Search results for: 'state rods hire for seri'

Rig Make: UDR Model: 650 Hours: 9,202 - Commissioned Mid 2023 - Onboard PTO Driven Air Compressor - New water pump - New fan belts - New radiator core - Recent service with oil & new filters - New rod & piston seals to main feed Ram - New Dump Mast Ram - New rods & seals to mast raise rams - New side shift ram - New break out ram - New rod crane raise ram - New hydraulic valve blocks in control cabinet for main pump & secondary pump controls - New micro control fine feed controller - Replaced majority of gauges with new - New main rotation shaft seals & speedy sleeves - New main rotation torque control cartridge - New hammer oiler pump - New seats & O rings in majority of valve banks Air Compressor - New Air / Oil separator filter - New Oil stop valve - New Castrol Aircoil 68 synthetic oil - New filters - Recently been serviced by Midcoast Compressors Truck Make: MAN Year: 1997 KM's: 200,000 Type: 8x8 Transmission: Recon 18 Speed Gear Box - Kevrek 1500 Hiab Crane with Winch & Umbilical Cord Remote - Radiator back flushed - New Water Pump - New Fan Belts - New brake boosters on every wheel - New four way valve - New valve on brake pedal - Rebuilt Truck Compressor - New air on drivers seat - New air valves on diff locks / cross locks - New clutch, fly wheel & pressure plate - New bearings & seals in Dana drive box - New oil pump on Dana drive box - New universals on tail shafts - New ram on power steering - New tyres all around - All ball joints on truck replaced that were needed, or new rubbers on them - Recently passed Pit Inspection - 7 months Rego as Plant - No need for overhang permits; within length Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Make: Drillmec Quantity: 4 Rod Loaders Location: Queensland, Australia Learn More

Make: Ford Model: 9000 L Series Year: 1990 Cab Chassis Truck Location: Queensland, Australia Learn More

Rig Make: Edson Model: Versadrill 300 Year: 1996 Engine: Hatze - 6x6 Multidrive Technology - Rotation head MR260 Rotation hollow spindle, single speed, dial in, rotation head around 120 rpm - Winching gear on back of mast for hollow augering - Can do diamond drilling if you were to change the hydraulic motor - Dump Mast - Near New Hydraulic Pump - 4x Leveling Jacks - Currently doing 80mtr holes at 4.5” - Client used to aircore with it, but currently set up doing mud - Used to do a lot of Geotech work, 6” hollow augering - Southern Cross Mud pump on the side - 3.2 mtr Stroke - 3 mtr Rods - Extension arm to run 6mtr casing into the ground Ute Make: Toyota Model: Landcruiser Year: 1990 KM's: 107,000 Ute Mounted Drill Rig Location: Western Australia Learn More

Make: Atlas Copco Model: Pit Viper 275 Hours: 19,237 Load Capacity: 75,000 lb Engine: Caterpillar CAT C32 - 4 Rod Carousel approx. 40 ft. - Atlas Copco QAS 45 Diesel Generator Dimensions; Length: 41ft. 6 inch / 63ft. 6 inch (Tower Down) Width: 18ft. 4 inch Height: 67ft. / 22ft 1 inch (Tower Down) Track Mounted Drill Rig Location: Canada Learn More

Make: Mayhew Junior Length: 6 Metre Condition: 50% Approx. Drill Rod / Pipe Location: Victoria, Australia Learn More

Make: UDR Rod Spinner Location: Victoria, Australia Learn More

Rig Make: Boart Longyear Model: LF90 Year: 2008 Hours: 14,154 - Fitted with KWL 400 Head as Top Drive - Masts are locked at 6 Metre Rod Pull - Has been drilling in Iron Ore Truck Make: Tatra Year: 2008 KM's: 37,735 Type: 8x8 Truck Mounted Drill Rig Location: Western Australia Learn More

Includes; - Kitchen - Lunch Room / Work Space Room - Storage Dual-Axle Van Location: Australia Learn More

Make: Rotacan Type: 9 1/4" Inch OD Thickness: 1 1/4" Inch Beco 6 Length: 25 Foot Quantity: 12 Condition: New (Without Use) Drill Rod / Pipe Location: Chile Learn More

Generator: Honda 2kVA Dimensions; Length: 4 Metres (Inc. Trailer) Width: 1.6 Metres Height: 2.5 Metres Cold Room: 1.2 m x 1.2 m x 1.8 m - Fully Insured & Ready to Go - Mobile- Galvanised Trailer - 2,500 Litre Cold Room - Holds 4x Kegs with 4x Taps (2 Either Side) - Drip Trays on Both Sides - Extra Cold Room Storage - Pull Out Shade Cloths on Both Sides - Party Hire - Camping - Beach Party (Trailer is Purpose Built) - Functions - Corporate - Event Management - Fundraisers Mobile Keg & Chill Cold Room Trailer Location: Queensland, Australia Learn More

Make: Ford Louisville Model: LTL9000 Year: 1990 Engine: Detroit Series 60 13 Litre @ 500 HP Transmission: Roadranger RT14715 Diff: 44,000 lbs Suspension: Hendrikson 44,000 kg Walking Beam - Spare Bonnet with Truck Truck Location: Queensland, Australia Learn More

Make: Mole Pioneer Model: P400S 450HQ Hours: 2,940 Engine: Perkins 119 kW Diesel - Onboard W1122 Bean Pump Rotation Head Model: KL400 Top Drive Stroke: 1,200 mm Drilling Angle: 90 degrees vertical to 45 degrees horizontal Drilling Depth Capacity B Size: 900 metres N Size: 700 metres H Size: 450 metres P Size: 275 metres Truck Make: Ford Model: Cargo Series KM's: 25,372 Year: 1985 Type: 6x4 Condition: Good *For more information, please contact us* Mole Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Includes; - Kitchen - Lunch Room / Work Station Room - Generator - 2x Toilets Tri-Axle Van Location: Australia Learn More

Drill Rig Make: Chicago Pneumatic Model: CP650 Year: 1981 Engine: Caterpillar CAT 3406 Onboard Air Compressor: GHH 825 CFM / 350 PSI Twin Screw Injection Pump: Comet APS 71 ltr/min @ 580 PSI Casing Driver: 612 Banger 6" Inch - 12" Inch Winch: 1/2" Inch 7,000 lbs Extendable Rod Handling Jib Hole Capacity: 6" Inch - 12" Inch 500 m 4 1/2" Inch Rods Capacity; Pull Down: 21,000 lbs Pull Back: 55,000 lbs 5 1/2" Inch Heavy Hoist Rams 73 ft/min Rapid Feed - 160 Pitch Chains Levelling Jacks; Front: 1 x 5" Inch x 48" Inch Stroke Rear: 2 x 5" Inch x 36" Inch Stroke Top Drive Rotary; 0-152 RPM - 76,000 lb Torque Twin Dynex Motors R/C Head - 7 m Travel Carrier Type: 6x4 Engine: Caterpillar CAT 3208 @ 210 HP Crane Carrier Carrier Mounted Water Well Drill Rig Location: New Zealand Learn More

Body Opening: 225 mm (8 3/4" Inch) OD - Fabricated High Tensile Steel Base Frame for increased strength and lighter unit weight - High Tensile Fabricated Lever Arms - Adjustable Connecting with Left & Right Hand Threads allowing accurate adjustment of jaw actuation - Cast Jaw Assemblies to suit most standard drill rod sizes - Light weight casting approx. 16 kg per jaw - Easily replaceable Gripper Inserts for NQ & HQ Jaw Sizes - RC Slips Table, Holders and Inserts to suit 3 1/2", 4" & 4 1/2" Rod Sizes - Changeable with Industry Standard Rod Clamps Rod Clamp Location: Australia Learn More

Model: FH3000 Engine: Cummins QSL Electronic @ 255 kW (342 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Maximum Speed: 55.5 m/min (182 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - 100% Theoretical Main Winch; - Maximum Pull: 226 kN (50,806 lbf) - Maximum Speed: 100 m/min (328 ft/min) - 2x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release - 9 Metre Rod Pull Capacity Wireline Winch; - Maximum Pull: 27 kN (6,069 lbf) - Rope Capacity: 3,000 Metres x 8 mm Rope - Maximum Speed: 450 m/min (1,476 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH2000 Engine: Caterpillar CAT C7.1 Electronic @ 205 kW (275 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Up: 50 m/min (164 ft/min) Down: 39 m/min (128 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - Bosch Rexroth A6VM160 Variable Displacement Motor - High Gear 3:1 & Low Gear 19.57:1 ratios - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube Bearings and Gears with filtered and cooled lubrication oil system Main Winch; - Maximum Pull: 156 kN (35,048 lbf) - 120 m/min (394 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - 28 mm Main Winch Rope - Safety Factor 3.35:1 (exceeds BS/EN791) - 1x Bosch Rexroth A6VM160 Variable Displacement Motors - 1x Brevini Planetary Reduction Gear Boxes - 1x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release Wireline Winch; - Mast Mounted - Maximum Pull: 25 kN (5,617 lbf) - Rope Capacity: 2,100 Metres x 8 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1300 Engine: Caterpillar CAT C7.1 Electronic @ 187 kW (250 HP) Pull Back: 115 kN (25,853 lbf) Actual Pull Down: 70 kN (15,736 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 1,300 m HQ Core: 885 m Open Hole 3 1/2" Inch Rods: 380 m RC 4 1/2" Inch: 220 m (Nominal) Traverse Speed; Up: 60 m/min (196.8 ft/min) Down: 56 m/min (183.7 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 8,087 Nm (6,111 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - High Gear 3.04:1 & Low Gear 12.61:1 ratios - Variable Displacement 160cc Hydraulic Motor - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube System with Cooler and Filter Main Winch; - Maximum Pull: 100 kN (10,000 lbf) - 120 m/min (393 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - Main Winch Rope - Safety Factor to Meet BS/EN791 - Planetary Reduction Gear Box & Brake - Variable Displacement Hydraulic Motor Drive Wireline Winch; - Deck Mounted - Maximum Pull: 15 kN (3,372 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1000 Pull Back: 97 kN (21,783 lbf) Pull Down: 45 kN (10,116 lbf) Water Pump: Standard FMC W1122BCD 140 lpm @ 1,000 psi Depth Capacity; NQ Core: 1,150 m HQ Core: 786 m HWT Core: 518 m RC 4" Inch: 198 m (Nominal) Engine Options; - John Deere Power Tech 6.8L @ 155 kW (208 HP) - Caterpillar CAT C6.6 ACERT - Cummins B5.9-173 Traverse Speed; Up: 47 m/min (154 ft/min) Down: 30 m/min (98 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 5,965 Nm (4,400 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - 100% Theoretical Main Winch; - Maximum Pull: 88.4 kN (19,870 lbf) - 55 m/min (180 ft/min) - Mast Top Mounted - 1x Multi Disc Brake Unit - Fail Safe Spring Activated - Hydraulic Pressure Release - Main Winch Rope - Safety Factor to Meet BS/EN791 - 6 Metre Rod Pull Capacity Wireline Winch; - Deck Mounted - Maximum Pull: 13.5 kN (3,044 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Maximum Speed: 342 m/min (1,124 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More