Search results for: 'dozer state phim head hire clamp cjt64 cfm'

Drill Rig Make: Chicago Pneumatic Model: CP650 Year: 1981 Engine: Caterpillar CAT 3406 Onboard Air Compressor: GHH 825 CFM / 350 PSI Twin Screw Injection Pump: Comet APS 71 ltr/min @ 580 PSI Casing Driver: 612 Banger 6" Inch - 12" Inch Winch: 1/2" Inch 7,000 lbs Extendable Rod Handling Jib Hole Capacity: 6" Inch - 12" Inch 500 m 4 1/2" Inch Rods Capacity; Pull Down: 21,000 lbs Pull Back: 55,000 lbs 5 1/2" Inch Heavy Hoist Rams 73 ft/min Rapid Feed - 160 Pitch Chains Levelling Jacks; Front: 1 x 5" Inch x 48" Inch Stroke Rear: 2 x 5" Inch x 36" Inch Stroke Top Drive Rotary; 0-152 RPM - 76,000 lb Torque Twin Dynex Motors R/C Head - 7 m Travel Carrier Type: 6x4 Engine: Caterpillar CAT 3208 @ 210 HP Crane Carrier Carrier Mounted Water Well Drill Rig Location: New Zealand Learn More

Q80K - Top Head Drive - 0-8,328 Nm (6,142 ft/lbf) in low gear - High Gear 3.04:1 Ratio - Low Gear 12.61:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Gear train for High/Low Ratio Q150K - Top Head Drive - 0-14,324 Nm (10,564 ft/lbf) in low gear - High Gear 3:1 Ratio - Low Gear 22.5:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Planetary Gear set for High/Low Ratio Q280K - Top Head Drive - 0-28,000 Nm (20,651 ft/lbf) in low gear - High Gear 3:1 Ratio - Low Gear 22.5:1 Ratio - Shift between High and Low Gear Ratios - 0-1,500 RPM Speed Range - Splined Floating Spindle - Independent Pressurized Lubrication System - Gearbox oil level inspection windows - Variable Speed Hydraulic Motor - Dual Planetary Gear set for High/Low Ratio Rotation Head Gearboxes Location: Australia Learn More

Body Opening: 225 mm (8 3/4" Inch) OD - Fabricated High Tensile Steel Base Frame for increased strength and lighter unit weight - High Tensile Fabricated Lever Arms - Adjustable Connecting with Left & Right Hand Threads allowing accurate adjustment of jaw actuation - Cast Jaw Assemblies to suit most standard drill rod sizes - Light weight casting approx. 16 kg per jaw - Easily replaceable Gripper Inserts for NQ & HQ Jaw Sizes - RC Slips Table, Holders and Inserts to suit 3 1/2", 4" & 4 1/2" Rod Sizes - Changeable with Industry Standard Rod Clamps Rod Clamp Location: Australia Learn More

Model: FH3000 Engine: Cummins QSL Electronic @ 255 kW (342 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Maximum Speed: 55.5 m/min (182 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - 100% Theoretical Main Winch; - Maximum Pull: 226 kN (50,806 lbf) - Maximum Speed: 100 m/min (328 ft/min) - 2x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release - 9 Metre Rod Pull Capacity Wireline Winch; - Maximum Pull: 27 kN (6,069 lbf) - Rope Capacity: 3,000 Metres x 8 mm Rope - Maximum Speed: 450 m/min (1,476 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH2000 Engine: Caterpillar CAT C7.1 Electronic @ 205 kW (275 HP) Pull Back: 280 kN (62,900 lbf) Limited Speed 244.8 kN (55,033 lbf) Full Speed Pull Down: 115 kN (25,853 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 2,030 m HQ Core: 1,377 m Open Hole 3 1/2" Inch Rods: 900 m RC 4 1/2" Inch: 600 m (Nominal) Traverse Speed; Up: 50 m/min (164 ft/min) Down: 39 m/min (128 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 14,324 Nm (10,564 ft/lb) in low gear - 0-1,500 RPM Speed Range - Bosch Rexroth A6VM160 Variable Displacement Motor - High Gear 3:1 & Low Gear 19.57:1 ratios - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube Bearings and Gears with filtered and cooled lubrication oil system Main Winch; - Maximum Pull: 156 kN (35,048 lbf) - 120 m/min (394 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - 28 mm Main Winch Rope - Safety Factor 3.35:1 (exceeds BS/EN791) - 1x Bosch Rexroth A6VM160 Variable Displacement Motors - 1x Brevini Planetary Reduction Gear Boxes - 1x Multi Disc Brake Units - Fail Safe Spring Activated - Hydraulic Pressure Release Wireline Winch; - Mast Mounted - Maximum Pull: 25 kN (5,617 lbf) - Rope Capacity: 2,100 Metres x 8 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1300 Engine: Caterpillar CAT C7.1 Electronic @ 187 kW (250 HP) Pull Back: 115 kN (25,853 lbf) Actual Pull Down: 70 kN (15,736 lbf) Water Pump Options; - Standard FMC W1122BCD 140 lpm @ 1,000 psi - FMC L11-18SC 265 lpm @ 1,800 psi Depth Capacity; NQ Core: 1,300 m HQ Core: 885 m Open Hole 3 1/2" Inch Rods: 380 m RC 4 1/2" Inch: 220 m (Nominal) Traverse Speed; Up: 60 m/min (196.8 ft/min) Down: 56 m/min (183.7 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 8,087 Nm (6,111 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - High Gear 3.04:1 & Low Gear 12.61:1 ratios - Variable Displacement 160cc Hydraulic Motor - Adjustable Rotation Torque Control - Infinitely Variable Rotation Speed Control - Floating Spindle 3 1/2" Inch API IF Pin Thread - Pressure Lube System with Cooler and Filter Main Winch; - Maximum Pull: 100 kN (10,000 lbf) - 120 m/min (393 ft/min) - Mast Top Mounted - Electronic Winch Travel - Fail to safe - Main Winch Rope - Safety Factor to Meet BS/EN791 - Planetary Reduction Gear Box & Brake - Variable Displacement Hydraulic Motor Drive Wireline Winch; - Deck Mounted - Maximum Pull: 15 kN (3,372 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Adjustable Position Wireline Spooler - Maximum Speed: 450 m/min (1,476 ft/min) - Adjustable Pull Limiter - Safety Stop System - Wireline Depth Counter as an option New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: FH1000 Pull Back: 97 kN (21,783 lbf) Pull Down: 45 kN (10,116 lbf) Water Pump: Standard FMC W1122BCD 140 lpm @ 1,000 psi Depth Capacity; NQ Core: 1,150 m HQ Core: 786 m HWT Core: 518 m RC 4" Inch: 198 m (Nominal) Engine Options; - John Deere Power Tech 6.8L @ 155 kW (208 HP) - Caterpillar CAT C6.6 ACERT - Cummins B5.9-173 Traverse Speed; Up: 47 m/min (154 ft/min) Down: 30 m/min (98 ft/min) Rotation Head; - Top Head Drive - Maximum Torque: 5,965 Nm (4,400 ft/lb) in low gear - 0-1,500 RPM Speed Range - Two Speed Gearbox - 100% Theoretical Main Winch; - Maximum Pull: 88.4 kN (19,870 lbf) - 55 m/min (180 ft/min) - Mast Top Mounted - 1x Multi Disc Brake Unit - Fail Safe Spring Activated - Hydraulic Pressure Release - Main Winch Rope - Safety Factor to Meet BS/EN791 - 6 Metre Rod Pull Capacity Wireline Winch; - Deck Mounted - Maximum Pull: 13.5 kN (3,044 lbf) - Rope Capacity: 1,400 Metres x 6 mm Rope - Maximum Speed: 342 m/min (1,124 ft/min) New Build Multipurpose Track / Truck Mounted Drill Rig Location: Australia Learn More

Model: 1750 Scout Engine: Perkins Diesel Torque: 2,500 Nm at 205 bar and 110 RPM Stroke: 1.75 m Pull-Out / Pull-Down: 1,100 kg Capacity (Guide Only): NQ - 60 m / 4" Inch Open Hole - 30 m / 3 1/2" Inch Auger - 15 m - Custom Toyota 33220 Tray - Direct Dive Auger Head with High Torque Head Motor and Fittings - Fine Feed Control - Auger Drive Sub (1 1/8" Inch Hex) - RHS Mast - Tilt Frame for Vehicle/Trailer Mounting - Hydraulic Tilt - Heavy Duty Pull-Down Chain - Nylon Idler Rollers - Standard Auger Guide - Standard Control Panel - Hydraulic Operation - Rain Hood for Motor & Lockable Cage for Spare Wheel & Motor - Remove Throttle and Stop - Water Filter for Fuel / Water Separation - Light Guard for Augers 500 mm to 1,800 mm - Oil Cooler - Simple Rack for Augers Options for Drill; - Hollow Spindle Head and Tooling for Fluid Drilling - 2 Levelling Jacks for Tray Mount Drills - Tilting Rack for Augers - Alternative Engine Options to suit existing fleet Toyota Landcruiser Upgrade Kit; - Roof Racks for Spare Tyre (31678) - Roof Rack Mounts Pair (31679) - GVM Upgrade Spring Kit @ 4,200 kg (Supply Only - 31680) - Bellows Suspension Kit (Supply Only - 31730) - Storage Box LH Under Deck (33249) - Storage Box RH Under Deck (33248) - Under Deck Water Tanks @ 29 Litres (33137) *Ready for mounting to a Toyota 79 Series Landcruiser Cab Chassis* Drill Rig Location: Australia Learn More

Front Air Compressor Make: Sullair Model: 1,150 CFM / 350 PSI Year: 1998 Hours: 2,408 Engine: Cummins KTA19 Rear Air Compressor Make: Doosan Model: 1,350 CFM / 350 PSI Year: 1998 Hours: 977 Engine: Cummins K19 Condition: Serviceable - Both have current in date working Fire Suppression Systems - Active Shut Down Circuits - Mounted on a Howard Porter Licensed Trailer Twin Air Compressors Trailer Mounted Location: Western Australia Learn More

Make: UDR Replaced; - Hydraulic Ram - Tension Rod - L&R Couplings - Clamps have been 100% disassembled, reassembled and greased up - Jaw Holders supplied with the UDR but look unused (Can be purchased separately along with jaws) - Other Footclamp has Jaw Holders but look unused Footclamp Location: Malaysia Learn More

Make: Komatsu Model: D65PX-15 Year: 2008 Hours: 5,800 (Engine Overhaul) - Painted with Two Pack Track Mounted Crawler Dozer Location: Queensland, Australia Learn More

Make: Gardner Denver Model: 8x5 - Hydraulic Driven Trailer Mounted Mud Pump Location: New South Wales, Australia Learn More

Make: Hydco Model: 1000H Year: 2008 Hours: 4,304 Engine: Cummins 6CTA Onboard Air Compressor: Sullair 1,150 CFM / 350 PSI & 900 CFM / 500 PSI Compressor Hours: 819 Compressor Engine: Caterpillar CAT C15 - Setup for mainly RC however has the diamond capabilities & equipment - Rig has recently been completing RC holes to depths of 425 m coupled with the Aux Compressor Kit giving 2,400 CFM / 1,000 PSI Diamond Drilling Capacity; HQ: 1,000 m NQ: 1,500 m PQ: 600 m Features; - Harlsan Auto Blow Up and Blowdown - KL Rod Handler - Hydraulic Breakouts - Hydraulic Spanners - Safety Cage with Interlock - Quick Access Mountable Stuffing Box Assembly - Fire Suppression - Dust Suppression - FMC Bean Pump for Diamond Drilling - FMC Dual Pump for Water Injection - Hydraulic Foot Clamps - Diamond Drilling Safety Cage - Diamond Drilling Platform - Storage Area with Safety Rails and Access Ladders - Refurbished Cyclone - New Cone Splitter - New Track Chains and Rollers - 400x Metres of 4.5" Inch Remet Rods - Airdrill 670 Hammers & Bits - Other specific RC Gear Track Mounted Drill Rig Location: Western Australia Learn More

Engine: Caterpillar CAT 3412 V12 Hours: TBA Year: 1997 approx. Air Compressor Make: Sullair 1,800 CFM 200 PSI Booster Make: Aerial 1,800 RPM 500 PSI Air Compressor / Booster Skid Mounted Package Location: Western Australia Learn More

Make: Keypower Model: 6V92TA1400 Max Inlet Pressure: 2,413 kPa / 350 PSI Max. Delivery: 660 l/sec / 1,400 CFM Max. Discharge Pressure: 5,171 / 850 PSI Compression Ratio: 2:1 (Nominal) / 3:1 (Maximum) Bore: 57 mm Stroke: 127 mm Max. Operating Angle: 15 degrees Engine: Detroit 6V92TA Diesel *Not Actual Photo of Unit* Skid Mounted Booster Location: New South Wales, Australia Learn More

Make: Gardner Denver Model: PZ-7 Year: 2014 - Triplex w/ Forged Steel Fluid End & Quick Change Caps - 5M Pulsation Dampener - Oteco 3" Inch Shear Relief Valve - Pressure Gauge - Mission 6x5 Charge Pump - Fitted with 7" Inch Liners & Pistons - No Engine or Transmission Condition: Good Skid Mounted Mud Pump Location: United States of America Learn More

Make: Cubex Model: QXR 920 Year: 2004 (Rebuild 2019) Hours: 16,896 Engine: Caterpillar CAT C15 Rotary Head: Cubex @ 6,230 hours (Rebuilt May 2019) Rotation Torque: 5,730 Nm Rotation Speed: 0-80 RPM Variable Jaw Rotation: 15 degrees Clamping Force: 288 kN Carousel Capacity: 6 Rods Max. Rod Size: 5" Inch Min. Rod Size: 3.25 " Inch Rod Length: 6 m / 20 ft Onboard Air Compressor: Sullair + Spares Included Track Mounted Surface Drill Rig Location: Western Australia Learn More

Make: Globe Drill Model: KAL 500-CP8 Year: 2009 Hours: 27,332 (Lifetime) / Current Hours: 3,406 Engine: Detroit Series 2000 @ 905 HP Engine Hours: 11,982 Onboard Air Capacity: 1,350 CFM / 500 PSI Hole Inclination: 90-50 degrees Rod String: No Rods - Set up for 4 1/2" Inch Rods Depth Capacity On Board: 330 m Overall Width: 3.9 m Compressor Make: Sullair 1,350 CFM 500 PSI Hours: 2,308 Features; - Polyurethane Cyclone - Cone Sample Splitter - Dual Breakout System - Dust Suppression - Carousel - Rod Cage - Overhead Protection - Fire Suppression - Remote Tramming Track Mounted Drill Rig Location: Western Australia Learn More

74x Halco Mach 44 4 1/2" Inch Convex Domed Condition: New / Used (Rust) 33x Halco Mach 44 4 1/4" Inch Convex Domed Condition: New / Used (Rust) 1x Halco Mach 44 4 1/2" Inch Concave Domed Condition: New 3x Halco Mach 44 4 1/8" Inch Convex Domed Condition: New 34x Halco Mach 303 3 1/2" Inch Convex Ballistic Condition: New 3x Karbo 4 1/2" Inch Convex Condition: New 4x Karbo 4 1/2" Inch Convex Condition: 3x New / 1x Used Various Size, Shank, Head & Insert Drill Bits Location: Canada Learn More

Make: Custom Model: 600 RRD Motor: 40 HP TEFC Pulling Capacity: 24,000 lbs Lifting Capacity: 24,000 lbs Down Thrust Capacity: 12,500 lbs Rotational Torque: 6,500 ft/lbs Load Sensing Power Limiting Pump: 45 GPM @ 1,700 PSI Load Sensing Diesel Pump: 15 GPM @ 3,500 PSI Fast Feed: 14.79 GPM @ 2,500 PSI Slow Feed: 6.2 GPM @ 2,500 PSI Traction Hydraulic Motor: 14 HP each at 4,000 MASL (Using Diesel Drive) Max. Drilling Air Pressure: 400 PSI Feed Cylinders Combined Bore: 9.8 sq inch Features; - Lubricator - Water Pump - Robust Mine Proven Construction - High Torque Rotation Head - Reversable Heavy Duty Mast - Efficient Electric/Hydraulic Drive - Fully Hydraulic Operation - Compact Size - Fully Variable Rotation Speed (0-24 RPM) Hydraulically Operated Crawlers - Remotely Operated Hydraulic Console for flexibility - Sting Cylinder - Dual Heavy Duty Feed System - 90 Degree Tilt Out Rotation Head - Longitudinal Shift - Side Shift - NEMA 4 - Air Motors for travelling Track Mounted Drill Rig Location: Canada Learn More