Search results for: 'dozer size prime head hire cab cjt64 cfm'

Air Compressor Make: Elgi Year: 2023 Hours: 364 - Like New 900 CFM 350 PSI Truck Make: Iveco Year: 2007 KM's: 300,000 Engine: Cummins 285 Turbo Transmission: Alison Automatic - 6.5 Metre Tray - Tow Hitch - Fuel Tank - Water Tank Truck Mounted Air Compressor Package Location: Queensland, Australia Learn More

Make: Elgi Year: 2023 Hours: 364 - Like New 900 CFM 350 PSI Skid Mounted Air Compressor Location: Queensland, Australia Learn More

Make: G&K Model: 850 Engine: Caterpillar CAT 3208 (Rebuilt) Hours: 200 approx. - Replaced Extensive Hydraulic Hoses - Bean Pump on deck - 72 Metres of 4" Inch Waterbore Drill Pipe, comes with Head Tubes and Air Swivel Lots of Spares; - 2x Spare Heads -2x Spare Winches -1x Spare Wireline Drilling Capacity; 12" Inch Hole: Approx. 200 + Metres NQ: 800 Metres HQ: 600 Metres Truck Mounted Waterbore / Diamond Drill Rig Location: Victoria, Australia Learn More

Rig Make: UDR Model: 650 Onboard Compressor: Sullair 1,150 CFM / 350 PSI Air Compressor - Set up for Waterbores, RC and Aircore - Table opens up to allow 14” inch casing or bit - Recent major service of Air End, Separator Filter & New Oil - New Head Slides - New Jib Ram - New Pull Down Ropes - Head Serviced Includes; - Cyclone & Splitter - New Bull Hose - 25x Used 4” Inch RC Rods with Inner Tubes - 2x Head Tubes - Air RC Swivel - Mud Rotary Swivel - Hydraulic Breakout Arm - 4” Inch Airdrill RC Hammer (in Good Condition) & 2x Hammer Tubes - 7x 5” Inch Hammer Bits (Used) - 1x 4” Inch Back Hammer - 1x 8” Inch Aircore Bit - 4” Inch Aircore Bits (2x New & 3x Used) - Blow Up Sub - 1x 4 ½” Inch PDC Bit - 6” Inch Casing Elevator Set - Diverter Box with 20x Rubbers - Stuffing Box - Rod Spanner to suit - Dig Out Sub Rig Truck Make: Volvo Year: 2012 - Twin Steer Option 1 – Water Bore Drilling Equipment (Additional $15,400 ex GST) - 12” Inch Blade Bit (Near New) - 7 7/8” Inch Blade Bit - 8” Inch Tri-Cone Med Formation (Near New) - 6” Inch Shreps Hammer with 6” Inch & 8” Inch Bits (New) - Adaptor Subs to suit - Rod Spanners to suit - Casing Elevators Option 2 – RC Rods (Additional $55,000 ex GST) - 180 Metres of RC 4” Inch Remet Rod String (New) Option 3 – Hooklift Truck + Bins ($55,000 ex GST) Truck Make: Isuzu Year: 2000 - Hooklift Truck Bins; 1st Bin: 6x5 Gardner Denver Mud Pump with Perkins Engine 2nd Bin: To carry PVC and Gravel 3rd Bin: To carry Water Suttles Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Make: Komatsu Model: D155AX-7 Year: 2014 Hours: 3,683 Engine: Komatsu SAA6D140E-6 @ 360 HP Horsepower: 360 HP Automatic Transmission: Komatsu TORQFLOW Max. Speed Forward: 11.6 km/h Max. Speed Reverse: 14 km/h Hydraulic System: CLSS Tare: 39,700 kg Shoe Width: 610 mm Blade Width: 4,060 mm - SS Ripper - Unique Torque Converter with Auto Lock-Up - EU Stage IIIB - Selectable Working Modes - Adjustable Eco-Gauge and Idle Caution Track Mounted Crawler Dozer Location: New Zealand Learn More

Make: Sandvik Drilltech Model: D75KS Engine: Caterpillar CAT 3412 - 2 x Rotation Heads (One still on mast) - Complete Mast (New Generation) - Air End - Air Receiver - Newly Rebuilt Drifter Track Mounted Rotary Blast Hole Drill Rig Location: Northern Territory, Australia Learn More

Make: Caterpillar Model: 3406E 550 HP Engine Number: 5EK70781 Arrangement Number: 1285403 - Removed from a 1991 Kenworth T900 Truck (Done approx. 25,000 km - Diagnosed radiator was too small in the truck for a 3x trailer road train assembly) - Number 1 Cylinder has nipped up and an insurance claim was carried out by a mechanic and an exchange of a C15 fitted to truck, engine still turns over - New Cylinder Head, Injectors, and Rocker Gear with New Top and Bottom Engine Harnesses - New Exhaust Manifold, Turbo, Water Pump, Oil Cooler & Oil Squirters - New Pistons, Liners & Rods are all IPD Parts Engine Location: Northern Territory, Australia Learn More

Drill Rig Make: Warman Model: 1000 - No Head Included - Requires Refurbishment Truck Make: Volvo Model: FL10 Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Make: Ozcon Size: 12-3/4" Inch Length: 6 Metre Quantity: 7 Casing Location: Queensland, Australia Learn More

Size: 5-9/16" Inch Length: 6 Metre Quantity: 25 Casing Location: Queensland, Australia Learn More

Make: UDR/Sandvik Model: 1200/DE880 - Dropped Selector Rotation Head Location: Queensland, Australia Learn More

Make: Ford Model: Ranger Year: 2016 KM's: 198,349 GVM: 3,200 kg Dual Cab Ute Location: Queensland, Australia Learn More

Make: UDR/Sandvik Model: 1200/DE880 - In Bits - Refurb Rotation Head Location: Queensland, Australia Learn More

Rig Make: Boart Longyear Model: LS600 / BL600C Hours: 5,905 (New Engine Fitted in 2023 – Only a few hundred hours since) - 2x Boart Longyear BLY150 Reconditioned Sonic Heads (Ready to go and can be included) - Head Spares and some other big spares Support Unit Make: Morooka Hours: 423 Year: 2011 Track Mounted Multipurpose Sonic Drill Rig Support Unit Location: Scotland Learn More

Make: UDR Model: KL1500 Push Down: 15,080 kg Pull Back: 19,000 kg Compressor: Atlas Copco 1,100 CFM / 400 PSI Rod Handler: UDR KL Pipe Handler - Maker Breaker Jaws - No Rods Included - No Cyclone Specifications: Width: 2.7m Length: 13.8m Height (Mast Down): 4.4m Height (Mast Up): 14m Weight: 39,850kg Carrier Mounted Drill Rig Location: Queensland, Australia Learn More

Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More

Make / Model: Ubuilt Cassady CTU Carrier & Booster OD Year: 2010 Hours: 310 Engine: John Deere ATM: 61,500 kg Trailer Make: Ensign Model: C.T. 1000 Year: 2005 Tyre Size: 275/70R22.5 Rim Size: 8.25x22.5 Axle Group Load Carrying Capacity: 37,500 kg - Handrail and Stair Upgrade by Obadare CTU Coil Tubing Unit Carrier Mounted Location: Queensland, Australia Learn More

Rig Year: 2007 Hours: 3,000 Engine: Caterpillar (85 HP) Stroke: 3,300 mm - 2 Speed Head Rotation Torque: 2,500/450 Nm Rotation Speed: 140/750 RPM Pullback: 7,000 kg Pull Down: 4,000 kg - Set up for Geotechnical Drilling with Auto SPT - 1x Main Winch - 2x Wireline Winch - Mono Pump - Four Jack Legs - Drilling Rods, Alloy Mud Tanks, Accessories for 50 m (All in Good Condition) Truck Make: Isuzu Model: FTS 750 Year: 2007 KM's: 55,000 Type: 4x4 Table Top Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Rig Model: TT300 Hours: 18 Engine: Deutz F6L912 / 66 kW Rated Depth Capacity: 300 m Feed Cylinder: 100 mm Barrel / 70 mm Shaft / 4 m Stroke Outrigger (Jacks): 4x Boxed Outriggers with 800 m Stroke Foam Pump: 21 Litre per min / 35 bar Foam/Water Tank: 120 Litre Axles: 2x 5 Tonne Air Braked Axles Tower: Direct on Cylinder / Triangle Shape Winch: 1 Tonne Push Down Force: 5,000 kgf @ 175 bar Pull Up Force: 13,000 kgf @ 175 bar Tilt Cylinders: 2x 80 Barrel 50 Shaft Breakout: 300 mm Stroke Cylinder Hydraulic Oil Tank Capacity: 330 Litres - Hydraulic Oil Cooler - Extended Tower to accommodate 4 m Stroke Cylinder - Spanners Included: 1x Breakout / 2x Keeper / 3x Hammer Modifications; - Hydraulically Tilt Rotary Head - Rotary changed to geared Rotary Head with Hollow Spindle (8,000 Nm Torque) - Including 2x Eaton Hydraulic Motors - Side Shift (on rotary head – opens up the tower for longer casing, etc.) Support Truck Make: Volvo Model: FH12 460 KM’s: 1,040,378 Type: 8x4 Air Compressor Make: Atlas Copco Model: XRV1200 Year: 2020 Hours: 122 Engine: Cummins Pressure: 22.7 bar / 330 PSI Engine/Motor Speed: 1,900 RPM Engine/Motor Power: 325 kW / 430 HP 1,200 CFM / 330 PSI - Included Drill Bits, Rods and Drilling Equipment Trailerised Drill Rig Support Truck Air Compressor Package Location: New Zealand Learn More

Make: Schramm Model: T660 H Rotadrill Engine: Caterpillar CAT 3406B DITA @ 450 HP Pulldown: 30,000 lbs Pullback: 44,000 lbs Capacity: 5" Inch Rams / 350 m R/C 4 1/2" Inch Remet Rods Stroke: 6.5 m Top Drive: R/C Head Twin Motor 2 Speed / 0-160 RPM @ 38,000 lbs / 0-53 RPM @ 75,000 lbs Onboard Air Compressor: Sullair 900 CFM / 350 PSI Mounting: Caterpillar CAT 325 Wide Track Track Mounted Drill Rig Location: New Zealand Learn More