Search results for: 'wheel to lock for receiv for size'

Bit 1 Size: 9" Inch - 380 IR Shank - Welded Legs Condition: Used Price: $880 ex GST Bit 2 Size: 9" Inch - 380 IR Shank Condition: Never Used Price: $1,100 ex GST Bit 3 & 4 Size: 9" Inch - 380 IR Shank Quantity: 2 Condition: Good Price: $1,100 ex GST each Hammer Drill Bit Location: Western Australia Learn More

Size: 7" Inch - PDC Condition: Used Drill Bit Location: Western Australia Learn More

Size: 12 1/4" Inch - TCI - Sealed Bearing Condition: Used Rock Roller Bit Location: Western Australia Learn More

Size: 12 1/4" Inch - Milled Teeth - Sealed Bearing Condition: Good Rock Roller Bit Location: Western Australia Learn More

Rig Make: UDR Model: 650 Hours: 9,202 - Commissioned Mid 2023 - Onboard PTO Driven Air Compressor - New water pump - New fan belts - New radiator core - Recent service with oil & new filters - New rod & piston seals to main feed Ram - New Dump Mast Ram - New rods & seals to mast raise rams - New side shift ram - New break out ram - New rod crane raise ram - New hydraulic valve blocks in control cabinet for main pump & secondary pump controls - New micro control fine feed controller - Replaced majority of gauges with new - New main rotation shaft seals & speedy sleeves - New main rotation torque control cartridge - New hammer oiler pump - New seats & O rings in majority of valve banks Air Compressor - New Air / Oil separator filter - New Oil stop valve - New Castrol Aircoil 68 synthetic oil - New filters - Recently been serviced by Midcoast Compressors Truck Make: MAN Year: 1997 KM's: 200,000 Type: 8x8 Transmission: Recon 18 Speed Gear Box - Kevrek 1500 Hiab Crane with Winch & Umbilical Cord Remote - Radiator back flushed - New Water Pump - New Fan Belts - New brake boosters on every wheel - New four way valve - New valve on brake pedal - Rebuilt Truck Compressor - New air on drivers seat - New air valves on diff locks / cross locks - New clutch, fly wheel & pressure plate - New bearings & seals in Dana drive box - New oil pump on Dana drive box - New universals on tail shafts - New ram on power steering - New tyres all around - All ball joints on truck replaced that were needed, or new rubbers on them - Recently passed Pit Inspection - 7 months Rego as Plant - No need for overhang permits; within length Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Model: 150N Engine: John Deere / FPT Iveco / Kirloskar / Deutz Pull Up Force: 5,000 kg Pull Down Force: 3,750 kg Tool Winch Hoisting Capacity: 2,500 kg (Bare Drum) Wireline Winch Hoisting Capacity: 500 kg (Bare Drum) Diamond Core Drilling Capacity; NQ Size: 150 m HQ Size: 90 m PQ Size: 60 m Water Pump; Max Flow: 120 LPM Max Pressure: 30 bar Type: Triplex Piston Pump Track Mounted Multi Purpose Drill Rig Location: United Arab Emirates Learn More

Model: 75N Engine: Kirloskar / Deutz / John Deere Pull Up Force: 2,500 kg Pull Down Force: 2,500 kg Tool Winch Hoisting Capacity: 1,500 kg Diamond Core Drilling Capacity; NQ Size: 75 m HQ Size: 45 m PQ Size: 30 m Mud Rotary; 30 m @ 150 mm Diameter Auger Drilling; 20 m @ 150 mm Diameter 4 m @ 300 mm Diameter Water Pump; Max Flow: 85 LPM / 140 LPM Max Pressure: 30 bar / 18 bar Type: Triplex Piston Pump / Progressive Cavity Pump Compact Geotechnical Drill Rig Location: United Arab Emirates Learn More

Rig Make: Boart Longyear Model: LF90 Year: 2008 Hours: 14,154 - Fitted with KWL 400 Head as Top Drive - Masts are locked at 6 Metre Rod Pull - Has been drilling in Iron Ore Truck Make: Tatra Year: 2008 KM's: 37,735 Type: 8x8 Truck Mounted Drill Rig Location: Western Australia Learn More

Make: Mole Pioneer Model: P400S 450HQ Hours: 2,940 Engine: Perkins 119 kW Diesel - Onboard W1122 Bean Pump Rotation Head Model: KL400 Top Drive Stroke: 1,200 mm Drilling Angle: 90 degrees vertical to 45 degrees horizontal Drilling Depth Capacity B Size: 900 metres N Size: 700 metres H Size: 450 metres P Size: 275 metres Truck Make: Ford Model: Cargo Series KM's: 25,372 Year: 1985 Type: 6x4 Condition: Good *For more information, please contact us* Mole Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Model: WP500 Engine: Cummins QSB 4.5 @ 119 kW (160 HP) Fuel Tank Capacity: 200 Litres Estimated Weight: 2,890 kg (excluding trailer) - Base Frame to support engine, pumps, hydraulics and fuel tanks, etc. - Paint, Two Pack Evolution Yellow Hydraulics; - Pump Group Bosch Rexroth - A11VO95/A10VO85/16 - Maximum Circuit Pressure: 250 Bar - Hydraulic Oil Capacity: 400 Litres - Return Filter: 10 Micron - Hydraulic Oil Cooler and Fan Water Pumps; Make: FMC Model: L11-18SC Water Flow Range: 0-530 lpm (140 US/GPM) Maximum Water Pressure: 69 Bar (1,000 PSI) - Adjustable Water Pressure Relief Valve - Water Discharge Pressure Gauge - Surge Chambers on suction & discharge - Discharge Pulsation Dampener - Volvo fixed displacement Piston Drive Motors - Flex Drive Couplings - 2" Inch Water Delivery Hose x 10 metres long Control Panel; - Remote Pilot Hydraulic Control to attach at Rig Control Panel - Selectable Pump 1, 2 or both - Adjustable Friction Lock Control - Selectable Fine Speed Control on Pump 1 - Interconnecting Hoses 10 metres long Skid Mounted Mud Pump Location: Australia Learn More

Body Opening: 225 mm (8 3/4" Inch) OD - Fabricated High Tensile Steel Base Frame for increased strength and lighter unit weight - High Tensile Fabricated Lever Arms - Adjustable Connecting with Left & Right Hand Threads allowing accurate adjustment of jaw actuation - Cast Jaw Assemblies to suit most standard drill rod sizes - Light weight casting approx. 16 kg per jaw - Easily replaceable Gripper Inserts for NQ & HQ Jaw Sizes - RC Slips Table, Holders and Inserts to suit 3 1/2", 4" & 4 1/2" Rod Sizes - Changeable with Industry Standard Rod Clamps Rod Clamp Location: Australia Learn More

Model: 1750 Scout Engine: Perkins Diesel Torque: 2,500 Nm at 205 bar and 110 RPM Stroke: 1.75 m Pull-Out / Pull-Down: 1,100 kg Capacity (Guide Only): NQ - 60 m / 4" Inch Open Hole - 30 m / 3 1/2" Inch Auger - 15 m - Custom Toyota 33220 Tray - Direct Dive Auger Head with High Torque Head Motor and Fittings - Fine Feed Control - Auger Drive Sub (1 1/8" Inch Hex) - RHS Mast - Tilt Frame for Vehicle/Trailer Mounting - Hydraulic Tilt - Heavy Duty Pull-Down Chain - Nylon Idler Rollers - Standard Auger Guide - Standard Control Panel - Hydraulic Operation - Rain Hood for Motor & Lockable Cage for Spare Wheel & Motor - Remove Throttle and Stop - Water Filter for Fuel / Water Separation - Light Guard for Augers 500 mm to 1,800 mm - Oil Cooler - Simple Rack for Augers Options for Drill; - Hollow Spindle Head and Tooling for Fluid Drilling - 2 Levelling Jacks for Tray Mount Drills - Tilting Rack for Augers - Alternative Engine Options to suit existing fleet Toyota Landcruiser Upgrade Kit; - Roof Racks for Spare Tyre (31678) - Roof Rack Mounts Pair (31679) - GVM Upgrade Spring Kit @ 4,200 kg (Supply Only - 31680) - Bellows Suspension Kit (Supply Only - 31730) - Storage Box LH Under Deck (33249) - Storage Box RH Under Deck (33248) - Under Deck Water Tanks @ 29 Litres (33137) *Ready for mounting to a Toyota 79 Series Landcruiser Cab Chassis* Drill Rig Location: Australia Learn More

Hammer Size: 12" Inch Drill Bit Size: 20" Inch - With SD12 Shank (Unused) Location: Queensland, Australia Learn More

Make / Model: TL-400 Contains: - Tower - Flashlight - Headlight - Charger - Driver - Battery System D24-100 - USD Output, 5V 2A (2 Dock) for charging Headlight, Flashlight or Mobile Phone - 1-3 Battery Pack (1 Battery 30+ Hours extreme mode) - Height: 64.5 cm - 220 cm - Weight: 12.85 kg - One Man Operation - Self locking and 30 degree + up/down adjustable pole - Run Times > 10 hours (High output, 3 batteries) Application - Drilling - Construction - Maintenance - Events - Mining - Emergency - Infrastructure - Personal Control Board - Power Switch - Brightness - DIM+, DIM- - Battery Level - AC Plug - USB Output Light Brightness Area: 1,100 m2 5 m - 490 lux / 10 m - 120 lux / 20 m - 29 lux / 40 m - 7 lux Battery / AC 100-227V - AC 0-15,000 LM - High 8,000 LM - Medium 5,000 LM - Low 2,500 LM - Extreme 800 LM - Rate Power 28 wh - Rate Voltage 24.5 V - Rate Capacity 40 Ah - Working Temp: -10 to 50 degrees - Working Humidity: -20 to 95% Portable Light Tower Location: Queensland, Australia Learn More

Make: Ferrari Type: 360 Hours: Very Low Engine: Lombardini - 3 Forward and 3 Reverse Gears - Added Depth Control Wheels - Ideal for Professional Market Garden Rotary Hoe Location: Western Australia Learn More

Make: Cubex Model: QXR 920 Year: 2004 (Rebuild 2019) Hours: 16,896 Engine: Caterpillar CAT C15 Rotary Head: Cubex @ 6,230 hours (Rebuilt May 2019) Rotation Torque: 5,730 Nm Rotation Speed: 0-80 RPM Variable Jaw Rotation: 15 degrees Clamping Force: 288 kN Carousel Capacity: 6 Rods Max. Rod Size: 5" Inch Min. Rod Size: 3.25 " Inch Rod Length: 6 m / 20 ft Onboard Air Compressor: Sullair + Spares Included Track Mounted Surface Drill Rig Location: Western Australia Learn More

Make: FMC Model: L1122 Stroke Length: 2.75" Inch Piston Diameter: 2.75" Inch Frame Load Rating: 6,000 lbs Internal Gear Ratio: 3.6:1 Intermittent Duty Speed Rating: 1,275 RPM Continuous Duty Speed Rating: 900 RPM Standard Suction Size: 2.50" Inch NPT Standard Discharge Size: 1.25" Inch NPT Number of Pistons: 3 Horizontal Triplex Piston Pump Location: New South Wales, Australia Learn More

74x Halco Mach 44 4 1/2" Inch Convex Domed Condition: New / Used (Rust) 33x Halco Mach 44 4 1/4" Inch Convex Domed Condition: New / Used (Rust) 1x Halco Mach 44 4 1/2" Inch Concave Domed Condition: New 3x Halco Mach 44 4 1/8" Inch Convex Domed Condition: New 34x Halco Mach 303 3 1/2" Inch Convex Ballistic Condition: New 3x Karbo 4 1/2" Inch Convex Condition: New 4x Karbo 4 1/2" Inch Convex Condition: 3x New / 1x Used Various Size, Shank, Head & Insert Drill Bits Location: Canada Learn More

Make: Custom Model: 600 RRD Motor: 40 HP TEFC Pulling Capacity: 24,000 lbs Lifting Capacity: 24,000 lbs Down Thrust Capacity: 12,500 lbs Rotational Torque: 6,500 ft/lbs Load Sensing Power Limiting Pump: 45 GPM @ 1,700 PSI Load Sensing Diesel Pump: 15 GPM @ 3,500 PSI Fast Feed: 14.79 GPM @ 2,500 PSI Slow Feed: 6.2 GPM @ 2,500 PSI Traction Hydraulic Motor: 14 HP each at 4,000 MASL (Using Diesel Drive) Max. Drilling Air Pressure: 400 PSI Feed Cylinders Combined Bore: 9.8 sq inch Features; - Lubricator - Water Pump - Robust Mine Proven Construction - High Torque Rotation Head - Reversable Heavy Duty Mast - Efficient Electric/Hydraulic Drive - Fully Hydraulic Operation - Compact Size - Fully Variable Rotation Speed (0-24 RPM) Hydraulically Operated Crawlers - Remotely Operated Hydraulic Console for flexibility - Sting Cylinder - Dual Heavy Duty Feed System - 90 Degree Tilt Out Rotation Head - Longitudinal Shift - Side Shift - NEMA 4 - Air Motors for travelling Track Mounted Drill Rig Location: Canada Learn More

Make: Sandvik Model: DR560/80 Hours: Various Max Feed Rate: 1.3 m/s (257 ft/min) Max Hoisting @ 2,100 RPM: 47 kN (10,600 lbf) Max Pulldown @ 2,100 RPM: 47 kN Top Drive Rotation Torque: 5,730 Nm Rotation Speed: 0-80 RPM (Variable) Carousel Standard Capacity: 6 Rods (5 Rods for OD 140 mm (5.5" inch) Max Rod Size: 140 mm / 5.5" inch Min Rod Size: 89 mm / 3.5" inch Rod Length: 6.1 m / 20 ft Min Hammer Size: 102 mm / 4" inch Carousel Hole Depth: 42.6 m / 140 ft Max Hole Size: 216 mm / 8.5" inch Min Hole Size: 115 mm / 4.5" inch + More information can be provided Track Mounted Contour DTH Drill Rig Location: Western Australia Learn More