Search results for: 'hours for side new high pennsylvania'

2006 Caterpillar CAT C15 Skid Mounted Engine ($59,000 ex GST) (sale-ehub4016)

For Sale

$59,000.00

Make: Caterpillar Model: C15 Year: 2006 Hours: 1,533 • 440 HP @ 2,100 RPM • 1482LB-FT @ 1,400 RPM • Air to Air intercooled • 12 Volt (We can covert to 24 Volt if required) • SAE #1 flywheel housing multi fit industrial flywheel. • If required, we can supply and install a Caterpillar Air Compressor to the motor which runs off the auxiliary drive. The motor has been removed from the unit and fully workshop inspected and run up under load on the Dyno, results are as follows: Workshop inspection: • Intake manifold clean. • Cylinder head and rocker gear clean, no moisture or sludge, tune ok. • Turbocharge in nice condition, no excessive shaft play. • Camshaft in nice condition, no pitting • Crankshaft in good condition (Standard) • Main bearings and Con rod bearings in good condition – minimal wear • Crankshaft end float within spec Load test Report • Oil pressure: Cold Idle 70psi / Cold Top Revs 85psi / Hot Idle 50psi / Hot Top Revs 75psi • Water temps: Top Radiator 92 degrees. Bottom Radiator 69 degrees. • Thermostat opened and engine recovered correctly. • Turbocharger boost: 23 PSI @ 2,100 RPM • Breathing/ Blow by: 20 mm @ idle 30 mm @ 1,200 RPM 50 mm @ 1,350 RPM. 120 mm @ 1,800 RPM. • Smoke condition: small amount of black on startup, none at idle and very small white under full load. Skid Mounted Engine Location: Queensland, Australia Learn More

Machine hours	1,400	KILOMETERS	N/A
YEAR	2006	BRAND	Caterpillar CAT
LOCATION	Queensland, Australia	MODEL	C15

Add to Wish List Add to Compare

2010 Ubuilt Cassady CTU Coil Tubing Unit Mounted on 2005 Ensign Carrier ($295,000 ex GST) (sale-ehub4015)

For Sale

$295,000.00

Make / Model: Ubuilt Cassady CTU Carrier & Booster OD Year: 2010 Hours: 310 Engine: John Deere ATM: 61,500 kg Trailer Make: Ensign Model: C.T. 1000 Year: 2005 Tyre Size: 275/70R22.5 Rim Size: 8.25x22.5 Axle Group Load Carrying Capacity: 37,500 kg - Handrail and Stair Upgrade by Obadare CTU Coil Tubing Unit Carrier Mounted Location: Queensland, Australia Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	2010	BRAND	N/A
LOCATION	Queensland, Australia	MODEL	Ubuilt Cassady CTU Carrier & Booster OD

Add to Wish List Add to Compare

2009 & 2018 Caterpillar CAT D8T Track Mounted Bulldozer (POA) (sale-ehub4005)

For Sale

$0.00

Make: Caterpillar Model: D8T Year: 2009 & 2018 Hours; 2009: 10,723 2018: 15,100 - EPA Tier 3 (2009) / Tier 3 (2018) - MS Ripper (2009) - SS Ripper (2018) Track Mounted Bulldozer Location: Chile Learn More

Machine hours	10,723 & 15,100	KILOMETERS	N/A
YEAR	2009	BRAND	Caterpillar CAT
LOCATION	Chile	MODEL	D8T

Add to Wish List Add to Compare

2007 Drill Rig Mounted on 2007 Isuzu FTS 750 4x4 Table Top Truck ($145,000 ex GST) (sale-ehub4003)

For Sale

$145,000.00

Rig Year: 2007 Hours: 3,000 Engine: Caterpillar (85 HP) Stroke: 3,300 mm - 2 Speed Head Rotation Torque: 2,500/450 Nm Rotation Speed: 140/750 RPM Pullback: 7,000 kg Pull Down: 4,000 kg - Set up for Geotechnical Drilling with Auto SPT - 1x Main Winch - 2x Wireline Winch - Mono Pump - Four Jack Legs - Drilling Rods, Alloy Mud Tanks, Accessories for 50 m (All in Good Condition) Truck Make: Isuzu Model: FTS 750 Year: 2007 KM's: 55,000 Type: 4x4 Table Top Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Machine hours	3,000	KILOMETERS	55,000
YEAR	2007	BRAND	N/A
LOCATION	Queensland, Australia	MODEL	N/A

Add to Wish List Add to Compare

TT300 Trailerised Drill Rig + Volvo FH12 460 Truck with Atlas Copco XRV1200 Air Compressor & More Package (POA) (sale-ehub3999)

For Sale

$0.00

Rig Model: TT300 Hours: 18 Engine: Deutz F6L912 / 66 kW Rated Depth Capacity: 300 m Feed Cylinder: 100 mm Barrel / 70 mm Shaft / 4 m Stroke Outrigger (Jacks): 4x Boxed Outriggers with 800 m Stroke Foam Pump: 21 Litre per min / 35 bar Foam/Water Tank: 120 Litre Axles: 2x 5 Tonne Air Braked Axles Tower: Direct on Cylinder / Triangle Shape Winch: 1 Tonne Push Down Force: 5,000 kgf @ 175 bar Pull Up Force: 13,000 kgf @ 175 bar Tilt Cylinders: 2x 80 Barrel 50 Shaft Breakout: 300 mm Stroke Cylinder Hydraulic Oil Tank Capacity: 330 Litres - Hydraulic Oil Cooler - Extended Tower to accommodate 4 m Stroke Cylinder - Spanners Included: 1x Breakout / 2x Keeper / 3x Hammer Modifications; - Hydraulically Tilt Rotary Head - Rotary changed to geared Rotary Head with Hollow Spindle (8,000 Nm Torque) - Including 2x Eaton Hydraulic Motors - Side Shift (on rotary head – opens up the tower for longer casing, etc.) Support Truck Make: Volvo Model: FH12 460 KM’s: 1,040,378 Type: 8x4 Air Compressor Make: Atlas Copco Model: XRV1200 Year: 2020 Hours: 122 Engine: Cummins Pressure: 22.7 bar / 330 PSI Engine/Motor Speed: 1,900 RPM Engine/Motor Power: 325 kW / 430 HP 1,200 CFM / 330 PSI - Included Drill Bits, Rods and Drilling Equipment Trailerised Drill Rig Support Truck Air Compressor Package Location: New Zealand Learn More

Machine hours	18	KILOMETERS	1,040,378
YEAR	2020	BRAND	N/A
LOCATION	New Zealand	MODEL	TT300

Add to Wish List Add to Compare

Schramm T660 H Rotadrill Track Mounted Drill Rig (POA) (sale-ehub3996)

For Sale

$0.00

Make: Schramm Model: T660 H Rotadrill Engine: Caterpillar CAT 3406B DITA @ 450 HP Pulldown: 30,000 lbs Pullback: 44,000 lbs Capacity: 5" Inch Rams / 350 m R/C 4 1/2" Inch Remet Rods Stroke: 6.5 m Top Drive: R/C Head Twin Motor 2 Speed / 0-160 RPM @ 38,000 lbs / 0-53 RPM @ 75,000 lbs Onboard Air Compressor: Sullair 900 CFM / 350 PSI Mounting: Caterpillar CAT 325 Wide Track Track Mounted Drill Rig Location: New Zealand Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	N/A	BRAND	Schramm
LOCATION	New Zealand	MODEL	T660 H

Add to Wish List Add to Compare

Tulsa Triplex TT-560 Skid Mounted Triplex Mud Pump (POA) (sale-ehub3995)

For Sale

$0.00

Make: Tulsa Triplex Model: TT-560 Engine: Caterpillar CAT C15 Skid Mounted Mud Pump Location: New Zealand Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	New Zealand	MODEL	TT-560

Add to Wish List Add to Compare

2017 Sandman Mission Magnum Sandmaster 8x10x14 Trailerised Mud Pump ($67,500 ex GST) (sale-ehub3994)

For Sale

$67,500.00

Mud Pump Make: Sandman Model: Mission Magnum Sandmaster 8x10x14 Year: 2017 Engine: Cummins 6 Cylinder Diesel w/ Clutch - 8 Valve Discharge Manifold on back - 2x 8 Valve Suction Manifold on each side - Flow Meter Trailer Year: 2012 - Pindle Hitch Dimensions; Width: 7.6' Length: 16' Tyres: 245/70R17.5" Trailerised Mud Pump Location: New Zealand Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	2017	BRAND	N/A
LOCATION	New Zealand	MODEL	Mission Magnum Sandmaster 8x10x14

Add to Wish List Add to Compare

Baoji Oilfield Machinery F-800 Skid Mounted Mud Pump (POA) (sale-ehub3993)

For Sale

$0.00

Make: Baoji Oilfield Machinery Model: F-800 Skid Mounted Mud Pump Location: New Zealand Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	New Zealand	MODEL	F-800

Add to Wish List Add to Compare

2007 HD Engineering HR9000 Rotation Head (POA) (sale-ehub3992)

For Sale

$0.00

Make: HD Engineering Model: HR9000 Year: 2007 Rotation Head Location: New Zealand Learn More

Machine hours	N/A	KILOMETERS	N/A
YEAR	2007	BRAND	N/A
LOCATION	New Zealand	MODEL	HR9000

Add to Wish List Add to Compare

2023 XCMG XE55U Track Mounted Excavator ($105,000 ex GST) (sale-ehub3991)

For Sale

$105,000.00

Make: XCMG Model: XE55U Year: 2023 Hours: Less than 500 Includes; - Hammer - Auger Driver - 450 mm Auger - 300 mm Auger Track Mounted Excavator Location: New South Wales, Australia Learn More

Machine hours	Less than 500	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	New South Wales, Australia	MODEL	XE55U

Add to Wish List Add to Compare

10x 2021 Komatsu HD465-7E0 Dump Trucks (POA) (sale-ehub3989)

For Sale

$0.00

Make: Komatsu Model: HD465-7E0 Year: 2021 Hours: 9,000 - 17,280 Quantity: 10 Dump Trucks Location: China Learn More

Machine hours	9,000 - 17,280	KILOMETERS	N/A
YEAR	2021	BRAND	Komatsu
LOCATION	China	MODEL	HD465-7E0

Add to Wish List Add to Compare

2007 Atlas Copco RD20-III Carrier Mounted Drill Rig (POA) (sale-ehub3983)

For Sale

$0.00

Make: Atlas Copco Model: RD20-III Year: 2007 Hours: 7,500 - In Good Working Order - Full Service Report Available This used 2007 RD20 Range III Atlas Copco Rig is a powerful and versatile drilling machine, ideal for a wide range of applications. Equipped with on IR 1,250 CFM / 350 PSI Air Compressor, this rig delivers exceptional performance and efficiency. Powered by a robust CAT C13 engine, the rig ensures smooth operation and ample power. The Cummins QSK19 deck engine further enhances its performance capabilities, delivering 755 HP for demanding drilling tasks. With a substantial pullback capacity of 120,000 lbs (54,446 kg), this rig can handle tough drilling conditions with ease. Mounted on a crane carrier truck, this RD20 III Atlas Copco Rig provides excellent mobility and stability. The rig has been meticulously maintained to ensure optimal condition and longevity. Its clean appearance reflects the owner’s commitment to proper care and maintenance. Carrier Mounted Drill Rig Location: New South Wales, Australia Learn More

Machine hours	7,500	KILOMETERS	N/A
YEAR	2007	BRAND	Atlas Copco
LOCATION	New South Wales, Australia	MODEL	RD20-III

Add to Wish List Add to Compare

2022 Rebuilt SPM Weir TWS2250 Skid Mounted Jack Up Frac Mud Pump (FOR HIRE/RENT - POA) (hire-ehub3982)

For Sale

$0.00

Make: SPM Weir Model: TWS2250 Year: 2022 (Reman Rebuild) Hours: Approx. 7,000 Engine: Caterpillar CAT C32 (Rated @ 1,350 HP) Transmission: Allison 8000 Series Auto (DP8962R) Dimensions; Length: 9,135 mm (Overall) Width: 2,505 mm Height: 2,615 mm (On Ground) Height: 4,280 mm (Raised) Weight: 20,000 kg - When raised has enough height for a trailer of 1,500 mm to drive underneath Skid Mounted Jack Up Frac Mud Pump Location: Queensland, Australia Learn More

Machine hours	Approx. 7,000	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	Queensland, Australia	MODEL	SPM Weir TWS2250

Add to Wish List Add to Compare

2022 Rebuilt SPM Weir TWS2250 Skid Mounted Jack Up Frac Mud Pump (POA) (sale-ehub3982)

For Sale

$0.00

Make: SPM Weir Model: TWS2250 Year: 2022 (Reman Rebuild) Hours: Approx. 7,000 Engine: Caterpillar CAT C32 (Rated @ 1,350 HP) Transmission: Allison 8000 Series Auto (DP8962R) Dimensions; Length: 9,135 mm (Overall) Width: 2,505 mm Height: 2,615 mm (On Ground) Height: 4,280 mm (Raised) Weight: 20,000 kg - When raised has enough height for a trailer of 1,500 mm to drive underneath Skid Mounted Jack Up Frac Mud Pump Location: Queensland, Australia Learn More

Machine hours	Approx. 7,000	KILOMETERS	N/A
YEAR	N/A	BRAND	N/A
LOCATION	Queensland, Australia	MODEL	SPM Weir TWS2250

Add to Wish List Add to Compare

2010 Soilmec SM-21 Track Mounted Rotary Drill Rig (POA) (sale-ehub3978)

For Sale

$0.00

Make: Soilmec Model: SM-21 Year: 2010 Hours: 132 - Brand New Engine (Under Warranty) - Rebuilt Rotation Head - New Hydraulic Track Mounted Rotary Drill Rig Location: Western Australia Learn More

Machine hours	132	KILOMETERS	N/A
YEAR	2010	BRAND	Soilmec
LOCATION	Western Australia	MODEL	SM-21

Add to Wish List Add to Compare

Caterpillar CAT C11 Skid Mounted Engine with Integrated 800 Litre Diesel Tank ($39,500 ex GST) (sale-ehub3976)

For Sale

$39,500.00

Make: Caterpillar Model: C11 Hours: 17,316 - With Integrated 800 Litre Diesel Tank - Dyno Test Results and ECM Available 350 HP 1,800-2,100 Complete Package with Control Panel and Starter and Alternator Dimensions; Length: Overall 250 cm (Take off 50 cm if you relocate Air Cleaner) Height to top of Valve Cover (Engine): 120 cm To top of Pre-Cleaner: 180cm To top of Muffler: 220 cm Width: 110 cm (Radiator) Skid Mounted Engine Location: Australia Learn More

Machine hours	17,316	KILOMETERS	N/A
YEAR	N/A	BRAND	Caterpillar CAT
LOCATION	Australia	MODEL	C11

Add to Wish List Add to Compare

Schramm T685 Drill Rig Mounted on 2008 MAN TGS 41.480 8x8 Truck (POA) (sale-ehub3967)

For Sale

$0.00

Drill Rig Make: Schramm Model: T685 Year: 2007 Engine: Cummins QSK19 Pullback Rating (Hoist Capacity): 33,884 kg Compressor: 2022 (Rebuild) Sullair DC 1,350 CFM / 500 PSI with Caterpillar C18 Compressor Hours: 3,200 (Shown) Triplex Pump: Bean 535 Pump Table Opening: 20" Inch Dual Breakouts: Metzke Hydraulic Breakout Tong Clutch: Direct Drive Set Up Rotation Head: Airdrill - Fold Down Walkways - Guarding (Spin cage with inter lock) - KL Road Loader (Hydraulic fixed) - 685WS Mast Truck Make: MAN Model: TGS 41.480 Year: 2008 KM's: 70,000 Transmission: Automatic Type: 8x8 - Mine Spec Truck Mounted Drill Rig Location: Queensland, Australia Learn More

Machine hours	3,200 (Compressor)	KILOMETERS	70,000
YEAR	2008	BRAND	Schramm
LOCATION	Queensland, Australia	MODEL	T685

Add to Wish List Add to Compare

2013 Sandvik DC302R Self Propelled Drill Rig (POA) (sale-ehub3958)

For Sale

$0.00

Make: Sandvik Model: DC302R Year: 2013 Hours: 6,030 Engine Power: 62 kW Drifter: HL300 (8 kW) - Fully Reconditioned and Painted Self Propelled Drill Rig Location: Europe Learn More

Machine hours	6,030	KILOMETERS	N/A
YEAR	2013	BRAND	Sandvik
LOCATION	Europe	MODEL	DC302R

Add to Wish List Add to Compare

Hydramaster 2000 Cable Tool Drill Rig Mounted on 1998 International Acco 4x2 Truck & Tri Axle Trailer ($99,000 ex GST) (sale-ehub3957)

For Sale

$99,000.00

Rig Make: Hydramaster Model: 2000 - Fully Tooled & Spares - Recently painted Truck Make: International Model: Acco Year: 1998 KM's: 506,309 Type: 4x2 Engine: Cummins 300 HP Gearbox: 9 Speed Tri Axle Trailer - Near New - Set up for cable tool equipment Condition: Good Truck Mounted Cable Tool Drill Rig Tri Axle Trailer Location: Queensland, Australia Learn More

Machine hours	N/A	KILOMETERS	506,309
YEAR	1998	BRAND	Hydramaster
LOCATION	Queensland, Australia	MODEL	2000

Add to Wish List Add to Compare

Search results for: 'hours for side new high pennsylvania'

AUSTRALIA WIDE SERVICE

REQUIRE ASSISTANCE - HAVE A QUESTION?

EQUIPMENT FOR HIRE OR FOR SALE