Search results for: 'wheel to load for rent for state'

Make: Exploration Drill Masters EDM Model: MKI Year: 2020 Hours: 502 Engine: Hatz 1B20V - All Haul and Drive Subs Included (HRQ, NRQ) Capacity; Max Load Capacity: 15,000 kg - Capacity for 2,000 Nm NQ Drill Pipe in 6 Metre Lengths Track Base; Make: Strickland Model: DT224E - Positioning Tracks Dimensions; Overall Platform Width: 2,460 mm Overall Platform Length: 7,466 mm Overall Height: 2,765 mm Empty Weight: 10,500 kg Clearance When Jacked Up: 1,650 mm Track Mounted Jack Up Rod Sloop Rod Feeder Location: Western Australia Learn More

Make: Komatsu Model: WA 900-8 Year: 2020 Hours: 14,212 Wheel Loader Location: United States of America Learn More

Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More

Make / Model: Ubuilt Cassady CTU Carrier & Booster OD Year: 2010 Hours: 310 Engine: John Deere ATM: 61,500 kg Trailer Make: Ensign Model: C.T. 1000 Year: 2005 Tyre Size: 275/70R22.5 Rim Size: 8.25x22.5 Axle Group Load Carrying Capacity: 37,500 kg - Handrail and Stair Upgrade by Obadare CTU Coil Tubing Unit Carrier Mounted Location: Queensland, Australia Learn More

Rig Model: ZJ50D/3150 Year: 2012 Mast Model: JJ315/45-K6 Substructure Model: DZ3159-S Drawworks Model: JC50D Power: 1,500 HP Rotary Table Model: ZP-375 Full Opening: 37.5” Inch Rotary Speed: 300 RPM Mud Pump Power: 1,600 HP Stroke: 120 RPM Working Pressure: 5,000 PSI Quantity: 2x Mud Tank Shaker Tank: 25 CuM Intermediate Tank: 40 CuM Suction and Mixing Tank: 20 CuM Solids Control - 3x Shale Shaker - 1x Mud Cleaner - 1x Centrifuge Drill Rig Location: Japan Learn More

Make: SPM Weir Model: TWS2250 Year: 2022 (Reman Rebuild) Hours: Approx. 7,000 Engine: Caterpillar CAT C32 (Rated @ 1,350 HP) Transmission: Allison 8000 Series Auto (DP8962R) Dimensions; Length: 9,135 mm (Overall) Width: 2,505 mm Height: 2,615 mm (On Ground) Height: 4,280 mm (Raised) Weight: 20,000 kg - When raised has enough height for a trailer of 1,500 mm to drive underneath Skid Mounted Jack Up Frac Mud Pump Location: Queensland, Australia Learn More

Make: IMS Model: Bulwark 200 Year: 2010 Max Operating Wind Velocity: 12.5 m/sec Max Rated Hook Load: 196kN Height: 16 Metres 20 Tonne Work-Over Drill Rig Location: Queensland, Australia Learn More

Make: Exploration Drill Masters EDM Model: MKII Hours: 539 Engine: Hatz 1D90V Max. Load Capacity: 15,000 kg Hydraulics: Rexroth 28CC Piston Pump - Capacity for 1,900 m NQ Drill Pipe in 6 m Lengths - 270 Degree Range of Movement - 2.1 m Arm Displacement - 4.770 m Roller Travel Roller Tramming Speed: 0.79 m/s Track Base Make: Sejin Model: 2P254075 Max. Speed: 0.6 km/h - 2 Speed Jack Up Base - 4 Extending Jack Legs - 1.8 m Jack Up Height Dimensions; Overall Platform Length: 8,460 mm Overall Platform Width: 2,500 mm Overall Height: 2,470 mm Empty Weight: 13,000 kg Clearance When Jacked Up: 1,650 mm Track Mounted Jack Up Rod Sloop Rod Feeder Location: Western Australia Learn More

Make: Mud Puppy Model: MP-255-2SC - Mounted on Hydraulic Jack Up Rod Sloop Mud Recycler Pump Location: New South Wales, Australia Learn More

Make: Caterpillar Model: 992K Year: 2012 Hours: 20,199 - No EPA - No CE Wheel Loader Location: Chile Learn More

Make: Sandvik Model: DD420 Tyres: Bridgestone 12.00R20 - Typical Wear & Tear - Surface Rust on Rims - Was Removed from Running Machine Condition: Good Quantity: 4 Wheel Set Location: Western Australia Learn More

Power (kW): 9-13, 30-50, 58-90, 150 Min. Flow (m3/hr): 1.5-6, 4.8-9, 8-15, 15-24 Throw (m): 30-50, 70-100, 120-150, 250 Oscillation (Deg): 0-360 Throw Angle (Deg): -5 to +45 - Stockpiles - Mine Blast Dust - Conveyor Discharge Chutes - Dust Hoppers - Crusher Machinery - Loading and Unloading Trucks - General Pollution - Airborne Dust - Construction Sites - Odor Control and Management Dust Suppression Location: Queensland, Australia Learn More

Model: OIE187 Cannon Fan: 425,000 m3/hr / Dual Fiber Glass PAG Impeller Discharge Hose: 1.5" Inch & 500 PSI High Pressure Pump: 7-8 Bars Discharge Fan Power: 130 kW Pump Power: 55 kW Pump Flow: 150 m3/hr Evaporation Rate: 24.98 lps @ 60% Daily Operating Time: 10 Hours + - SS Ring with Nozzles - Spiral Nozzle SS316 - Fan Safeguard Mesh - Control Panel Generator Make: Shanghai Stamford Brushless Engine: Dongfeng Cummins Control System: HGM6110 Large Screen Radiator: Engine Standard Matching Fuel Tank: 1,000 Litres Battery: 2x Camel 12V Weight: 6,000 kg approx. - Waste Water Handling - Dewatering Process - Tailing Dams - Water Production - Rainstorm Water Clearance Water Evaporator Location: Queensland, Australia Learn More

Power (kW): 9-13, 30-50, 58-90, 150 Min. Flow (m3/hr): 1.5-6, 4.8-9, 8-15, 15-24 Throw (m): 30-50, 70-100, 120-150, 250 Oscillation (Deg): 0-360 Throw Angle (Deg): -5 to +45 - Stockpiles - Mine Blast Dust - Conveyor Discharge Chutes - Dust Hoppers - Crusher Machinery - Loading and Unloading Trucks - General Pollution - Airborne Dust - Construction Sites - Odor Control and Management Dust Suppression Location: Queensland, Australia Learn More

Make: Epiroc Model: DM-L Year: 2005 Hours: 8,453 Engine: Cummins QSX15 Tier 3 - 33.5" Inch Triple Grouser Tracks - 30' Foot Tower Carousel - Can be set up for 5.5" Inch or 6.25" Inch Rods - 4 or 5 Pieces Air End Track Mounted Rotary Drill Rig Location: United States of America Learn More

Make: Caterpillar Model: 16M Year: 2008 Hours: 37,752 (Frame) / 5,834 (After Overhaul) Engine: Caterpillar CAT C13 - Complete Overhaul in 2022 Motor Grader Location: United States of America Learn More

Rig Make: UDR Model: 650 Hours: 9,202 - Commissioned Mid 2023 - Onboard PTO Driven Air Compressor - New water pump - New fan belts - New radiator core - Recent service with oil & new filters - New rod & piston seals to main feed Ram - New Dump Mast Ram - New rods & seals to mast raise rams - New side shift ram - New break out ram - New rod crane raise ram - New hydraulic valve blocks in control cabinet for main pump & secondary pump controls - New micro control fine feed controller - Replaced majority of gauges with new - New main rotation shaft seals & speedy sleeves - New main rotation torque control cartridge - New hammer oiler pump - New seats & O rings in majority of valve banks Air Compressor - New Air / Oil separator filter - New Oil stop valve - New Castrol Aircoil 68 synthetic oil - New filters - Recently been serviced by Midcoast Compressors Truck Make: MAN Year: 1997 KM's: 200,000 Type: 8x8 Transmission: Recon 18 Speed Gear Box - Kevrek 1500 Hiab Crane with Winch & Umbilical Cord Remote - Radiator back flushed - New Water Pump - New Fan Belts - New brake boosters on every wheel - New four way valve - New valve on brake pedal - Rebuilt Truck Compressor - New air on drivers seat - New air valves on diff locks / cross locks - New clutch, fly wheel & pressure plate - New bearings & seals in Dana drive box - New oil pump on Dana drive box - New universals on tail shafts - New ram on power steering - New tyres all around - All ball joints on truck replaced that were needed, or new rubbers on them - Recently passed Pit Inspection - 7 months Rego as Plant - No need for overhang permits; within length Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Make: Atlas Copco Model: Pit Viper 275 Hours: 19,237 Load Capacity: 75,000 lb Engine: Caterpillar CAT C32 - 4 Rod Carousel approx. 40 ft. - Atlas Copco QAS 45 Diesel Generator Dimensions; Length: 41ft. 6 inch / 63ft. 6 inch (Tower Down) Width: 18ft. 4 inch Height: 67ft. / 22ft 1 inch (Tower Down) Track Mounted Drill Rig Location: Canada Learn More

Includes; - Kitchen - Lunch Room / Work Space Room - Storage Dual-Axle Van Location: Australia Learn More

Includes; - Kitchen - Lunch Room / Work Station Room - Generator - 2x Toilets Tri-Axle Van Location: Australia Learn More