Search results for: 'high for size in drill rpm brand'

Doosan Air End Suitable for PA536, XHP1250 & XHP1170 Air Compressors ($48,000 ex GST) (sale-ehub4024)

For Sale

$48,000.00

Make: Doosan Models (Suitable): PA536, XHP1250 & XHP1170 - Brand New - Tailored to meet specific requirements - Inclusive of Warranty Air End Location: Australia Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	N/A	BRAND	Doosan
LOCATION	Australia	MODEL	PA536, XHP1250 & XHP1170

Add to Wish List Add to Compare

2006 Caterpillar CAT C15 Skid Mounted Engine ($59,000 ex GST) (sale-ehub4016)

For Sale

$59,000.00

Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More

Machine hours	1,400	KILOMETERS	N/A
YEAR	2006	BRAND	Caterpillar CAT
LOCATION	Queensland, Australia	MODEL	C15

Add to Wish List Add to Compare

2010 Ubuilt Cassady CTU Coil Tubing Unit Mounted on 2005 Ensign Carrier ($295,000 ex GST) (sale-ehub4015)

For Sale

$295,000.00

Make / Model: Ubuilt Cassady CTU Carrier & Booster OD Year: 2010 Hours: 310 Engine: John Deere ATM: 61,500 kg Trailer Make: Ensign Model: C.T. 1000 Year: 2005 Tyre Size: 275/70R22.5 Rim Size: 8.25x22.5 Axle Group Load Carrying Capacity: 37,500 kg - Handrail and Stair Upgrade by Obadare CTU Coil Tubing Unit Carrier Mounted Location: Queensland, Australia Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	2010	BRAND	N/A
LOCATION	Queensland, Australia	MODEL	Ubuilt Cassady CTU Carrier & Booster OD

Add to Wish List Add to Compare

2007 Drill Rig Mounted on 2007 Isuzu FTS 750 4x4 Table Top Truck ($145,000 ex GST) (sale-ehub4003)

For Sale

$145,000.00

Rig Year: 2007 Hours: 3,000 Engine: Caterpillar (85 HP) Stroke: 3,300 mm - 2 Speed Head Rotation Torque: 2,500/450 Nm Rotation Speed: 140/750 RPM Pullback: 7,000 kg Pull Down: 4,000 kg - Set up for Geotechnical Drilling with Auto SPT - 1x Main Winch - 2x Wireline Winch - Mono Pump - Four Jack Legs - Drilling Rods, Alloy Mud Tanks, Accessories for 50 m (All in Good Condition) Truck Make: Isuzu Model: FTS 750 Year: 2007 KM's: 55,000 Type: 4x4 Table Top Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Machine hours	3,000	KILOMETERS	55,000
YEAR	2007	BRAND	N/A
LOCATION	Queensland, Australia	MODEL	N/A

Add to Wish List Add to Compare

TT300 Trailerised Drill Rig + Volvo FH12 460 Truck with Atlas Copco XRV1200 Air Compressor & More Package (POA) (sale-ehub3999)

For Sale

$0.00

Rig Model: TT300 Hours: 18 Engine: Deutz F6L912 / 66 kW Rated Depth Capacity: 300 m Feed Cylinder: 100 mm Barrel / 70 mm Shaft / 4 m Stroke Outrigger (Jacks): 4x Boxed Outriggers with 800 m Stroke Foam Pump: 21 Litre per min / 35 bar Foam/Water Tank: 120 Litre Axles: 2x 5 Tonne Air Braked Axles Tower: Direct on Cylinder / Triangle Shape Winch: 1 Tonne Push Down Force: 5,000 kgf @ 175 bar Pull Up Force: 13,000 kgf @ 175 bar Tilt Cylinders: 2x 80 Barrel 50 Shaft Breakout: 300 mm Stroke Cylinder Hydraulic Oil Tank Capacity: 330 Litres - Hydraulic Oil Cooler - Extended Tower to accommodate 4 m Stroke Cylinder - Spanners Included: 1x Breakout / 2x Keeper / 3x Hammer Modifications; - Hydraulically Tilt Rotary Head - Rotary changed to geared Rotary Head with Hollow Spindle (8,000 Nm Torque) - Including 2x Eaton Hydraulic Motors - Side Shift (on rotary head – opens up the tower for longer casing, etc.) Support Truck Make: Volvo Model: FH12 460 KM’s: 1,040,378 Type: 8x4 Air Compressor Make: Atlas Copco Model: XRV1200 Year: 2020 Hours: 122 Engine: Cummins Pressure: 22.7 bar / 330 PSI Engine/Motor Speed: 1,900 RPM Engine/Motor Power: 325 kW / 430 HP 1,200 CFM / 330 PSI - Included Drill Bits, Rods and Drilling Equipment Trailerised Drill Rig Support Truck Air Compressor Package Location: New Zealand Learn More

Machine hours	18	KILOMETERS	1,040,378
YEAR	2020	BRAND	N/A
LOCATION	New Zealand	MODEL	TT300

Add to Wish List Add to Compare

Schramm T660 H Rotadrill Track Mounted Drill Rig (POA) (sale-ehub3996)

For Sale

$0.00

Make: Schramm Model: T660 H Rotadrill Engine: Caterpillar CAT 3406B DITA @ 450 HP Pulldown: 30,000 lbs Pullback: 44,000 lbs Capacity: 5" Inch Rams / 350 m R/C 4 1/2" Inch Remet Rods Stroke: 6.5 m Top Drive: R/C Head Twin Motor 2 Speed / 0-160 RPM @ 38,000 lbs / 0-53 RPM @ 75,000 lbs Onboard Air Compressor: Sullair 900 CFM / 350 PSI Mounting: Caterpillar CAT 325 Wide Track Track Mounted Drill Rig Location: New Zealand Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	N/A	BRAND	Schramm
LOCATION	New Zealand	MODEL	T660 H

Add to Wish List Add to Compare

2012 ZJ50D/3150 Drill Rig (FOR HIRE/RENT - POA) (hire-ehub3991)

For Hire

Rig Model: ZJ50D/3150 Year: 2012 Mast Model: JJ315/45-K6 Substructure Model: DZ3159-S Drawworks Model: JC50D Power: 1,500 HP Rotary Table Model: ZP-375 Full Opening: 37.5” Inch Rotary Speed: 300 RPM Mud Pump Power: 1,600 HP Stroke: 120 RPM Working Pressure: 5,000 PSI Quantity: 2x Mud Tank Shaker Tank: 25 CuM Intermediate Tank: 40 CuM Suction and Mixing Tank: 20 CuM Solids Control - 3x Shale Shaker - 1x Mud Cleaner - 1x Centrifuge Drill Rig Location: Japan Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	Japan	MODEL	ZJ50D/3150

Add to Wish List Add to Compare

2007 Atlas Copco RD20-III Carrier Mounted Drill Rig (POA) (sale-ehub3983)

For Sale

$0.00

Make: Atlas Copco Model: RD20-III Year: 2007 Hours: 7,500 - In Good Working Order - Full Service Report Available This used 2007 RD20 Range III Atlas Copco Rig is a powerful and versatile drilling machine, ideal for a wide range of applications. Equipped with on IR 1,250 CFM / 350 PSI Air Compressor, this rig delivers exceptional performance and efficiency. Powered by a robust CAT C13 engine, the rig ensures smooth operation and ample power. The Cummins QSK19 deck engine further enhances its performance capabilities, delivering 755 HP for demanding drilling tasks. With a substantial pullback capacity of 120,000 lbs (54,446 kg), this rig can handle tough drilling conditions with ease. Mounted on a crane carrier truck, this RD20 III Atlas Copco Rig provides excellent mobility and stability. The rig has been meticulously maintained to ensure optimal condition and longevity. Its clean appearance reflects the owner’s commitment to proper care and maintenance. Carrier Mounted Drill Rig Location: New South Wales, Australia Learn More

Machine hours	7,500	KILOMETERS	N/A
YEAR	2007	BRAND	Atlas Copco
LOCATION	New South Wales, Australia	MODEL	RD20-III

Add to Wish List Add to Compare

2010 Soilmec SM-21 Track Mounted Rotary Drill Rig (POA) (sale-ehub3978)

For Sale

$0.00

Make: Soilmec Model: SM-21 Year: 2010 Hours: 132 - Brand New Engine (Under Warranty) - Rebuilt Rotation Head - New Hydraulic Track Mounted Rotary Drill Rig Location: Western Australia Learn More

Machine hours	132	KILOMETERS	N/A
YEAR	2010	BRAND	Soilmec
LOCATION	Western Australia	MODEL	SM-21

Add to Wish List Add to Compare

2010 IMS Bulwark 200 20 Tonne Work-Over Drill Rig ($75,000 ex GST) (sale-ehub3977)

For Sale

$75,000.00

Make: IMS Model: Bulwark 200 Year: 2010 Max Operating Wind Velocity: 12.5 m/sec Max Rated Hook Load: 196kN Height: 16 Metres 20 Tonne Work-Over Drill Rig Location: Queensland, Australia Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	2010	BRAND	IMS
LOCATION	Queensland, Australia	MODEL	Bulwark 200

Add to Wish List Add to Compare

2016 Safe-T BHA STS R1 Skid Mounted Jack Up Drill Rod Sloop ($120,000 ex GST) (sale-ehub3973)

For Sale

$120,000.00

Make: Safe-T Model: BHA STS R1 Year: 2016 - Surplus to requirements Skid Mounted Jack Up Drill Rod Sloop Location: Tasmania, Australia Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	2016	BRAND	N/A
LOCATION	Tasmania, Australia	MODEL	Safe-T BHA STS R1

Add to Wish List Add to Compare

Schramm T685 Drill Rig Mounted on 2008 MAN TGS 41.480 8x8 Truck (POA) (sale-ehub3967)

For Sale

$0.00

Drill Rig Make: Schramm Model: T685 Year: 2007 Engine: Cummins QSK19 Pullback Rating (Hoist Capacity): 33,884 kg Compressor: 2022 (Rebuild) Sullair DC 1,350 CFM / 500 PSI with Caterpillar C18 Compressor Hours: 3,200 (Shown) Triplex Pump: Bean 535 Pump Table Opening: 20" Inch Dual Breakouts: Metzke Hydraulic Breakout Tong Clutch: Direct Drive Set Up Rotation Head: Airdrill - Fold Down Walkways - Guarding (Spin cage with inter lock) - KL Road Loader (Hydraulic fixed) - 685WS Mast Truck Make: MAN Model: TGS 41.480 Year: 2008 KM's: 70,000 Transmission: Automatic Type: 8x8 - Mine Spec Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Machine hours	3,200 (Compressor)	KILOMETERS	70,000
YEAR	2008	BRAND	Schramm
LOCATION	Queensland, Australia	MODEL	T685

Add to Wish List Add to Compare

2013 Sandvik DC302R Self Propelled Drill Rig (POA) (sale-ehub3958)

For Sale

$0.00

Make: Sandvik Model: DC302R Year: 2013 Hours: 6,030 Engine Power: 62 kW Drifter: HL300 (8 kW) - Fully Reconditioned and Painted Self Propelled Drill Rig Location: Europe Learn More

Machine hours	6,030	KILOMETERS	N/A
YEAR	2013	BRAND	Sandvik
LOCATION	Europe	MODEL	DC302R

Add to Wish List Add to Compare

Hydramaster 2000 Cable Tool Drill Rig Mounted on 1998 International Acco 4x2 Truck & Tri Axle Trailer ($99,000 ex GST) (sale-ehub3957)

For Sale

$99,000.00

Rig Make: Hydramaster Model: 2000 - Fully Tooled & Spares - Recently painted Truck Make: International Model: Acco Year: 1998 KM's: 506,309 Type: 4x2 Engine: Cummins 300 HP Gearbox: 9 Speed Tri Axle Trailer - Near New - Set up for cable tool equipment Condition: Good Truck Mounted Cable Tool Drill Rig Tri Axle Trailer Location: Queensland, Australia Learn More

Machine hours	N/A	KILOMETERS	506,309
YEAR	1998	BRAND	Hydramaster
LOCATION	Queensland, Australia	MODEL	2000

Add to Wish List Add to Compare

2011 Hanjin D&B 1070CP Skid Mounted Air Compressor ($92,500 ex GST) (sale-ehub3953)

For Sale

$92,500.00

Make: Hanjin Model: D&B 1070CP Year: 2011 Hours: 3,443 Engine: Hyundai D6CC Power: 1,800 RPM / 530 HP Skid Mounted Air Compressor Location: Western Australia Learn More

Machine hours	3,443	KILOMETERS	N/A
YEAR	2011	BRAND	Hanjin
LOCATION	Western Australia	MODEL	D&B 1070CP

Add to Wish List Add to Compare

Sandvik DR560 Track Mounted DTH Drill Rig (POA) (sale-ehub3948)

For Sale

$0.00

Make: Sandvik Model: DR560 Hours: 2,610 Drifter Hours: 1,166 Track Mounted DTH Drill Rig Location: Chile Learn More

Machine hours	2,610	KILOMETERS	N/A
YEAR	N/A	BRAND	Sandvik
LOCATION	Chile	MODEL	DR560

Add to Wish List Add to Compare

Schramm 685 Track Mounted Drill Rig with Onboard Air Compressor ($1,200,000 ex GST) (sale-ehub3582)

For Sale

$1,200,000.00

Rig Make: Schramm Model: 685 Year: 1996 Hours: 2,500 (Since Rebuild) Engine: Cummins K19 Accessories; - FOPS - Rod Rack - 4x Levelling Jacks - In Mast Make/Break Rod Break Out System - Rotating Cyclone Set Up on Metz Manipulator - Airdrill Maker Breaker - Air Spanner - KL Rod Handler Set to 4.5" Inch Pipe - Dual RC Swivel and Auto Blow Down - ROPS Air-Conditioned Drillers Cabin - Complete Re-Hose 11/25 - Fire Suppression Air Compressor Make: Sullair 1,150 CFM / 500 PSI Water Capacity: Approx. 500 Litres Dimensions; Height: 4.6 m Width: 4.0 m Track Mounted Drill Rig Location: Queensland, Australia Learn More

Machine hours	2,500	KILOMETERS	N/A
YEAR	1996	BRAND	Schramm
LOCATION	Queensland, Australia	MODEL	685

Add to Wish List Add to Compare

Epiroc Pit Viper 275 Drill Rig Drive Shaft ($500 ex GST) (sale-ehub3941)

For Sale

$500.00

Make: Epiroc Model: Pit Viper 275 Part Number: 2657966534 Drill Rig Drive Shaft Location: Queensland, Australia Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	N/A	BRAND	Epiroc
LOCATION	Queensland, Australia	MODEL	Pit Viper 275

Add to Wish List Add to Compare

2007 Hydrapower Explorer 500 Drill Rig Mounted on 2005 MAN M2000 Truck (POA) (sale-ehub3938)

For Sale

$0.00

Rig Make: Hydrapower Model: Explorer 500 Year: 2007 Hours: 6,700 Engine: Cummins CPAK-6BTA Turbo After Cooled 6 Cylinder (176 HP @ 2,500 RPM) Rig Hydraulics; - Sauer Danfoss proportionally controlled control valves - Sauer closed loop pump on Rotary Drive Sauer open loop pump on auxiliary functions Rotary Drive; - Hydrapower Gearbox - Steel Casing with floating hollow spindle and hydraulic head lock and swing - Two Speed, 0 - 225 RPM & 0 - 966 RPM - Low speed torque to 4150 Nm - High speed torque to 966 Nm Head Travel: 6.8 m Main Winch; -Max. Pull: 4,200 kg -Max. Line Speed: 28 m/min Wireline Winch; Max. Pull: 780 kg Max. Line Speed: 83 m/min Pulldown; - Electrically controlled with dial for speed control Pull Down Capacity: 7000 kg Pull Out Capacity: 11,500 kg Mast; - Fitted with 2.0 m mast dump for angle drilling - Standard length is 10 m, supplied with hydraulically operated breakout spanner and top pulley swivel - Supplied with hydraulic circuit with quick-connect couplings for optional breakout table - Brakeout Table with Split Type Table - Bean Pump - 5x6 Gardner Denver Mud Pump (Hydraulic Driven) Truck Make: MAN Model: M2000 Year: 2005 KM's: 75,000 - Not registered - Some gearbox problems Truck Mounted Drill Rig Location: New South Wales, Australia Learn More

Machine hours	6,700	KILOMETERS	75,000
YEAR	2007	BRAND	Hydrapower
LOCATION	New South Wales, Australia	MODEL	Explorer 500

Add to Wish List Add to Compare

Exploration Drill Masters EDM MKII Track/Jack Up Rod Sloop Mounted Rod Feeder (EOI) (sale-ehub3931)

For Sale

$0.00

Make: Exploration Drill Masters EDM Model: MKII Hours: 539 Engine: Hatz 1D90V Max. Load Capacity: 15,000 kg Hydraulics: Rexroth 28CC Piston Pump - Capacity for 1,900 m NQ Drill Pipe in 6 m Lengths - 270 Degree Range of Movement - 2.1 m Arm Displacement - 4.770 m Roller Travel Roller Tramming Speed: 0.79 m/s Track Base Make: Sejin Model: 2P254075 Max. Speed: 0.6 km/h - 2 Speed Jack Up Base - 4 Extending Jack Legs - 1.8 m Jack Up Height Dimensions; Overall Platform Length: 8,460 mm Overall Platform Width: 2,500 mm Overall Height: 2,470 mm Empty Weight: 13,000 kg Clearance When Jacked Up: 1,650 mm Track Mounted Jack Up Rod Sloop Rod Feeder Location: Western Australia Learn More

Machine hours	539	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	Western Australia	MODEL	EDM MKII

Add to Wish List Add to Compare

Search results for: 'high for size in drill rpm brand'

AUSTRALIA WIDE SERVICE

REQUIRE ASSISTANCE - HAVE A QUESTION?

EQUIPMENT FOR HIRE OR FOR SALE