DRILLING

Make: Hydco Model: 8V92-14C Hours: 8 Engine: Detroit 8V92TA Max Inlet Pressure: 350 PSI Max Delivery: 1,830 CFM Max Discharge Pressure: 900 PSI Bore: 57 mm (2 3/8") Stroke: 127 mm (5") 1,800 CFM 900 PSI Skid Mounted Booster Location: Western Australia Learn More

Rig Make: Hydco Model: 500RC Engine: Cummins QSM11 Hours: 9,000 Hydraulic Pumps: Rexroth A10VSO Series - They are all load sensing variable displacement piston pumps. 4 x A10VSO140 / 140cc 1 x A10VSO100 / 100cc 1 x A10VSO71 / 71cc Hydraulics: - Rexroth A10VSO Pumps, 4x140cc, 1 x100cc, 1x71cc. Variable displacement, load sensing. Nominal Pressure Peak Pressure 4061 psi/280 Bar 5076 psi/350 Bar - Hydraulic Driven air to oil Cooler. - Walvoil Pilot Control Valves (Rotation, Traverse, Fine Feed). - Danfoss PVG32 Load Independent Proportional Valves. load sensing feedback infinitely variable. Danfoss Rotation motors. Drill Mast: - HYDCO lattice drill mast with 160HTT chains. - 8m Stroke. - Traverse Max speed up 63 meters / minute. - Hydraulic cylinder over chains 2:1 ratio. - 3m mast dump. - Capable of angles from vertical to 45 degrees. - Hydraulic operated Rod guide. Rotation Head: - Air-Drill 2 speed Head (OMVW-630 Motors) Continuous Intermittent RPM * 0 - 83 0 - 101 Peak Torque ** 12,542 Nm (9,250 ft/lb) 14,658 Nm (10,811 ft/lb) Hydraulic Pressure 210 Bar (3,000 psig) 250 Bar (3,600 psig) Maximum Oil Flow 200 litres / min 240 litres / min Pullback: 30,000kg @ 2,340psi/161Bar 36,000kg @ 2,810psi/194Bar 52,000kg @ 4,061psi/280Bar (A10VSO Rexroth Pump Nominal Pressure) 65,000kg @ 5,076psi/350Bar (A10VSO Rexroth Pump Peak Pressure) Pulldown: 22,500kg @ 2,340psi/161Bar 27,000kg @ 2,810psi/194Bar 39,000kg @ 4,061psi/280Bar (A10VSO Rexroth Pump Nominal Pressure) 49,000kg @ 5,076psi/350Bar (A10VSO Rexroth Pump Peak Pressure) Survey Winch: - Capacity of 700m of 6mm wire rope. Rod Handling: - KL Rod Handler with hydraulic operation to suit drill pipe up to 4.5" diameter. - Rod Handling Boom, Slew and Raise functions, 4ton winch. - Hydraulic operated Breakout Wrench. Carrier Make / Model: Oshkosh Heavy Expanded Mobility Tactical Truck (HEMTT) Engine: Detroit Diesel 8V-92TA KM's: 160,000 Transmission: Allison HT740D Automatic Type: 8x8 - Right Hand Drive - Oshkosh Truck Corporation transfer case, 55000, Air Operated, Front Tandem Disconnect. - Eaton/Oshkosh Differential and Axles 1-RS480, 2-DS480, 3-DS480, 4-RS480. - Drive to the front axles is selectable and all axles have differential locks. - Hendrickson leaf spring with steel saddle, equalizing beams, 254mm vertical travel all round. Truck/Carrier Mounted Drill Rig Location: Queensland, Australia Learn More

Rig Make: Hydco Model: 1000H Year: 2008 Hours: 4,304 Engine: Cummins 6CTA Onboard Air Compressor: Sullair 1,150 CFM / 350 PSI & 900 CFM / 500 PSI Compressor Hours: 819 Compressor Engine: Caterpillar CAT C15 - Setup for mainly RC however has the diamond capabilities & equipment - Rig has recently been completing RC holes to depths of 425 m coupled with the Aux Compressor Kit giving 2,400 CFM / 1,000 PSI Diamond Drilling Capacity; HQ: 1,000 m NQ: 1,500 m PQ: 600 m Features; - Harlsan Auto Blow Up and Blowdown - KL Rod Handler - Hydraulic Breakouts - Hydraulic Spanners - Safety Cage with Interlock - Quick Access Mountable Stuffing Box Assembly - Fire Suppression - Dust Suppression - FMC Bean Pump for Diamond Drilling - FMC Dual Pump for Water Injection - Hydraulic Foot Clamps - Diamond Drilling Safety Cage - Diamond Drilling Platform - Storage Area with Safety Rails and Access Ladders - Refurbished Cyclone - New Cone Splitter - New Track Chains and Rollers - 400x Metres of 4.5" Inch Remet Rods - Airdrill 670 Hammers & BIts - Other specific RC Gear 2006 Tatra 8x8 Support Truck Make: Tatra Year: 2006 KM's: 123,864 approx. Type: 8x8 - Fitted with Custom Tanks Sand Storage for RC Support - Transfer Case recently replaced - 8,000 Litre Bulk Fuel - 4,000 Litre Water - Custom Storage for Hammers, etc. - 400x Metres of 4.5" Inch Remet Rods - Airdrill 670 Hammers - Bits with all Tooling and Spares - S-Reps Hammers Support Truck Track Mounted Drill Rig Package Location: Western Australia Learn More

Make: Hydco Model: 1000H Year: 2008 Hours: 4,304 Engine: Cummins 6CTA Onboard Air Compressor: Sullair 1,150 CFM / 350 PSI & 900 CFM / 500 PSI Compressor Hours: 819 Compressor Engine: Caterpillar CAT C15 - Setup for mainly RC however has the diamond capabilities & equipment - Rig has recently been completing RC holes to depths of 425 m coupled with the Aux Compressor Kit giving 2,400 CFM / 1,000 PSI Diamond Drilling Capacity; HQ: 1,000 m NQ: 1,500 m PQ: 600 m Features; - Harlsan Auto Blow Up and Blowdown - KL Rod Handler - Hydraulic Breakouts - Hydraulic Spanners - Safety Cage with Interlock - Quick Access Mountable Stuffing Box Assembly - Fire Suppression - Dust Suppression - FMC Bean Pump for Diamond Drilling - FMC Dual Pump for Water Injection - Hydraulic Foot Clamps - Diamond Drilling Safety Cage - Diamond Drilling Platform - Storage Area with Safety Rails and Access Ladders - Refurbished Cyclone - New Cone Splitter - New Track Chains and Rollers - 400x Metres of 4.5" Inch Remet Rods - Airdrill 670 Hammers & Bits - Other specific RC Gear Track Mounted Drill Rig Location: Western Australia Learn More