Search results for: 'spare rods hose for seri'

Rig Make: UDR Model: 650 Hours: 9,202 - Commissioned Mid 2023 - Onboard PTO Driven Air Compressor - New water pump - New fan belts - New radiator core - Recent service with oil & new filters - New rod & piston seals to main feed Ram - New Dump Mast Ram - New rods & seals to mast raise rams - New side shift ram - New break out ram - New rod crane raise ram - New hydraulic valve blocks in control cabinet for main pump & secondary pump controls - New micro control fine feed controller - Replaced majority of gauges with new - New main rotation shaft seals & speedy sleeves - New main rotation torque control cartridge - New hammer oiler pump - New seats & O rings in majority of valve banks Air Compressor - New Air / Oil separator filter - New Oil stop valve - New Castrol Aircoil 68 synthetic oil - New filters - Recently been serviced by Midcoast Compressors Truck Make: MAN Year: 1997 KM's: 200,000 Type: 8x8 Transmission: Recon 18 Speed Gear Box - Kevrek 1500 Hiab Crane with Winch & Umbilical Cord Remote - Radiator back flushed - New Water Pump - New Fan Belts - New brake boosters on every wheel - New four way valve - New valve on brake pedal - Rebuilt Truck Compressor - New air on drivers seat - New air valves on diff locks / cross locks - New clutch, fly wheel & pressure plate - New bearings & seals in Dana drive box - New oil pump on Dana drive box - New universals on tail shafts - New ram on power steering - New tyres all around - All ball joints on truck replaced that were needed, or new rubbers on them - Recently passed Pit Inspection - 7 months Rego as Plant - No need for overhang permits; within length Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Make: Drillmec Quantity: 4 Rod Loaders Location: Queensland, Australia Learn More

Make: Ford Model: 9000 L Series Year: 1990 Cab Chassis Truck Location: Queensland, Australia Learn More

Rig Make: Edson Model: Versadrill 300 Year: 1996 Engine: Hatze - 6x6 Multidrive Technology - Rotation head MR260 Rotation hollow spindle, single speed, dial in, rotation head around 120 rpm - Winching gear on back of mast for hollow augering - Can do diamond drilling if you were to change the hydraulic motor - Dump Mast - Near New Hydraulic Pump - 4x Leveling Jacks - Currently doing 80mtr holes at 4.5” - Client used to aircore with it, but currently set up doing mud - Used to do a lot of Geotech work, 6” hollow augering - Southern Cross Mud pump on the side - 3.2 mtr Stroke - 3 mtr Rods - Extension arm to run 6mtr casing into the ground Ute Make: Toyota Model: Landcruiser Year: 1990 KM's: 107,000 Ute Mounted Drill Rig Location: Western Australia Learn More

Make: Atlas Copco Model: Pit Viper 275 Hours: 19,237 Load Capacity: 75,000 lb Engine: Caterpillar CAT C32 - 4 Rod Carousel approx. 40 ft. - Atlas Copco QAS 45 Diesel Generator Dimensions; Length: 41ft. 6 inch / 63ft. 6 inch (Tower Down) Width: 18ft. 4 inch Height: 67ft. / 22ft 1 inch (Tower Down) Track Mounted Drill Rig Location: Canada Learn More

Make: Sandvik Model: UDR300D (DE740) Main Winch: 9 m Pull - 30 Tonne Pull Back - 2x Main Traverse Cylinders - Fully Hosed - 3.5 m Stroke - Vertically Stacking Monkey Board - New & Unused Dump Mast Location: Queensland, Australia Learn More

Make: GN Solids Control Model: LW450 1000N Year: 2012 Hours: 0 (Unused) Drum Rotate Speed: 1,800 RPM Aux Power: 7.5 kW Dimension: 2,600 / 1,850 / 1,750 mm Weight: 2,700 kg - Skid Removable and Adjustable Legs - 18" Inch Bowl - 3 Phase 7.5 kW Scroll Motor, 30 kW Bowl Motor and 7 kW Feed Pump Motor - Reconditioned Cemo Variable Drive Feed Pump (Mono Style Screw Pump) with New Rotor and Stator - Spare Second Hand Feed Pump along with brand new stator and rotor. Skid Mounted Centrifuge Location: Victoria, Australia Learn More

Make: Mayhew Junior Length: 6 Metre Condition: 50% Approx. Drill Rod / Pipe Location: Victoria, Australia Learn More

Make: UDR Rod Spinner Location: Victoria, Australia Learn More

Rig Make: Boart Longyear Model: LF90 Year: 2008 Hours: 14,154 - Fitted with KWL 400 Head as Top Drive - Masts are locked at 6 Metre Rod Pull - Has been drilling in Iron Ore Truck Make: Tatra Year: 2008 KM's: 37,735 Type: 8x8 Truck Mounted Drill Rig Location: Western Australia Learn More

Make: Emsco Model: DA700 Engine: Cummins 903 - Diesel Driven - Spare Mud Pump - Heaps of Critical Spares Condition: Good Skid Mounted Mud Pump Location: Victoria, Australia Learn More

Make: Rotacan Type: 9 1/4" Inch OD Thickness: 1 1/4" Inch Beco 6 Length: 25 Foot Quantity: 12 Condition: New (Without Use) Drill Rod / Pipe Location: Chile Learn More

Make: Ford Louisville Model: LTL9000 Year: 1990 Engine: Detroit Series 60 13 Litre @ 500 HP Transmission: Roadranger RT14715 Diff: 44,000 lbs Suspension: Hendrikson 44,000 kg Walking Beam - Spare Bonnet with Truck Truck Location: Queensland, Australia Learn More

Make: Mole Pioneer Model: P400S 450HQ Hours: 2,940 Engine: Perkins 119 kW Diesel - Onboard W1122 Bean Pump Rotation Head Model: KL400 Top Drive Stroke: 1,200 mm Drilling Angle: 90 degrees vertical to 45 degrees horizontal Drilling Depth Capacity B Size: 900 metres N Size: 700 metres H Size: 450 metres P Size: 275 metres Truck Make: Ford Model: Cargo Series KM's: 25,372 Year: 1985 Type: 6x4 Condition: Good *For more information, please contact us* Mole Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Drill Rig Make: Chicago Pneumatic Model: CP650 Year: 1981 Engine: Caterpillar CAT 3406 Onboard Air Compressor: GHH 825 CFM / 350 PSI Twin Screw Injection Pump: Comet APS 71 ltr/min @ 580 PSI Casing Driver: 612 Banger 6" Inch - 12" Inch Winch: 1/2" Inch 7,000 lbs Extendable Rod Handling Jib Hole Capacity: 6" Inch - 12" Inch 500 m 4 1/2" Inch Rods Capacity; Pull Down: 21,000 lbs Pull Back: 55,000 lbs 5 1/2" Inch Heavy Hoist Rams 73 ft/min Rapid Feed - 160 Pitch Chains Levelling Jacks; Front: 1 x 5" Inch x 48" Inch Stroke Rear: 2 x 5" Inch x 36" Inch Stroke Top Drive Rotary; 0-152 RPM - 76,000 lb Torque Twin Dynex Motors R/C Head - 7 m Travel Carrier Type: 6x4 Engine: Caterpillar CAT 3208 @ 210 HP Crane Carrier Carrier Mounted Water Well Drill Rig Location: New Zealand Learn More

Engine: Deutz 3FL2011 - Base Frame to support all components; engine, pump, hydraulics & fuel tanks, etc. - Fuel Tank Capacity: 60 Litres - Access Ladder to Control Platform - Paint, Two Pack Evolution Yellow Hydraulics; - Pump Group Bosch Rexroth - Main Pump A10VO45 Variable Displacement - Pilot Pump 5.5 cc Gear Pump - Maximum Circuit Pressure: 160 Bar - Hydraulic Oil Capacity: 100 Litres - Return Filter: 10 Micron - Hydraulic Oil Cooler and Fan Grout Pump; Make: Bredel Model: SPX 50 - Brevini BR100NC Hydraulic Motor - Slurry Flow Range: 0-85 lpm - Maximum Pressure: 15 Bar - Adjustable Speed Control Mixing Tank; Capacity: 1,400 Litres - Hydraulic Powered Agitator - Baffle Plates inside the tank - 3" Inch Outlet to Slurry Pump - Grid on tank top for cement dispersion during mixing - Sandblasted and painted with 2 pack paint Poly Reel; Capacity: 600 metres - 40 mm PN16 SDR11 Poly Pipe, Blue Stripe, 3.7 mm Wall - Fabricated construction approx. 2.1 metres diameter - Hydraulic Drive via reduction gearbox and chain + sprocket final drive - Adjustable Speed Control: 1.5-30 m/min Control Platform; - Mounted near mixing tank - Engine controls, start, stop, throttle, etc. - Hydraulic controls for agitator, slurry pump and hose reel Dimensions; Length: 4.65 m Width: 2.35 m Hight: 2.5 m Weight: 3,500 kg approx. Skid Mounted Grouting Unit Location: Australia Learn More

Model: WP500 Engine: Cummins QSB 4.5 @ 119 kW (160 HP) Fuel Tank Capacity: 200 Litres Estimated Weight: 2,890 kg (excluding trailer) - Base Frame to support engine, pumps, hydraulics and fuel tanks, etc. - Paint, Two Pack Evolution Yellow Hydraulics; - Pump Group Bosch Rexroth - A11VO95/A10VO85/16 - Maximum Circuit Pressure: 250 Bar - Hydraulic Oil Capacity: 400 Litres - Return Filter: 10 Micron - Hydraulic Oil Cooler and Fan Water Pumps; Make: FMC Model: L11-18SC Water Flow Range: 0-530 lpm (140 US/GPM) Maximum Water Pressure: 69 Bar (1,000 PSI) - Adjustable Water Pressure Relief Valve - Water Discharge Pressure Gauge - Surge Chambers on suction & discharge - Discharge Pulsation Dampener - Volvo fixed displacement Piston Drive Motors - Flex Drive Couplings - 2" Inch Water Delivery Hose x 10 metres long Control Panel; - Remote Pilot Hydraulic Control to attach at Rig Control Panel - Selectable Pump 1, 2 or both - Adjustable Friction Lock Control - Selectable Fine Speed Control on Pump 1 - Interconnecting Hoses 10 metres long Skid Mounted Mud Pump Location: Australia Learn More

Body Opening: 225 mm (8 3/4" Inch) OD - Fabricated High Tensile Steel Base Frame for increased strength and lighter unit weight - High Tensile Fabricated Lever Arms - Adjustable Connecting with Left & Right Hand Threads allowing accurate adjustment of jaw actuation - Cast Jaw Assemblies to suit most standard drill rod sizes - Light weight casting approx. 16 kg per jaw - Easily replaceable Gripper Inserts for NQ & HQ Jaw Sizes - RC Slips Table, Holders and Inserts to suit 3 1/2", 4" & 4 1/2" Rod Sizes - Changeable with Industry Standard Rod Clamps Rod Clamp Location: Australia Learn More

Model: FH3000 Engine: Cummins QSL Electronic @ 255 kW (342 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Maximum Speed: 55.5 m/min (182 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - 100% Theoretical Main Winch; - Maximum Pull: 226 kN (50,806 lbf) - Maximum Speed: 100 m/min (328 ft/min) - 2x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release - 9 Metre Rod Pull Capacity Wireline Winch; - Maximum Pull: 27 kN (6,069 lbf) - Rope Capacity: 3,000 Metres x 8 mm Rope - Maximum Speed: 450 m/min (1,476 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH2000 Engine: Caterpillar CAT C7.1 Electronic @ 205 kW (275 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Up: 50 m/min (164 ft/min) Down: 39 m/min (128 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - Bosch Rexroth A6VM160 Variable Displacement Motor - High Gear 3:1 & Low Gear 19.57:1 ratios - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube Bearings and Gears with filtered and cooled lubrication oil system Main Winch; - Maximum Pull: 156 kN (35,048 lbf) - 120 m/min (394 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - 28 mm Main Winch Rope - Safety Factor 3.35:1 (exceeds BS/EN791) - 1x Bosch Rexroth A6VM160 Variable Displacement Motors - 1x Brevini Planetary Reduction Gear Boxes - 1x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release Wireline Winch; - Mast Mounted - Maximum Pull: 25 kN (5,617 lbf) - Rope Capacity: 2,100 Metres x 8 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More