND	Caterpillar CAT
LOCATION	United States of America	MODEL	16M

Add to Wish List Add to Compare

UDR1500 Jack Up Drill Rig Mounted on Trailer (POA) (sale-ehub3827)

For Sale

$0.00

Drill Rig Make: UDR Model: 1500 Year: 2011 (Rebuilt) Hours: 3,517 Trailer Make: Hold Bros Year: 2013 ATM: 38 Tonne Jack Up Trailer Mounted Drill Rig Location: New South Wales, Australia Learn More

Machine hours	3,517	KILOMETERS	N/A
YEAR	2013	BRAND	UDR
LOCATION	New South Wales, Australia	MODEL	1500

Add to Wish List Add to Compare

Gardner Denver PAH Mud Pump Mounted on Hydraulic Jack Up (POA) (sale-ehub3814)

For Sale

$0.00

Make: Gardner Denver Model: PAH Hours: 72 Hydraulic Jack Up Mud Pump Location: Queensland, Australia Learn More

Machine hours	72	KILOMETERS	N/A
YEAR	N/A	BRAND	Gardner Denver
LOCATION	Queensland, Australia	MODEL	PAH

Add to Wish List Add to Compare

Gardner Denver PAH Mud Pump Mounted on Hydraulic Jack Up (POA) (sale-ehub3813)

For Sale

$0.00

Make: Gardner Denver Model: PAH Hours: 20 Hydraulic Jack Up Mud Pump Location: Queensland, Australia Learn More

Machine hours	20	KILOMETERS	N/A
YEAR	N/A	BRAND	Gardner Denver
LOCATION	Queensland, Australia	MODEL	PAH

Add to Wish List Add to Compare

Edson Versadrill 300 Drill Rig Mounted on Toyota Landcruiser Ute ($125,000 ex GST) (sale-ehub3781)

For Sale

$125,000.00

Rig Make: Edson Model: Versadrill 300 Year: 1996 Engine: Hatze - 6x6 Multidrive Technology - Rotation head MR260 Rotation hollow spindle, single speed, dial in, rotation head around 120 rpm - Winching gear on back of mast for hollow augering - Can do diamond drilling if you were to change the hydraulic motor - Dump Mast - Near New Hydraulic Pump - 4x Leveling Jacks - Currently doing 80mtr holes at 4.5” - Client used to aircore with it, but currently set up doing mud - Used to do a lot of Geotech work, 6” hollow augering - Southern Cross Mud pump on the side - 3.2 mtr Stroke - 3 mtr Rods - Extension arm to run 6mtr casing into the ground Ute Make: Toyota Model: Landcruiser Year: 1990 KM's: 107,000 Ute Mounted Drill Rig Location: Western Australia Learn More

Machine hours	N/A	KILOMETERS	107,000
YEAR	1996	BRAND	Edson
LOCATION	Western Australia	MODEL	Versadrill 300

Add to Wish List Add to Compare

2012 GN Solids Control GN1000 Skid Mounted Mud Cleaning Unit ($99,000 ex GST) (sale-ehub3753)

For Sale

$99,000.00

Make: GN Solids Control Model: GN1000 Year: 2012 Capacity: 18 m3 - 2x Scalping Shakers - 1x Underflow Shaker with 2x De-Sander Cones (Need Replacing) - 16x De-Silter Cones - Good Quality Australian Approved Electricals in Control Cabinets - Mixing Hopper at Suction Tank End - Steps and Fold Up Walkways & Handrails Condition: Good Dimension: 11,500 x 2,300 x 1,800 mm Weight: 10,350 kg Skid Mounted Mud Cleaning Unit Location: Victoria, Australia Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	2012	BRAND	GN Solids Control
LOCATION	Victoria, Australia	MODEL	GN1000

Add to Wish List Add to Compare

2013 CE100 Diamond Core Track Mounted Drill Rig (POA) (sale-ehub3734)

For Sale

$0.00

Make / Model: CE100 Year: 2013 (Rebuilt completed in 2022) Hours: 551 - Fully Re-Engineered - NDT Testing Completed - CT14 Hydraulic Operating System - NQ, HQ, PQ Drilling Capabilities - Up to date Safety Stop Systems - Engineered and compliant hand rail and walkway system and access ladders - Full lighting for N/S operations - Certified FOPS on driller platform - Running new Danfos Primary Hydraulic Pump at >3500 PSI direct from John Deere 127 HP - 165 HP engine - 5.7 Tonne Main Winch with certified 16mm Winch Rope - A new AMC Main Water Pump <1000 PSI with a PRV Valve Set @750 PSI - New Stryker 45ltr Certified Fire Suppression system installed - A UDR Rod Spinner has been engineered into mast structure for hands free operation of tripping rods - A hydraulic operated Breakout Spanner allows for breakout of rod joins or subs - Tungsten inserts interchangeable on Breakout Spanner - UDR Foot Clamp assembly added for ease of maintenance and clamping of rod string Diamond Core Track Mounted Drill Rig Location: Western Australia Learn More

Machine hours	551	KILOMETERS	N/A
YEAR	2013	BRAND	CE100
LOCATION	Western Australia	MODEL	CE100

Add to Wish List Add to Compare

150N Track Mounted Multi Purpose Drill Rig (New Build - POA) (sale-ehub3725)

For Sale

$0.00

Model: 150N Engine: John Deere / FPT Iveco / Kirloskar / Deutz Pull Up Force: 5,000 kg Pull Down Force: 3,750 kg Tool Winch Hoisting Capacity: 2,500 kg (Bare Drum) Wireline Winch Hoisting Capacity: 500 kg (Bare Drum) Diamond Core Drilling Capacity; NQ Size: 150 m HQ Size: 90 m PQ Size: 60 m Water Pump; Max Flow: 120 LPM Max Pressure: 30 bar Type: Triplex Piston Pump Track Mounted Multi Purpose Drill Rig Location: United Arab Emirates Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	United Arab Emirates	MODEL	MD150N

Add to Wish List Add to Compare

Search results for: 'pod up camera for state newag me'

AUSTRALIA WIDE SERVICE

REQUIRE ASSISTANCE - HAVE A QUESTION?

EQUIPMENT FOR HIRE OR FOR SALE